The 2013 Impact Factor is 2.326 according to the Thomson Reuters Journal Citation Reports.


Registration is now open for the Beilstein Nanotechnology Symposium 2014.

 
 

k-space imaging of the eigenmodes of sharp gold tapers for scanning near-field optical microscopy

Martin Esmann1,2, Simon F. Becker1,2, Bernard B. da Cunha1,2, Jens H. Brauer1,2, Ralf Vogelgesang1,2, Petra Groß1,2 and Christoph Lienau1,2
1Institut für Physik, Carl von Ossietzky Universität, 26129 Oldenburg, Germany
2Center of Interface Science, Carl von Ossietzky Universität, 26129 Oldenburg, Germany
Email of corresponding author Corresponding author email     
This article is part of the Thematic Series "Optical near-fields & nearfield optics".
Guest Editors: A. J. Meixner and P. Leiderer
Beilstein J. Nanotechnol. 2013, 4, 603–610.
doi:10.3762/bjnano.4.67
 
 
 
 

Abstract

We investigate the radiation patterns of sharp conical gold tapers, which were designed as adiabatic nanofocusing probes for scanning near-field optical microscopy (SNOM). Field calculations show that only the lowest order eigenmode of such a taper can reach the very apex and thus induce the generation of strongly enhanced near-field signals. Higher-order modes are coupled into the far field at finite distances from the apex. Here, we demonstrate experimentally how to distinguish and separate between the lowest and higher-order eigenmodes of such a metallic taper by filtering in the spatial frequency domain. Our approach has the potential to considerably improve the signal-to-background ratio in spectroscopic experiments at the nanoscale.

Keywords: adiabatic nanofocusing; Fourier optics; metallic wire modes; plasmonics; scanning near-field optical microscopy (SNOM)

Top

Introduction

Metallic nanostructures support collective oscillations of the electron gas, which couple strongly to light. At extended metal–dielectric interfaces, the resulting surface-bound modes, termed surface plasmon polaritons (SPPs), may propagate along the interface. At geometric singularities, i.e., in regions of deep-subwavelength radius of curvature, these modes tend to be spatially confined and are called localized surface plasmons (LSPs). During recent years, experimental realizations of SPP guiding in sub-wavelength dimensions [1] and the transformation of propagating SPPs into LSPs have drawn tremendous attention within the field of plasmonics. The concept of SPP to LSP transformation has been investigated theoretically and experimentally for different metal nanostructures [2-5] in both the adiabatic [5-7] and the non-adiabatic [8] limit. Theoretically, it has been shown to be particularly promising in its adiabatic limit, i.e., for waveguides with gradually (adiabatically) varying cross-section, for which reflection-free SPP propagation and efficient transformation are predicted [6]. This gives rise to a new class of probes in apertureless scanning near-field optical microscopy (SNOM) that focus light down to volumes well below the classical diffraction limit [5,6]. In particular, it has been predicted that SPP wavepackets may be localized both in space and time when they are launched onto a tapered metallic waveguide, e.g., a conical tip with a nanometer-sized apex and sufficiently small opening angle [6]. This formation of a strongly confined lightspot is now termed “adiabatic nanofocusing” [6]. The expected nanometer-scale confinement offers the possibility to efficiently couple light into a single nanoobject, making such probes highly attractive for inherently background-free, new spectroscopic applications on the nanometer scale.

Adiabatic nanofocusing has been demonstrated experimentally by grating-coupling of light to SPPs on electrochemically etched gold tapers [9]. Such tapers have been incorporated in SNOM setups and nanostructures such as a single gold nanoparticle [10,11] or silicon step edge [12] have been imaged, demonstrating an optical resolution of down to 10 nm. Moreover, time-resolved studies showed that the time structure of ultra-fast laser pulses in the few-femtosecond regime hardly changes upon grating coupling to SPPs and during propagation over distances of several tens of microns on the surface of a gold taper [11]. These results have been confirmed by three-dimensional finite difference time domain (FDTD) simulations [11]. These theoretical investigations and experimental demonstrations suggest that pump–probe studies employing adiabatic nanofocusing are well within experimental reach.

Despite its large potential, adiabatic nanofocusing has not yet been established as a standard approach to optical investigations on the nanoscale. Arguably, the most critical challenge is reproducibility. Taper probes produced by electrochemical etching as described in [11] differ drastically in their conversion efficiency from far-field radiation to nano-localized LSP intensity at the apex. The differences in conversion efficiency exist even for tips having nominally identical, smooth surfaces, appropriate opening angles and small apex radii. Therefore, experiments are time consuming and high quality data are scarce. Scanning electron micrographs of two conical taper probes that were used in our own experiments are shown in Figure 1. Whereas their geometry and morphology appear very similar, they showed very different conversion efficiencies.

[2190-4286-4-67-1]
Figure 1: Scanning electron micrographs of two gold tapers that were obtained by electrochemical AC-etching of annealed gold wires followed by focused ion beam milling of the grating couplers. Field enhancement at the taper apex was much more pronounced for the tip shown in panel a).

Conceptually, the difference in conversion efficiency may be explained as a mode matching problem. When employing a grating coupler to excite SPPs, as done, e.g., in [9-12], different eigenmodes of the taper are excited. Their relative amplitudes are given by their spatial overlap with the incoming field and depend critically upon the exact shape of the tip and the incoming phase front. Theoretical studies have shown that only the lowest, rotationally symmetric eigenmode is nanofocused down to the very apex of the tip [13] where it gets highly confined. In contrast, higher order modes radiate into the far-field while propagating along the taper. This far-field coupling can occur within the last micron from the tip apex, making it difficult to distinguish these modes from the nano-localized LSP fields. This hampers efficient background-free nanofocusing with the setup described in [10] and higher order mode suppression remains an unsolved challenge.

