Modification of graphene oxide and its effect on properties of natural rubber/graphene oxide nanocomposites

• Nghiem Thi Thuong,
• Le Dinh Quang,
• Vu Quoc Cuong,
• Cao Hong Ha,
• Nguyen Ba Lam and
• Seiichi Kawahara

Beilstein J. Nanotechnol. 2024, 15, 168–179, doi:10.3762/bjnano.15.16

• after drying the solution in a heating oven. Vinyltriethoxysilane was used to modify GO [25][32] and it was bonded on the GO surface by the sol–gel method, as shown in Figure 1. Firstly, GO (0.4 g) was thoroughly dispersed in distilled water. After that, VTES (1.8 g) was added to the mixture, followed

A visible-light photodetector based on heterojunctions between CuO nanoparticles and ZnO nanorods

• Doan Nhat Giang,
• Nhat Minh Nguyen,
• Duc Anh Ngo,
• Thanh Trang Tran,
• Le Thai Duy,
• Cong Khanh Tran,
• Thi Thanh Van Tran,
• Phan Phuong Ha La and
• Vinh Quang Dang

Beilstein J. Nanotechnol. 2023, 14, 1018–1027, doi:10.3762/bjnano.14.84

• ) solution in an oven at 95 °C within 3 h (as presented in Supporting Information File 1, Figure S1). CuO NPs were synthesized via a simple and low-cost sol–gel method. At first, a mixture of 1.21 g Cu(NO3)2·5H2O and 0.8 g NaOH was dissolved in 50 mL deionized water under constant stirring at room

Upscaling the urea method synthesis of CoAl layered double hydroxides

• Camilo Jaramillo-Hernández,
• Víctor Oestreicher,
• Martín Mizrahi and
• Gonzalo Abellán

Beilstein J. Nanotechnol. 2023, 14, 927–938, doi:10.3762/bjnano.14.76

• ], sol–gel methods [26], mechanochemistry [27], or the epoxide route [28], to name a few [29]. Among them, hydrothermal methods based on ammonium-releasing reagents (ARRs), commonly urea or hexamethylenetetramine, are especially interesting since they allow one to obtain large and highly crystalline

Nanoarchitectonics to entrap living cells in silica-based systems: encapsulations with yolk–shell and sepiolite nanomaterials

• Celia Martín-Morales,
• Jorge Fernández-Méndez,
• Pilar Aranda and
• Eduardo Ruiz-Hitzky

Beilstein J. Nanotechnol. 2023, 14, 522–534, doi:10.3762/bjnano.14.43

• sol–gel methods, as well as pre-synthesised yolk–shell bionanohybrids have been studied subsequently. Optical microscopy and SEM confirm that the silica shell microstructures provide a reduced contact between cells. The inorganic matrix increases the survival of the cells and maintains their

• , by inorganic components generated by sol–gel processes from silicon alkoxides is an illustrative example of biohybrids that display the extraordinary functionality inherent to the assembled living components. For instance, bacteria such as Escherichia coli maintain their metabolic activity entrapped

• precursor could be cast and gelled as thin films or hollow tubular monoliths with thin walls, improving the interaction between the encapsulated cells and a liquid medium in which the material could be placed. In addition to the optimisation of the sol–gel synthesis, the conditions for yolk–shell

Bismuth-based nanostructured photocatalysts for the remediation of antibiotics and organic dyes

• Akeem Adeyemi Oladipo and
• Faisal Suleiman Mustafa

Beilstein J. Nanotechnol. 2023, 14, 291–321, doi:10.3762/bjnano.14.26

• techniques have been developed to synthesise 3-D Bi-based nanostructures with different morphologies, including solvothermal/hydrothermal and sol–gel processes, mechanical exfoliation, solid-state reactions, chemical vapour deposition, and microwave-assisted techniques [106]. These 3-D photocatalysts have

• . The final product might have some impurities, relatively large particles, and only a small degree of homogeneity. Large volumes of nanopowder can be produced using a relatively simple apparatus via solid-state routes. Wet-chemical methods (such as electrospinning, sol–gel, hydrothermal, ultrasound, co

