A visible-light-controlled platform for prolonged drug release based on Ag-doped TiO₂ nanotubes with a hydrophobic layer

• Caihong Liang,
• Jiang Wen and
• Xiaoming Liao

Beilstein J. Nanotechnol. 2018, 9, 1793–1801, doi:10.3762/bjnano.9.170

• the oxygen atoms of ZnO. Figure 5 demonstrates the water contact angles (CAs) of the different treated samples. As-grown TiO2 nanotube arrays presents total hydrophilicity with a water CA of 30° (Figure 5a) without any surficial alteration [2][3]. Besides, TNTs modified with Ag (Figure 5b) and ZnO-Ag

• (Figure 5c) show hydrophilicity as well. Meanwhile, the CAs of modified TNTs increased slightly by 19° after decoration with Ag and then decreased by 16° due to the loading of the Zn2+-based drug. Furthermore, organic mutilayers with functional groups, including carboxylates or silanes [32], can be used

Preparation and morphology-dependent wettability of porous alumina membranes

• Dmitry L. Shimanovich,
• Alla I. Vorobjova,
• Daria I. Tishkevich,
• Alex V. Trukhanov,
• Maxim V. Zdorovets and
• Artem L. Kozlovskiy

Beilstein J. Nanotechnol. 2018, 9, 1423–1436, doi:10.3762/bjnano.9.135

• two surfaces: the front (or outer) and back (or inner) surfaces. Preliminary studies have shown that these surfaces possess different physicochemical properties due to different degrees of hydrophilicity (as well as wettability). This concerns both industrially manufactured commercial membranes (e.g

• ., PAM, nanochannel alumina NCA templates, Anodisc TM 25, Whatman Plc.) and domestically fabricated (in-house manufactured) PAMs. The degree of PAM hydrophilicity was determined by measuring the interfacial contact angle (ICA), θ, by the recumbent drop method [33]. To do this, a drop of distilled water

Atomic-level characterization and cilostazol affinity of poly(lactic acid) nanoparticles conjugated with differentially charged hydrophilic molecules

• María Francisca Matus,
• Martín Ludueña,
• Cristian Vilos,
• Iván Palomo and
• Marcelo M. Mariscal

Beilstein J. Nanotechnol. 2018, 9, 1328–1338, doi:10.3762/bjnano.9.126

• in the medical field [13], the applications of PLA are limited, mainly due to its weak hydrophilicity and low drug loading of polar drugs [14]. However, PLA nanoparticles conjugated with hydrophilic molecules like poly(ethylene glycol) (PEG) are a singular kind of functionalized NPs. Several studies

• hydrophilicity/hydrophobicity ratio, the size and surface chemistry are crucial factors in NP–cell interactions. Several studies on metallic NPs, carbon nanotubes, and dendrimers have shown that toxicity of different NPs is determined by a combination of these factors [25][26][27][28][29]. In this respect

Scanning speed phenomenon in contact-resonance atomic force microscopy

• Christopher C. Glover,
• Jason P. Killgore and
• Ryan C. Tung

Beilstein J. Nanotechnol. 2018, 9, 945–952, doi:10.3762/bjnano.9.87

• hydrophilic and hydrophobic surfaces matches results reported by Bhushan and co-workers [38]. The scan speed phenomenon was not observed on HOPG at 36% or 70% RH. Goertz et al. [37] found that the viscous interfacial water film did not exist when the hydrophilicity of their oxide-terminated silicon surface

A review of carbon-based and non-carbon-based catalyst supports for the selective catalytic reduction of nitric oxide

• Shahreen Binti Izwan Anthonysamy,
• Syahidah Binti Afandi,
• Mehrnoush Khavarian and
• Abdul Rahman Bin Mohamed

Beilstein J. Nanotechnol. 2018, 9, 740–761, doi:10.3762/bjnano.9.68

• will eventually agitate the uniform distribution of the active component onto the carbon support, the surface chemistry of the carbon material could be simply adjusted, for instance, by undergoing an oxidation process, in order to increase the hydrophilicity of the carbon materials. Aside from the easy