In this work we present the first steps toward overcoming this challenge. Our approach seeks to provide direct access to the field distribution in the vicinity of the taper apex. To this end, we apply k-space imaging of the fields emitted from the taper apex. By analyzing the rotational symmetry of the resulting radiation patterns we are able to distinguish between contributions from eigenmodes of different orders. In effect, this opens up new possibilities for optimizing the relative contribution from the lowest mode as well as extracting the near-field contributions at the taper apex. We think that this is an important step toward ultrafast pump–probe spectroscopy on the nanoscale. Specifically, we show that we can differentiate between the zeroth and first order mode, which is generally difficult when using conventional far field imaging techniques.

Top

Eigenmodes of a tapered wire

In order to describe the process of linear SPP propagation on the SNOM probe in the framework of classical electrodynamics, it is useful to expand the SPP wavepacket in terms of orthonormal eigenmodes at any point along the waveguide. The concept of adiabatic nanofocusing assumes that the diameter of a tapered waveguide varies only slowly over the distance of one wavelength of the guided SPP. Therefore, a proper local set of eigenmodes is well approximated by the eigenmodes of an infinitely long waveguide having the local diameter of the taper. For a cylindrical metal wire surrounded by a homogeneous dielectric, these solutions are the well-known wire modes [14-16]. These modes possess a discrete rotational symmetry with respect to the angle φ of a cylindrical coordinate system whose z-axis coincides with the wire axis. The symmetry is governed by a quantization number n, corresponding to an angular momentum, which manifests itself in a field distribution of the form [Graphic 1]. The propagation of the wire modes is described by a transcendental equation, which can be derived from Maxwell’s equations and the appropriate boundary conditions at the metal–dielectric interface [13-16]. It yields the propagation constant kz along the tapered wire as a function of the dielectric material properties, the wire radius, and the frequency of the SPP mode.

Based on this approach we have numerically calculated the propagation constant for a gradually decreasing wire radius, R. The results for the SPP frequency corresponding to a vacuum wavelength of 800 nm on a gold wire (dielectric constant ε1 = −24.7470 + 1.8834i, which was obtained by fitting experimental data from [17]) surrounded by air (ε2 = 1) are displayed in Figure 2.

[2190-4286-4-67-2]
Figure 2: Propagation constants kz of the three lowest eigenmodes of an infinitely long gold wire as a function of wire radius R. Displayed are the real (solid blue lines) and imaginary (dotted red lines) parts of kz pointing along the taper axis for angular momenta n = 0,1,2 (panels a)–c)). The SPP frequency corresponds to a vacuum wavelength of 800 nm, as used in the experiment. For n = 0, both Re(kz) and Im(kz) diverge for small radii. For n = 1, kz approaches the light line, k0 = ω/c0, for small radii. A cutoff behavior at approximately 600 nm is observed for n = 2. Panel d) summarizes these findings and schematically illustrates the mode profiles.

For decreasing radii, the three lowest modes n = 0,1,2 (cf. Figure 2, panels a)–c)) behave distinctly different. For the lowest, rotationally symmetric mode with n = 0, both the real and imaginary part of the propagation constant are divergent for a vanishing wire radius. Thus, this mode remains strongly bound to the interface while its wavelength shortens, leading to a decrease in SPP group velocity. In effect, the SPP is transformed into a strongly confined LSP. In the region below the tip, the field emitted by this LSP mode closely resembles that of an oscillating point dipole [18,19]. In the case of a tapered waveguide, the corresponding dipole moment is oriented along the taper axis. Hence, the field as well as the radiation pattern emerging from the apex maintain the rotational symmetry of the eigenmode.

In contrast, for the n = 1 mode, the propagation constant approaches the light line, k0 = ω/c0, for radii of about 70 nm, indicating that the mode looses its bound character. It is not transformed into a highly confined LSP at the taper end and we therefore refer to it as a loosely bound photonic mode. The third mode, with n = 2, already displays a cut-off behavior for a radius only slightly above 600 nm. This mode is not sustained on the wire for smaller radii. The same is true for all higher order modes.

As a consequence, only the n = 0 and n = 1 eigenmodes of the wire are expected to contribute to near-fields in the vicinity of the taper apex. When scattered into the far-field, the contributions of those two modes cannot be distinguished by using only far-field optics, as their spatial separation is well below the classical diffraction limit. When using tapered nanofocusing probes in a SNOM setup, only the n = 0 eigenmode generates the desired, spatially highly resolved signal, containing information about the sample properties on the nanoscale. The n = 1 mode, however, is expected to contribute to a non-negligible background signal due to its weak confinement.

Top

Experimental setup

Our experimental setup used for k-space imaging is sketched in Figure 3. The field distribution at the apex of the taper is probed by placing it in front of a gold-coated dielectric surface that couples some fraction of the evanescent near-fields at the apex to propagating far-field modes. The angular distribution of these propagating waves is measured with an immersion objective. In the following, we describe the individual parts of the experimental setup.

[2190-4286-4-67-3]
Figure 3: Setup for k-space imaging of radiation emitted from the apex of a sharp gold taper. SPP wavepackets launched via a grating coupler are adiabatically nanofocused. A gold-coated cover slip is brought into close proximity of the taper. Light scattered through the cover slip is collected with a high numerical aperture objective (NA = 1.3). The spatial Fourier transform of light in the front focal plane is imaged from the back focal plane of the objective onto a CCD camera. A spatial filter is applied in the intermediate real image plane.