• pure Bi2WO6 (82.8%), the dopant significantly increased the tetracycline-degrading activity, which reached 94.6% within 1 h of visible light irradiation. Additionally, Irfan et al. [148] used a bi-solvent sol–gel technique to synthesise porous bismuth ferrite nanostructures with various morphological

Antimicrobial and mechanical properties of functionalized textile by nanoarchitectured photoinduced Ag@polymer coating

• Jessica Plé,
• Marine Dabert,
• Helene Lecoq,
• Sophie Hellé,
• Lydie Ploux and
• Lavinia Balan

Beilstein J. Nanotechnol. 2023, 14, 95–109, doi:10.3762/bjnano.14.11

• difficult to implement and tend to cause NP self-aggregation. In situ methods are therefore generally preferred and typically require the polymer film surface to be treated with a metal precursor solution (layer-by-layer [37][38], sol–gel [39]) before undergoing thermal [40] or chemical reduction reactions

A TiO₂@MWCNTs nanocomposite photoanode for solar-driven water splitting

• Anh Quynh Huu Le,
• Ngoc Nhu Thi Nguyen,
• Hai Duy Tran,
• Van-Huy Nguyen and
• Le-Hai Tran

Beilstein J. Nanotechnol. 2022, 13, 1520–1530, doi:10.3762/bjnano.13.125

• ) nanocomposite by sol–gel method for visible-light-induced photocatalytic hydrogen evolution [8]. The photocatalyst consisted of dense TiO2 particles covering functionalized MWNTs and exhibited good photoactivity under visible light (λ > 420 nm), but the photoelectrochemical water splitting showed a low hydrogen

• nanocomposites as photoanode material for photoelectrochemical water splitting. Furthermore, the preparation of TiO2/MWCNTs nanocomposite derived from TiO2 precursors and functionalized MWCMTs for photoelectrochemical water splitting is based on complicated and time-consuming hydrothermal and sol–gel methods

• , in which the TiO2 particles are uniformly attached to CNTs by layer-by-layer coating or sol–gel methods [15][16][17]. Notably, the defects on the wall surface of MWCNTs, which enable π–π interactions, could be the active sites to generate the TiO2 agglomerations via hydroxy groups and, thus, enhance

Hydroxyapatite–bioglass nanocomposites: Structural, mechanical, and biological aspects

• Olga Shikimaka,
• Mihaela Bivol,
• Bogdan A. Sava,
• Marius Dumitru,
• Christu Tardei,
• Beatrice G. Sbarcea,
• Daria Grabco,
• Constantin Pyrtsac,
• Daria Topal,
• Andrian Prisacaru,
• Vitalie Cobzac and
• Viorel Nacu

Beilstein J. Nanotechnol. 2022, 13, 1490–1504, doi:10.3762/bjnano.13.123

• (HA), obtained by precipitate (HAP) and sol–gel (HAG) methods, and a boro-silico-phosphate bioglass. The microstructure and chemical, mechanical, and biological properties as functions of three factors, namely (i) the type of hydroxyapatite, (ii) glass content, and (iii) sintering temperature, were

• one hand, it induces antibacterial activity, and, on the other hand, it promotes the formation and mineralization of bone tissue [19][32]. The HA-BG composites investigated in this work contained two types of HA, obtained either by the sol–gel method (HAG) or by the precipitation method (HAP). It was

• composites The composite samples were obtained from hydroxyapatite prepared by a precipitation method (HAP) or by a sol–gel method (HAG) combined with a bioglass of definite composition. For the preparation of HAP powder we used the method described in a previous work [35] with small modifications, according

Structural studies and selected physical investigations of LiCoO₂ obtained by combustion synthesis

• Monika Michalska,
• Paweł Ławniczak,
• Tomasz Strachowski,
• Adam Ostrowski and
• Waldemar Bednarski

Beilstein J. Nanotechnol. 2022, 13, 1473–1482, doi:10.3762/bjnano.13.121

• produced in the form of powders, fibers, and films by using various processing techniques including wet chemical synthesis, such as the sol–gel method [33][34][35], precipitation [36], hydrothermal [37][38][39] and spray pyrolysis [40][41]. Also, solid-state synthesis methods, such as mechanical synthesis

