Determination of elastic moduli of elastic–plastic microspherical materials using nanoindentation simulation without mechanical polishing

• Hongzhou Li and
• Jialian Chen

Beilstein J. Nanotechnol. 2021, 12, 213–221, doi:10.3762/bjnano.12.17

• cannot be controlled. There are no reliable theoretical or experimental methods to evaluate the mechanical behavior during nanoindentation of an elastic–plastic microsphere. Therefore, it is necessary to conduct reliable numerical simulations to evaluate this behavior. This article reports a systematic

• computational study regarding the instrumented nanoindentation of elastic–plastic microspherical materials. The ratio between elastic modulus of the microsphere and the initial yield stress of the microsphere was systematically varied from 10 to 1000 to cover the mechanical properties of most materials

• depends on the indentation depth. It demonstrates that nanoindentation on microspherical materials exhibits a “size effect”. Keywords: elastic–plastic; microsphere; nanoindentation; Oliver–Pharr method; simulation; Introduction Instrumented nanoindentation is the most commonly used technique for the

Nanotribological behavior of deep cryogenically treated martensitic stainless steel

• Germán Prieto,
• Konstantinos D. Bakoglidis,
• Walter R. Tuckart and
• Esteban Broitman

Beilstein J. Nanotechnol. 2017, 8, 1760–1768, doi:10.3762/bjnano.8.177

• nitrogen for 2 h and annealed. The elastic–plastic parameters of the materials were assessed by nanoindentation tests under displacement control, while the friction behavior and wear rate were evaluated by a nanoscratch testing methodology that it is used for the first time in steels. It was found that

• software INFOSTAT [28]. When carrying out nanoindentations in an elastic–plastic material like a metal, it tends to accumulate around the indenter, forming a pile-up that is higher than the sample surface. This phenomenon can lead to the underestimation of the true contact area and a significant deviation

Possibilities and limitations of advanced transmission electron microscopy for carbon-based nanomaterials

• Xiaoxing Ke,
• Carla Bittencourt and
• Gustaaf Van Tendeloo

Beilstein J. Nanotechnol. 2015, 6, 1541–1557, doi:10.3762/bjnano.6.158

• instance, the evolution of defects (such as the shear strain present in CNTs as discussed in Section 3.1) along with the elastic/plastic deformation in CNT-reinforced composites under load can be well studied using similar techniques [109]. In contrast to the external stimuli, which are introduced through

Trade-offs in sensitivity and sampling depth in bimodal atomic force microscopy and comparison to the trimodal case

• Babak Eslami,
• Daniel Ebeling and
• Santiago D. Solares

Beilstein J. Nanotechnol. 2014, 5, 1144–1151, doi:10.3762/bjnano.5.125

• implementation of Rodriguez and Garcia was for imaging in the attractive regime [12][13]. In the repulsive imaging regime the cantilever tip intermittently impacts the sample and thus the images are governed by contact forces that are a consequence of elastic, plastic, viscous or adhesive surface behaviors, in

A nanometric cushion for enhancing scratch and wear resistance of hard films

• Katya Gotlib-Vainshtein,
• Olga Girshevitz,
• Chaim N. Sukenik,
• David Barlam and
• Sidney R. Cohen

Beilstein J. Nanotechnol. 2014, 5, 1005–1015, doi:10.3762/bjnano.5.114

• polymers. One is to decrease E/σy, where E is Young's modulus and σy the yield stress. Materials with a low E/σy ratio are less easily scratched [6]. Another way is to increase the elastic relaxation in elastic–plastic strain by increasing the strain-hardening coefficient [6][7][8]. Polymeric composites

Scale effects of nanomechanical properties and deformation behavior of Au nanoparticle and thin film using depth sensing nanoindentation

• Dave Maharaj and
• Bharat Bhushan

Beilstein J. Nanotechnol. 2014, 5, 822–836, doi:10.3762/bjnano.5.94

• understanding of materials behavior during contact. Mechanical properties of interest comprise hardness, Young’s modulus of elasticity, bulk modulus, elastic–plastic deformation, scratch resistance, residual stresses, time-dependent creep and relaxation properties, fracture toughness, fatigue and yield strength

Effect of normal load and roughness on the nanoscale friction coefficient in the elastic and plastic contact regime

• Aditya Kumar,
• Thorsten Staedler and
• Xin Jiang

Beilstein J. Nanotechnol. 2013, 4, 66–71, doi:10.3762/bjnano.4.7

• account for elastic–plastic asperity contacts, Chang (CEB model [7][8]) extended the GW model to an elastic–plastic regime assuming the volume conservation law for asperities. However, the CEB model neglects the higher plasticity of the contact in resistance to the additional tangential loading. Later