Tapers as shown in Figure 1 are produced from single-crystalline gold wire by an electrochemical AC-etching technique followed by focused ion beam milling of a grating coupler [11]. Typical cone opening angles are between 20 and 30° and apex radii are well below 30 nm. These tips have a very smooth surface and accordingly high SPP propagation lengths as reported earlier [11]. To excite SPPs on the probe, we use a pulsed titanium sapphire (Ti:Sa) laser source operating at a central wavelength of 800 nm and featuring a 10 nm wide Gaussian spectral distribution. This light is focused onto the grating coupler with a microscope objective (NA = 0.1), applying an average power of 200 μW at a repetition rate of 80 MHz. The SPP wavepacket launched on the coupler propagates toward the taper apex.

The light emitted from the taper apex is then transmitted through a 20 nm thick gold film on a cover slip. The main reason for using a Au-coated sample was to enhance the evanescent light contributions to the k-space images. The gold film has three major effects on those images. (i) It substantially suppresses the transmission of propagating waves ([Graphic 2] < k0, allowed light), which have to tunnel through the film. For our film, we measure that the transmission is reduced to about 20%. (ii) It enhances the total power radiated into forbidden light modes by about a factor of 2, as can be seen from a simple estimate based on a point dipole model (see., e.g., [20], Ch. 10). (iii) Most importantly, it allows us to probe the near-field coupling between the tip dipole, i.e., the near fields at the tip apex, and its image dipole induced in the metal (see [21,22]).

The light transmitted through the gold-coated cover slip is collected using an oil immersion objective with high numerical aperture (NA = 1.3, Olympus UPlanFLN 100×). The tip-apex position lies within the focal plane of the microscope objective. In this configuration, the objective performs a Fourier transform of the field distribution from the front into the back focal plane. Two additional lenses with focal lengths of f1 = 150 mm and f2 = 100 mm, respectively, image the back focal plane onto a CCD camera (Thorlabs DCC1545M-GL) in a 4f-configuration. In the intermediate real image plane, the filtering of scattered light from the grating coupler is realized with an iris aperture.

The distance between probe and cover slip is controlled using a tuning fork-based force sensor in a noncontact-mode atomic force microscope (AFM). This microscope is a modified version of the setup described in [10]. The taper probe is attached to one prong of a quartz tuning fork that oscillates with a peak-to-peak amplitude of 1 nm. The cover slip is mounted onto a three-axis piezoelectric stage (PI P-363.3CD). This allows us to slowly approach the sample to the taper over a distance of several hundreds of nanometers in steps of 30 pm until the tuning fork starts to be damped by tip–sample interactions. The damping occurs on a length scale of less than 5 nm. The sample is subsequently retracted to its original position with the same step size. While recording force-approach curves, the CCD camera is triggered to capture the respective k-space images for selected positions on the approach curve.

Top

Results

We have recorded distance-dependent k-space images of the light transmitted through the gold-coated cover slip for several grating-coupler type nanofocusing tapers. The results of a representative experiment for the taper shown in Figure 1a are described in detail in the following. A sequence of camera images was recorded at selected positions on the AFM approach curve. The first frame of this sequence taken at a tip–sample spacing of about 150 nm is displayed in Figure 4a. In this image, the bright pattern (labeled position i) corresponds to radiation from the far-field with in-plane k-vectors [Graphic 2] smaller than k0 = ω/c0. The ring-like pattern (labeled ii) is associated with in-plane k-vectors [Graphic 2] slightly larger than k0. It can be attributed to leakage radiation from SPPs excited on the gold film [23-25]. The dark area outside the larger dashed circle (labeled iii) reflects in-plane k-vectors [Graphic 2] larger than 1.3 · k0, which are not captured by our oil immersion objective. The area between the two dashed circles (labeled iv) is thus the region of interest (ROI) to us. Here, only forbidden light [24] originating from evanescent fields at the taper apex is detected.

[2190-4286-4-67-4]
Figure 4: k-space patterns recorded while approaching a gold-coated cover slip to the SNOM probe. Tip-sample spacings are indicated in the lower right corner of the respective images and the corresponding pictographs in the lower left corner. Panel a) shows raw data, the dashed circles mark the region of interest (ROI, labeled iv). Panels b)-g) represent the evolution of the k-space pattern during approach. For clarity, the data are limited to the ROI and are rescaled to the 90th percentile of all pixel intensities within the ROI in panel g).

Panels b)–g) of Figure 4 show a sequence of six camera images with equidistant spacing along the corresponding AFM approach curve. For clarity, they exclusively depict the ROI and the intensities have been rescaled. The red arrow in panel g) marks a short-ranged increase in intensity, which is only visible in this panel. A video file of the image sequence is available as Supporting Information File 1.

A quantitative analysis of the full sequence of images is displayed in Figure 5. It has been obtained by radially integrating across the ROI for each position on the approach curve. The resulting integrated intensities are plotted as a function of in-plane angle φ and tip–sample spacing d. To improve the comparability and to simplify the identification of the individual features, each horizontal line, corresponding to a fixed angle φ, was normalized to its maximum after subtraction of its first value during approach (at d = 150 nm). The color bar has been restricted to the range from zero to one. Similar plots have been generated from measurements at different spatial positions on our gold film. Within our signal-to-noise ratio, the data show no variation with sample position. This suggests that the possible excitation of localized surface plasmon fields on the gold film has only a very limited effect on our experimental data and supports that our experiments indeed map the emission properties of the nanotaper.