Recent trends in Bi-based nanomaterials: challenges, fabrication, enhancement techniques, and environmental applications

• Vishal Dutta,
• Ankush Chauhan,
• Ritesh Verma,
• C. Gopalkrishnan and
• Van-Huy Nguyen

Beilstein J. Nanotechnol. 2022, 13, 1316–1336, doi:10.3762/bjnano.13.109

Studies of probe tip materials by atomic force microscopy: a review

• Ke Xu and
• Yuzhe Liu

Beilstein J. Nanotechnol. 2022, 13, 1256–1267, doi:10.3762/bjnano.13.104

• new probe preparation method based on gold and silver nanowire optical waveguides, which uses the direct coupling of optical fiber and gold and silver optical waveguides to prepare the tip, synthesizes gold or silver nanowires by sol-gel method, etches the hollow optical fiber or pulls the cone by

Design of surface nanostructures for chirality sensing based on quartz crystal microbalance

• Yinglin Ma,
• Xiangyun Xiao and
• Qingmin Ji

Beilstein J. Nanotechnol. 2022, 13, 1201–1219, doi:10.3762/bjnano.13.100

• -TiO2 nanofibers by using N-stearoyl- ʟ/ᴅ-glutamic acid (C18-ʟ/ᴅ-Glu) lipid as the chiral template and titanium diisopropoxide bis(acetylacetonate) as the titanium source based on a sol–gel process [119]. The average length and width of the TiO2 nanofiber were ca. 200 and 30 nm, respectively. The

Application of nanoarchitectonics in moist-electric generation

• Jia-Cheng Feng and
• Hong Xia

Beilstein J. Nanotechnol. 2022, 13, 1185–1200, doi:10.3762/bjnano.13.99

• , photolithography, embossing, deposition, and sol–gel nanofabrication, all of which can provide high specific surface areas [19][24][25][26][27][28]. Nanomaterials can also be divided into inorganic nanomaterials and organic nanomaterials. In inorganic nanomaterials, metal nanomaterials and carbon nanomaterials

Green synthesis of zinc oxide nanoparticles toward highly efficient photocatalysis and antibacterial application

• Vo Thi Thu Nhu,
• Nguyen Duy Dat,
• Le-Minh Tam and
• Nguyen Hoang Phuong

Beilstein J. Nanotechnol. 2022, 13, 1108–1119, doi:10.3762/bjnano.13.94

• . Lack of information regarding this application has been reported. This is the motivation for this study which is focused on synthesizing nanosized ZnO materials by the sol–gel method using rosin as a green precursor. ZnO NPs were synthesized by a sol–gel two-step method from the green precursor rosin

Biomimetic chitosan with biocomposite nanomaterials for bone tissue repair and regeneration

• Se-Kwon Kim,
• Sesha Subramanian Murugan,
• Pandurang Appana Dalavi,
• Sebanti Gupta,
• Sukumaran Anil,
• Gi Hun Seong and
• Jayachandran Venkatesan

Beilstein J. Nanotechnol. 2022, 13, 1051–1067, doi:10.3762/bjnano.13.92

• silsesquioxane, chitosan–nanoSiO2–chondroitin sulphate, chitosan–nanoSiO2–gelatin, and chitosan–bioglass/hydroxyapatite/halloysite nanotubes have remarkable osteogenic characteristics [82][83][84][123]. Chitosan and silica-based microspheres were produced by using sol–gel followed by emulsification and cross

Solar-light-driven LaFe_xNi_1−xO₃ perovskite oxides for photocatalytic Fenton-like reaction to degrade organic pollutants

• Chao-Wei Huang,
• Shu-Yu Hsu,
• Jun-Han Lin,
• Yun Jhou,
• Wei-Yu Chen,
• Kun-Yi Andrew Lin,
• Yu-Tang Lin and
• Van-Huy Nguyen