[2190-4286-4-67-5]
Figure 5: Quantitative analysis of the evolution of k-space patterns during tip approach and retraction. Panel a) shows the angular intensity distribution, radially integrated across the ROI (cf. Figure 4a), as a function of tip–sample spacing. At each angle, the data have been normalized. The region between the two dashed white lines has been averaged with respect to the angle and the data have been plotted in panel b) together with an exponential fit to the part of the data recorded during approach. The decay length is 14 nm. Here, the data have been normalized to the background signal. The inset shows an equal set of data for a different angular region around 110°.

Two qualitatively different decay lengths emerge from these plots. One of them is well below 30 nm and appears most prominently at polar angles around 225°. This area is marked by the red arrow in Figure 4g. The other, much longer decay length occurs in two opposing lobes above and below the region marked by the two dashed white lines. These two different decay lengths have also been observed qualitatively in experiments performed with other tapers. To quantify the short decay length for the given tip, the data inside the marked zone in Figure 5a have been integrated azimuthally. For comparison this has also been done with the data between 100 and 120°. The integrated values are plotted in panel b) and the inset therein, respectively. In this panel, the offset at d = 150 nm was not subtracted and was used for normalization to it such that the y-axis gives the relative increase with respect to this offset. An exponential fit to the data points taken during approach (open red squares), offset by 1.0, has been added. The corresponding decay length is 14 nm and the overall increase in intensity amounts to a factor of five.

Top

Discussion

The angular decay spectrum displayed in Figure 5a strongly suggests that only those SPP fields that are coupled to the lowest order and first higher order eigenmodes of the taper, propagate as bound modes into close proximity of the taper apex. This is qualitatively understood in the following way: The symmetry of the n = 1 mode is that of an in-plane dipole with its dipole moment oriented parallel to the sample surface. Thus, its angular radiation distribution should exhibit two opposing lobes. These lobes are clearly seen in Figure 5a in the quadrants ranging from 90 to 180° and 270 to 360°, respectively. The decay length observed in these two lobes agrees with the expectation for the evanescent decay in air related to the in-plane k-vector components [Graphic 2] within the ROI.

For the eigenmode with n = 0 a rotationally symmetric radiation pattern is expected for an ideally symmetric tip. Theoretically, it has been shown that the fields at the tip apex decay with a length slightly shorter than the apex radius [26-28]. Taking image charge effects into account [21,22], the decay in k-space closely resembles the behavior in real space. This short-ranged decay is most prominently encountered in the region marked with the dashed white lines in Figure 5a and the red arrow in Figure 4g. In this region, the line shape nicely follows an exponential decay as can be seen in Figure 5b. The decay length of 14 nm is in convincing agreement with the theoretical expectation. As determined by scanning electron microscopy, our tapers usually have apex radii between 10 and 20 nm. For the region between 0 and 50°, the measured total intensities are small. Therefore, the values obtained in this region should be considered with care.

Interference between the two modes with n = 0 and n = 1 is expected to give rise to constructive interference in one lobe and destructive interference in the other, resulting in an asymmetric distribution of the intensity in the two lobes as well. In Figure 4, an asymmetry in the intensity of the two opposing lobes is indeed observed. By comparison with the overall intensity detected from the n = 0 mode, however, it can be deduced that this effect still cannot fully account for the observed asymmetry.

As can be seen in Figure 4a, an asymmetric signature of surface plasmon polariton resonance leakage is also detected in the raw data (labeled ii). The tails of this resonance extend into that part of k-space that we define as the region of interest (ROI). A substantial amount of the asymmetry in the processed signal (visible in Figure 4bFigure 4g) can be attributed to this effect. The excitation of this resonance is most likely due to scattering of radiation from the grating coupler as well as emission from higher order modes of the taper. It is therefore possible that this spurious signal overlaps in our k-space images with the desired signatures from the n = 0 and n = 1 modes and thus contributes to the recorded asymmetry.

To give an estimate of the relative contributions of the n = 0 and n = 1 modes, we compare the intensities in our k-space images. The relative amplitude of the n = 0 and n = 1 mode-emission appears similar when approaching the surface. These k-space images probe evanescent fields within a finite wave vector range, extending to about 1.3 · k0. The k-space distribution of the (spatially highly confined) n = 0 mode extends to much larger k-vectors than that of the n = 1 mode. This k-spectrum is much broader than what is probed in our experiments. Hence only a fraction of the n = 0 mode emission can be detected. In high-resolution near-field experiments, however, the entire k-spectrum contributes.

Inside the two lobes with the long-ranged decay, a decrease of the intensity sets in for small values of the tip–sample spacing (see inset in Figure 5b). To account for this behavior, we believe that we need a near-field source that produces a field with a k-space symmetry similar to that of the n = 1 mode. Its field amplitude should vary substantially over the last 20 nm. Such fields would be generated by a laterally oriented dipolar emitter located near the tip apex. This dipole emission may reflect contributions of the n = 1 mode that are weakly guided towards the taper apex. Earlier FDTD simulations [29] indeed indicate that, for asymmetric grating-excitation on one side of the taper, as done in our experiments, the field near the apex is not just that of a point-like dipole oriented purely along the z-axis. Instead, a slightly asymmetric near-field near the tip apex is predicted. The formation of a laterally oriented dipole field is clearly observed in these simulations. We believe taking these effects into account can readily explain the interference effects observed in the two lobes in Figure 5a.

In view of the discussion above, the results presented in Figure 5a are well understood considering the emission from only the lowest two eigenmodes of the conical taper. Apparently, all higher order modes decouple from the taper already at distances of the order of one wavelength or above. Hence, they contribute only weakly to the recorded forbidden light images presented here. This suggests that k-space filtering is an efficient means for suppressing undesired background fields in adiabatic nanofocusing SNOM.

Top

Conclusion

In summary, we have presented a method to investigate the radiation patterns of adiabatic nanofocusing SNOM probes. Our experiments demonstrate that SPP fields coupled to the lowest two eigenmodes are efficiently funneled toward the taper apex. Most importantly, we show that the n = 0 eigenmode produces a spatially highly localized near-field at the apex, as predicted by theory, whereas the loosely bound n = 1 mode is much less confined. Their contributions are readily identified by analyzing the evolution of angular radiation patterns over the course of an approach curve. This opens up the possibility to separate the rapidly decaying n = 0 mode from the undesired higher modes by k-space filtering.

These findings form the basis for further improvements and novel applications. The rapidly decaying contribution to the k-space images provides a direct measure of the desired n = 0 mode. Hence, we can use this signal to optimize adiabatic nanofocusing into the lowest order mode. This minimizes background from higher order modes and thus provides a major advancement towards background-free scanning near-field optical spectroscopy. Since we are able to further separate the near-field contributions by k-space filtering, we can now apply this method to spectroscopic studies of the coupling between nano-localized fields and single quantum objects. Such experiments are currently underway in our laboratory.

Top

Supporting Information

Video compiled from k-space images taken during an approach curve. This is a full length sequence of the images shown in Figure 4.

Supporting Information File 1: Video of an approach curve
Format: AVI   Size: 9.0 MB   Download

Top

Acknowledgements

Financial support by the Deutsche Forschungsgemeinschaft (SPP1391 ‘Ultrafast Nanooptics’, DFG-Li860/5-1 and DFG-NSF Materials World Network), by the Korea Foundation for International Cooperation of Science and Technology (Global Research Laboratory Project K20815000003) and by the European Community through the CRONOS project, Grant Agreement No. 280879, is gratefully acknowledged. ME acknowledges funding from the Studienstiftung des Deutschen Volkes. We thank Heiko Kollmann for supporting the theoretical calculations, Kerstin Reiners and Marco Ohm for contributions at an early phase of this work and Raimond Angermann for continuous high quality technical support.