Beilstein J. Nanotechnol. 2022, 13, 882–895, doi:10.3762/bjnano.13.79

• ), Chengalpattu district, Kelambakkam, Tamil Nadu, 603103, India 10.3762/bjnano.13.79 Abstract LaFexNi1−xO3 perovskite oxides were prepared by the sol–gel method under various conditions, including different pH values (pH 0 and pH 7) and different calcination temperatures (500–800 °C) as well as different Fe/Ni

• nanoparticles via the sol–gel method to decompose rhodamine-B under visible light irradiation. With the assistance of H2O2, it shows a synergistic effect between photocatalytic reaction and heterogeneous photo-Fenton-like reaction [23]. Furthermore, the strategies of being loaded over supports (such as g-C3N4

• sol–gel solution could help the separation of LaFexNi1−xO3 crystals, leading to less particle aggregation. Moreover, the elemental analysis of the samples was also carried out using energy dispersive spectroscopic (EDS). The Fe contents of the samples with different Fe/Ni atomic ratios were identified

Hierarchical Bi₂WO₆/TiO₂-nanotube composites derived from natural cellulose for visible-light photocatalytic treatment of pollutants

• Zehao Lin,
• Zhan Yang and
• Jianguo Huang

Beilstein J. Nanotechnol. 2022, 13, 745–762, doi:10.3762/bjnano.13.66

• deposited onto cellulose nanofiber templates by the surface sol−gel method according to a previous report (Figure 1a, Figure 1b) [31]. The as-prepared TiO2-gel/cellulose-fiber composite was calcined in air at 450 °C (heating rate: 1 °C/min) for 6 h to give the hierarchical structure of TiO2 nanotubes

• pure TiO2-NT sample without any of the subsequent treatments. The Bi2WO6 powder sample was fabricated by the same solvothermal reaction without the addition of the powder containing hierarchical TiO2 nanotubes. The TiO2 sample without the cellulose template was prepared by the simple sol−gel method

• nanocomposites were fabricated by depositing Bi2WO6 nanoparticles onto the hierarchical TiO2 tubes via the solvothermal method, where the TiO2 tubes were obtained by the calcination of the TiO2-gel/cellulose composite, which in turn was prepared through the surface sol−gel method. According to the theoretical

Zinc oxide nanostructures for fluorescence and Raman signal enhancement: a review

• Ioana Marica,
• Fran Nekvapil,
• Maria Ștefan,
• Cosmin Farcău and
• Alexandra Falamaș

Beilstein J. Nanotechnol. 2022, 13, 472–490, doi:10.3762/bjnano.13.40

• methods used for obtaining ZnO nanoparticles, solution synthesis methods such as sol–gel [22], chemical precipitation [23], polyol [24], and solvothermal [25] methods, are inexpensive, consume little energy, allow for a facile control of physical characteristics and morphology of the nanoparticles, offer

• ) [12] was carried out as well. Chou et al. employed a simple and rapid method, namely pulsed laser-induced photolysis to develop Au NPs on the surface of ZnO nanorods fabricated by the sol–gel method (Figure 2c,d) [38]. Various irradiation times were tested, indicating that a short irradiation time was

• morphology for SERS measurements can be fabricated using various methods, including sol–gel synthesis [38], thermal deposition [31][32], chemical vapour deposition [42], or electrodeposition [35], which resulted in 1.2 μm high, vertically aligned nanorods of 60 nm diameter. It was observed that thermal

Micro- and nanotechnology in biomedical engineering for cartilage tissue regeneration in osteoarthritis

• Zahra Nabizadeh,
• Mahmoud Nasrollahzadeh,
• Hamed Daemi,
• Mohamadreza Baghaban Eslaminejad,
• Ali Akbar Shabani,
• Mehdi Dadashpour,
• Majid Mirmohammadkhani and
• Davood Nasrabadi

Beilstein J. Nanotechnol. 2022, 13, 363–389, doi:10.3762/bjnano.13.31

• as potential candidates for bone TE due to osteoblast attachment and corrosion resistance [141]. Wan et al. used bacterial cellulose as a template to synthesize calcined mesoporous TiO2 nanotubes and constructed a nanotube-based scaffold using a template-assisted sol–gel method [142]. In addition to