Top

References

  1. Gramotnev, D. K.; Bozhevolnyi, S. I. Nat. Photonics 2010, 4, 83–91. doi:10.1038/nphoton.2009.282
    Return to citation in text: [1]
  2. Aubry, A.; Lei, D. Y.; Fernández-Dominguez, A. I.; Sonnefraud, Y.; Maier, S. A.; Pendry, J. B. Nano Lett. 2010, 10, 2574–2579. doi:10.1021/nl101235d
    Return to citation in text: [1]
  3. Gramotnev, D. K. J. Appl. Phys. 2005, 98, 104302. doi:10.1063/1.2130520
    Return to citation in text: [1]
  4. Luo, Y.; Pendry, J. B.; Aubry, A. Nano Lett. 2010, 10, 4186–4191. doi:10.1021/nl102498s
    Return to citation in text: [1]
  5. Babadjanyan, A. J.; Margaryan, N. L.; Nerkararyan, K. V. J. Appl. Phys. 2000, 87, 3785–3788. doi:10.1063/1.372414
    Return to citation in text: [1] [2] [3]
  6. Stockman, M. I. Phys. Rev. Lett. 2004, 93, 137404. doi:10.1103/PhysRevLett.93.137404
    Return to citation in text: [1] [2] [3] [4] [5]
  7. Durach, M.; Rusina, A.; Stockman, M. I.; Nelson, K. Nano Lett. 2007, 7, 3145–3149. doi:10.1021/nl071718g
    Return to citation in text: [1]
  8. Issa, N.; Guckenberger, R. Plasmonics 2007, 2, 31–37. doi:10.1007/s11468-006-9022-7
    Return to citation in text: [1]
  9. Ropers, C.; Neacsu, C. C.; Elsaesser, T.; Albrecht, M.; Raschke, M. B.; Lienau, C. Nano Lett. 2007, 7, 2784–2788. doi:10.1021/nl071340m
    Return to citation in text: [1] [2]
  10. Sadiq, D.; Shirdel, J.; Lee, J. S.; Selishcheva, E.; Park, N.; Lienau, C. Nano Lett. 2011, 11, 1609–1613. doi:10.1021/nl1045457
    Return to citation in text: [1] [2] [3] [4]
  11. Schmidt, S.; Piglosiewicz, B.; Sadiq, D.; Shirdel, J.; Lee, J. S.; Vasa, P.; Park, N.; Kim, D.-S.; Lienau, C. ACS Nano 2012, 6, 6040–6048. doi:10.1021/nn301121h
    Return to citation in text: [1] [2] [3] [4] [5] [6] [7]
  12. Neacsu, C. C.; Berweger, S.; Olmon, R. L.; Saraf, L. V.; Ropers, C.; Raschke, M. B. Nano Lett. 2010, 10, 592–596. doi:10.1021/nl903574a
    Return to citation in text: [1] [2]
  13. Verhagen, E.; Spasenović, M.; Polman, A.; Kuipers, L. Phys. Rev. Lett. 2009, 102, 203904. doi:10.1103/PhysRevLett.102.203904
    Return to citation in text: [1] [2]
  14. Stratton, J. A. Electromagnetic Theory; McGraw-Hill: New York and London, 1941.
    Return to citation in text: [1] [2]
  15. Ashley, J.; Emerson, L. Surf. Sci. 1974, 41, 615–618. doi:10.1016/0039-6028(74)90080-6
    Return to citation in text: [1] [2]
  16. Pfeiffer, C. A.; Economou, E. N.; Ngai, K. L. Phys. Rev. B 1974, 10, 3038–3051. doi:10.1103/PhysRevB.10.3038
    Return to citation in text: [1] [2]
  17. Johnson, P. B.; Christy, R. W. Phys. Rev. B 1972, 6, 4370–4379. doi:10.1103/PhysRevB.6.4370
    Return to citation in text: [1]
  18. Koglin, J.; Fischer, U. C.; Fuchs, H. Phys. Rev. B 1997, 55, 7977–7984. doi:10.1103/PhysRevB.55.7977
    Return to citation in text: [1]
  19. Esteban, R.; Vogelgesang, R.; Kern, K. Nanotechnology 2006, 17, 475–482. doi:10.1088/0957-4484/17/2/022
    Return to citation in text: [1]
  20. Novotny, L.; Hecht, B. Principles of Nano-Optics; Cambridge University Press: Cambridge, 2006. doi:10.1017/CBO9780511813535
    Return to citation in text: [1]
  21. Knoll, B.; Keilmann, F. Opt. Commun. 2000, 182, 321–328. doi:10.1016/S0030-4018(00)00826-9
    Return to citation in text: [1] [2]
  22. Raschke, M. B.; Lienau, C. Appl. Phys. Lett. 2003, 83, 5089–5091. doi:10.1063/1.1632023
    Return to citation in text: [1] [2]
  23. Simon, H. J.; Guha, J. K. Opt. Commun. 1976, 18, 391–394. doi:10.1016/0030-4018(76)90158-9
    Return to citation in text: [1]
  24. Hecht, B.; Bielefeldt, H.; Novotny, L.; Inouye, Y.; Pohl, D. W. Phys. Rev. Lett. 1996, 77, 1889–1892. doi:10.1103/PhysRevLett.77.1889
    Return to citation in text: [1] [2]
  25. Drezet, A.; Hohenau, A.; Stepanov, A. L.; Ditlbacher, H.; Steinberger, B.; Galler, N.; Aussenegg, F. R.; Leitner, A.; Krenn, J. R. Appl. Phys. Lett. 2006, 89, 091117. doi:10.1063/1.2339043
    Return to citation in text: [1]
  26. Esteban, R.; Vogelgesang, R.; Kern, K. Phys. Rev. B 2007, 75, 195410. doi:10.1103/PhysRevB.75.195410
    Return to citation in text: [1]
  27. Behr, N.; Raschke, M. B. J. Phys. Chem. C 2008, 112, 3766–3773. doi:10.1021/jp7098009
    Return to citation in text: [1]
  28. Park, D. J.; Piglosiewicz, B.; Schmidt, S.; Kollmann, H.; Mascheck, M.; Groß, P.; Lienau, C. Ann. Phys. (Berlin, Ger.) 2013, 525, 135–142. doi:10.1002/andp.201200216
    Return to citation in text: [1]
  29. Lee, J. S.; Han, S.; Shirdel, J.; Koo, S.; Sadiq, D.; Lienau, C.; Park, N. Opt. Express 2011, 19, 12342–12347. doi:10.1364/OE.19.012342
    Return to citation in text: [1]
Top
Figure 1: Scanning electron micrographs of two gold tapers that were obtained by electrochemical AC-etching of annealed gold wires followed by focused ion beam milling of the grating couplers. Field enhancement at the taper apex was much more pronounced for the tip shown in panel a). Move  Close
Figure 2: Propagation constants kz of the three lowest eigenmodes of an infinitely long gold wire as a function of wire radius R. Displayed are the real (solid blue lines) and imaginary (dotted red lines) parts of kz pointing along the taper axis for angular momenta n = 0,1,2 (panels a)–c)). The SPP frequency corresponds to a vacuum wavelength of 800 nm, as used in the experiment. For n = 0, both Re(kz) and Im(kz) diverge for small radii. For n = 1, kz approaches the light line, k0 = ω/c0, for small radii. A cutoff behavior at approximately 600 nm is observed for n = 2. Panel d) summarizes these findings and schematically illustrates the mode profiles. Move  Close
Figure 3: Setup for k-space imaging of radiation emitted from the apex of a sharp gold taper. SPP wavepackets launched via a grating coupler are adiabatically nanofocused. A gold-coated cover slip is brought into close proximity of the taper. Light scattered through the cover slip is collected with a high numerical aperture objective (NA = 1.3). The spatial Fourier transform of light in the front focal plane is imaged from the back focal plane of the objective onto a CCD camera. A spatial filter is applied in the intermediate real image plane. Move  Close
Figure 4: k-space patterns recorded while approaching a gold-coated cover slip to the SNOM probe. Tip-sample spacings are indicated in the lower right corner of the respective images and the corresponding pictographs in the lower left corner. Panel a) shows raw data, the dashed circles mark the region of interest (ROI, labeled iv). Panels b)-g) represent the evolution of the k-space pattern during approach. For clarity, the data are limited to the ROI and are rescaled to the 90th percentile of all pixel intensities within the ROI in panel g). Move  Close
Figure 5: Quantitative analysis of the evolution of k-space patterns during tip approach and retraction. Panel a) shows the angular intensity distribution, radially integrated across the ROI (cf. Figure 4a), as a function of tip–sample spacing. At each angle, the data have been normalized. The region between the two dashed white lines has been averaged with respect to the angle and the data have been plotted in panel b) together with an exponential fit to the part of the data recorded during approach. The decay length is 14 nm. Here, the data have been normalized to the background signal. The inset shows an equal set of data for a different angular region around 110°. Move  Close
13.Verhagen, E.; Spasenović, M.; Polman, A.; Kuipers, L. Phys. Rev. Lett. 2009, 102, 203904. doi:10.1103/PhysRevLett.102.203904
14.Stratton, J. A. Electromagnetic Theory; McGraw-Hill: New York and London, 1941.
15.Ashley, J.; Emerson, L. Surf. Sci. 1974, 41, 615–618. doi:10.1016/0039-6028(74)90080-6
16.Pfeiffer, C. A.; Economou, E. N.; Ngai, K. L. Phys. Rev. B 1974, 10, 3038–3051. doi:10.1103/PhysRevB.10.3038
Go to references 13-16
14.Stratton, J. A. Electromagnetic Theory; McGraw-Hill: New York and London, 1941.
15.Ashley, J.; Emerson, L. Surf. Sci. 1974, 41, 615–618. doi:10.1016/0039-6028(74)90080-6
16.Pfeiffer, C. A.; Economou, E. N.; Ngai, K. L. Phys. Rev. B 1974, 10, 3038–3051. doi:10.1103/PhysRevB.10.3038
Go to references 14-16
10.Sadiq, D.; Shirdel, J.; Lee, J. S.; Selishcheva, E.; Park, N.; Lienau, C. Nano Lett. 2011, 11, 1609–1613. doi:10.1021/nl1045457
Go to reference 10
10.Sadiq, D.; Shirdel, J.; Lee, J. S.; Selishcheva, E.; Park, N.; Lienau, C. Nano Lett. 2011, 11, 1609–1613. doi:10.1021/nl1045457
Go to reference 10
23.Simon, H. J.; Guha, J. K. Opt. Commun. 1976, 18, 391–394. doi:10.1016/0030-4018(76)90158-9
24.Hecht, B.; Bielefeldt, H.; Novotny, L.; Inouye, Y.; Pohl, D. W. Phys. Rev. Lett. 1996, 77, 1889–1892. doi:10.1103/PhysRevLett.77.1889
25.Drezet, A.; Hohenau, A.; Stepanov, A. L.; Ditlbacher, H.; Steinberger, B.; Galler, N.; Aussenegg, F. R.; Leitner, A.; Krenn, J. R. Appl. Phys. Lett. 2006, 89, 091117. doi:10.1063/1.2339043
Go to references 23-25
20.Novotny, L.; Hecht, B. Principles of Nano-Optics; Cambridge University Press: Cambridge, 2006. doi:10.1017/CBO9780511813535
Go to reference 20
21.Knoll, B.; Keilmann, F. Opt. Commun. 2000, 182, 321–328. doi:10.1016/S0030-4018(00)00826-9
22.Raschke, M. B.; Lienau, C. Appl. Phys. Lett. 2003, 83, 5089–5091. doi:10.1063/1.1632023
Go to references 21,22
11.Schmidt, S.; Piglosiewicz, B.; Sadiq, D.; Shirdel, J.; Lee, J. S.; Vasa, P.; Park, N.; Kim, D.-S.; Lienau, C. ACS Nano 2012, 6, 6040–6048. doi:10.1021/nn301121h
Go to reference 11
11.Schmidt, S.; Piglosiewicz, B.; Sadiq, D.; Shirdel, J.; Lee, J. S.; Vasa, P.; Park, N.; Kim, D.-S.; Lienau, C. ACS Nano 2012, 6, 6040–6048. doi:10.1021/nn301121h
Go to reference 11
17.Johnson, P. B.; Christy, R. W. Phys. Rev. B 1972, 6, 4370–4379. doi:10.1103/PhysRevB.6.4370
Go to reference 17
18.Koglin, J.; Fischer, U. C.; Fuchs, H. Phys. Rev. B 1997, 55, 7977–7984. doi:10.1103/PhysRevB.55.7977