Tin dioxide nanomaterial-based photocatalysts for nitrogen oxide oxidation: a review

• Viet Van Pham,
• Hong-Huy Tran,
• Thao Kim Truong and
• Thi Minh Cao

Beilstein J. Nanotechnol. 2022, 13, 96–113, doi:10.3762/bjnano.13.7

• of Sn at the surface of SnO2 plays a role in the reversible transformation of the surface composition from Sn4+ cations to Sn2+, which leads to active centers in the surface chemical process [48]. Moreover, the OVs in SnO2 often appear when it is synthesized by chemical methods such as sol–gel

• materials, preferably using two redox sites; (3) synthesizing other morphologies of SnO2 such as nanorods, nanotubes, or 3D structures to increase the specific surface area of the catalyst; (4) upscaling the syntheses and using other synthesis approaches such as sol–gel or chemical vapor deposition to form

Sputtering onto liquids: a critical review

• Anastasiya Sergievskaya,
• Adrien Chauvin and
• Stephanos Konstantinidis

Beilstein J. Nanotechnol. 2022, 13, 10–53, doi:10.3762/bjnano.13.2

Morphology-driven gas sensing by fabricated fractals: A review

• Vishal Kamathe and
• Rupali Nagar

Beilstein J. Nanotechnol. 2021, 12, 1187–1208, doi:10.3762/bjnano.12.88

• are used as sensing material [57]. Proposed growth model for fab-fracs This section specifically discusses the various parameters that influence the final shape of a lab-grown fab-frac using the sol–gel technique. Nucleation is a random and probabilistic event that happens on a substrate. As a fluid

• to some excellent articles on hierarchical gas sensors that address such geometries [8][30][33][37]. Tin oxide-based fractals Yin et al. reported SnO2 nanoparticles with and without platinum (Pt) decoration synthesized using a sol–gel hydrothermal technique for gas sensing applications [63]. Figure

• geometry. Plugotarenko et al. employed sol–gel method to prepare SiO2·SnOx·CuOy nanofilms from a tetraethoxysilane (TEOS) alcohol solution modified by metal salts and applied the samples for NO2 sensing [50]. The SiO2·SnOx·CuOy films annealed at 500 °C exhibited a sample surface consisting of crater-like

Comprehensive review on ultrasound-responsive theranostic nanomaterials: mechanisms, structures and medical applications

• Sepand Tehrani Fateh,
• Lida Moradi,
• Elmira Kohan,
• Michael R. Hamblin and
• Amin Shiralizadeh Dezfuli

Beilstein J. Nanotechnol. 2021, 12, 808–862, doi:10.3762/bjnano.12.64

Solution combustion synthesis of a nanometer-scale Co₃O₄ anode material for Li-ion batteries

• Monika Michalska,
• Huajun Xu,
• Qingmin Shan,
• Shiqiang Zhang,
• Yohan Dall'Agnese,
• Yu Gao,
• Amrita Jain and
• Marcin Krajewski

Beilstein J. Nanotechnol. 2021, 12, 424–431, doi:10.3762/bjnano.12.34

• been proposed including sol–gel methods [4][6][13][14][15], sol–electrospinning techniques [16][17][18][19], hydrothermal and solvothermal syntheses [20][21][22][23][24][25][26][27][28], precipitation and co-precipitation [29][30][31], chemical thermal decomposition and pyrolysis [32][33][34][35][36

Structural and optical characteristics determined by the sputtering deposition conditions of oxide thin films

• Petronela Prepelita,
• Florin Garoi and
• Valentin Craciun

Beilstein J. Nanotechnol. 2021, 12, 354–365, doi:10.3762/bjnano.12.29

• dielectric properties (e.g., SiO2 and ZnO) exhibit a dependence of the electrical resistance with temperature [22][23]. SiO2 and ZnO films are obtained by various deposition techniques, such as matrix-assisted pulsed laser evaporation (MAPLE) [24][25], spin coating of sol–gel precursor solutions [26], radio