19.Esteban, R.; Vogelgesang, R.; Kern, K. Nanotechnology 2006, 17, 475–482. doi:10.1088/0957-4484/17/2/022
Go to references 18,19
6.Stockman, M. I. Phys. Rev. Lett. 2004, 93, 137404. doi:10.1103/PhysRevLett.93.137404
Go to reference 6
9.Ropers, C.; Neacsu, C. C.; Elsaesser, T.; Albrecht, M.; Raschke, M. B.; Lienau, C. Nano Lett. 2007, 7, 2784–2788. doi:10.1021/nl071340m
Go to reference 9
5.Babadjanyan, A. J.; Margaryan, N. L.; Nerkararyan, K. V. J. Appl. Phys. 2000, 87, 3785–3788. doi:10.1063/1.372414
6.Stockman, M. I. Phys. Rev. Lett. 2004, 93, 137404. doi:10.1103/PhysRevLett.93.137404
Go to references 5,6
6.Stockman, M. I. Phys. Rev. Lett. 2004, 93, 137404. doi:10.1103/PhysRevLett.93.137404
Go to reference 6
8.Issa, N.; Guckenberger, R. Plasmonics 2007, 2, 31–37. doi:10.1007/s11468-006-9022-7
Go to reference 8
6.Stockman, M. I. Phys. Rev. Lett. 2004, 93, 137404. doi:10.1103/PhysRevLett.93.137404
Go to reference 6
2.Aubry, A.; Lei, D. Y.; Fernández-Dominguez, A. I.; Sonnefraud, Y.; Maier, S. A.; Pendry, J. B. Nano Lett. 2010, 10, 2574–2579. doi:10.1021/nl101235d
3.Gramotnev, D. K. J. Appl. Phys. 2005, 98, 104302. doi:10.1063/1.2130520
4.Luo, Y.; Pendry, J. B.; Aubry, A. Nano Lett. 2010, 10, 4186–4191. doi:10.1021/nl102498s
5.Babadjanyan, A. J.; Margaryan, N. L.; Nerkararyan, K. V. J. Appl. Phys. 2000, 87, 3785–3788. doi:10.1063/1.372414
Go to references 2-5
5.Babadjanyan, A. J.; Margaryan, N. L.; Nerkararyan, K. V. J. Appl. Phys. 2000, 87, 3785–3788. doi:10.1063/1.372414
6.Stockman, M. I. Phys. Rev. Lett. 2004, 93, 137404. doi:10.1103/PhysRevLett.93.137404
7.Durach, M.; Rusina, A.; Stockman, M. I.; Nelson, K. Nano Lett. 2007, 7, 3145–3149. doi:10.1021/nl071718g
Go to references 5-7
26.Esteban, R.; Vogelgesang, R.; Kern, K. Phys. Rev. B 2007, 75, 195410. doi:10.1103/PhysRevB.75.195410
27.Behr, N.; Raschke, M. B. J. Phys. Chem. C 2008, 112, 3766–3773. doi:10.1021/jp7098009
28.Park, D. J.; Piglosiewicz, B.; Schmidt, S.; Kollmann, H.; Mascheck, M.; Groß, P.; Lienau, C. Ann. Phys. (Berlin, Ger.) 2013, 525, 135–142. doi:10.1002/andp.201200216
Go to references 26-28
24.Hecht, B.; Bielefeldt, H.; Novotny, L.; Inouye, Y.; Pohl, D. W. Phys. Rev. Lett. 1996, 77, 1889–1892. doi:10.1103/PhysRevLett.77.1889
Go to reference 24
1.Gramotnev, D. K.; Bozhevolnyi, S. I. Nat. Photonics 2010, 4, 83–91. doi:10.1038/nphoton.2009.282
Go to reference 1
29.Lee, J. S.; Han, S.; Shirdel, J.; Koo, S.; Sadiq, D.; Lienau, C.; Park, N. Opt. Express 2011, 19, 12342–12347. doi:10.1364/OE.19.012342
Go to reference 29
11.Schmidt, S.; Piglosiewicz, B.; Sadiq, D.; Shirdel, J.; Lee, J. S.; Vasa, P.; Park, N.; Kim, D.-S.; Lienau, C. ACS Nano 2012, 6, 6040–6048. doi:10.1021/nn301121h
Go to reference 11
11.Schmidt, S.; Piglosiewicz, B.; Sadiq, D.; Shirdel, J.; Lee, J. S.; Vasa, P.; Park, N.; Kim, D.-S.; Lienau, C. ACS Nano 2012, 6, 6040–6048. doi:10.1021/nn301121h
Go to reference 11
9.Ropers, C.; Neacsu, C. C.; Elsaesser, T.; Albrecht, M.; Raschke, M. B.; Lienau, C. Nano Lett. 2007, 7, 2784–2788. doi:10.1021/nl071340m
10.Sadiq, D.; Shirdel, J.; Lee, J. S.; Selishcheva, E.; Park, N.; Lienau, C. Nano Lett. 2011, 11, 1609–1613. doi:10.1021/nl1045457
11.Schmidt, S.; Piglosiewicz, B.; Sadiq, D.; Shirdel, J.; Lee, J. S.; Vasa, P.; Park, N.; Kim, D.-S.; Lienau, C. ACS Nano 2012, 6, 6040–6048. doi:10.1021/nn301121h
12.Neacsu, C. C.; Berweger, S.; Olmon, R. L.; Saraf, L. V.; Ropers, C.; Raschke, M. B. Nano Lett. 2010, 10, 592–596. doi:10.1021/nl903574a
Go to references 9-12
13.Verhagen, E.; Spasenović, M.; Polman, A.; Kuipers, L. Phys. Rev. Lett. 2009, 102, 203904. doi:10.1103/PhysRevLett.102.203904
Go to reference 13
10.Sadiq, D.; Shirdel, J.; Lee, J. S.; Selishcheva, E.; Park, N.; Lienau, C. Nano Lett. 2011, 11, 1609–1613. doi:10.1021/nl1045457
11.Schmidt, S.; Piglosiewicz, B.; Sadiq, D.; Shirdel, J.; Lee, J. S.; Vasa, P.; Park, N.; Kim, D.-S.; Lienau, C. ACS Nano 2012, 6, 6040–6048. doi:10.1021/nn301121h
Go to references 10,11
12.Neacsu, C. C.; Berweger, S.; Olmon, R. L.; Saraf, L. V.; Ropers, C.; Raschke, M. B. Nano Lett. 2010, 10, 592–596. doi:10.1021/nl903574a
Go to reference 12
11.Schmidt, S.; Piglosiewicz, B.; Sadiq, D.; Shirdel, J.; Lee, J. S.; Vasa, P.; Park, N.; Kim, D.-S.; Lienau, C. ACS Nano 2012, 6, 6040–6048. doi:10.1021/nn301121h
Go to reference 11
21.Knoll, B.; Keilmann, F. Opt. Commun. 2000, 182, 321–328. doi:10.1016/S0030-4018(00)00826-9
22.Raschke, M. B.; Lienau, C. Appl. Phys. Lett. 2003, 83, 5089–5091. doi:10.1063/1.1632023
Go to references 21,22
© 2013 Esmann et al; licensee Beilstein-Institut.
This is an Open Access article under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/2.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
The license is subject to the Beilstein Journal of Nanotechnology terms and conditions: (http://www.beilstein-journals.org/bjnano)