Enhancement of mechanical and electrical properties of continuous-fiber-reinforced epoxy composites with stacked graphene

• Naum Naveh,
• Olga Shepelev and
• Samuel Kenig

Beilstein J. Nanotechnol. 2017, 8, 1909–1918, doi:10.3762/bjnano.8.191

• spite of the very low viscosity of GLYMO. The hydrophilic/hydrophobic nature of the SAA dictates the surface energy balance, such that more hydrophilicity (thus, higher surface energies) drives the treated nanoparticles to the fiber/matrix interface, due to the higher surface energy of the Kevlar fibers

Surface functionalization of 3D-printed plastics via initiated chemical vapor deposition

• Christine Cheng and
• Malancha Gupta

Beilstein J. Nanotechnol. 2017, 8, 1629–1636, doi:10.3762/bjnano.8.162

• hydrophobicity caused its pores to also remain filled with air. Unlike the hydrophobic lattices, the lattice coated with P(HEMA-co-EGDA) wicked water into its pores because of the hydrophilicity and the lattice sank in the water. To demonstrate the efficacy of the incorporated cross-linker for preventing

• dissolution of the polymer coating, the lattice coated with P(HEMA-co-EGDA) was soaked in water for three days and then was dried and placed back into the water, whereupon it sank, demonstrating the retention of its hydrophilicity. To study the limitations of the iCVD process for coating macro-scale plastics

Oxidative stabilization of polyacrylonitrile nanofibers and carbon nanofibers containing graphene oxide (GO): a spectroscopic and electrochemical study

• İlknur Gergin,
• Ezgi Ismar and
• A. Sezai Sarac

Beilstein J. Nanotechnol. 2017, 8, 1616–1628, doi:10.3762/bjnano.8.161

• hydrophilicity of the PAN precursor but also catalyze the cyclization of nitrile groups during the stabilization process by forming a ladder structure. In our previous studies, copolymers of AN have been synthesized by free radical polymerization, and electrospun nanofibers were obtained with different AN co

Preparation of thick silica coatings on carbon fibers with fine-structured silica nanotubes induced by a self-assembly process

• Benjamin Baumgärtner,
• Hendrik Möller,
• Thomas Neumann and
• Dirk Volkmer

Beilstein J. Nanotechnol. 2017, 8, 1145–1155, doi:10.3762/bjnano.8.116

• the polyamine. Several other modifications of carbon fiber surfaces were examined confirming that an increase in hydrophilicity is beneficial for the LPEI self-assembly process. For example, a dense coating can be realized for anodic oxidized fibers, sulfonated fibers (obtained by treatment with

Fully scalable one-pot method for the production of phosphonic graphene derivatives

• Kamila Żelechowska,
• Marta Prześniak-Welenc,
• Marcin Łapiński,
• Izabela Kondratowicz and
• Tadeusz Miruszewski

Beilstein J. Nanotechnol. 2017, 8, 1094–1103, doi:10.3762/bjnano.8.111

• water molecules due to high hydrophilicity of the GO. The well-developed band at 1730 cm−1 confirms the presence of carboxylic groups in the GO. Stretching vibrations of double carbon–carbon bonds in the GO structure gave the expected band at 1625 cm−1. The position of the band indicates that such bonds

α-((4-Cyanobenzoyl)oxy)-ω-methyl poly(ethylene glycol): a new stabilizer for silver nanoparticles

• Jana Lutze,
• Miguel A. Bañares,
• Marcos Pita,
• Andrea Haase,
• Andreas Luch and
• Andreas Taubert

Beilstein J. Nanotechnol. 2017, 8, 627–635, doi:10.3762/bjnano.8.67

• hydrophilicity and biological inertness of PEG, which renders PEG-stabilized NPs water-soluble and less susceptible to opsonization [19][20]. As a result, PEG-coated NPs are often referred to as “stealth” NPs [21][22]. Moreover, PEG coatings often lower the toxicity of otherwise toxic NPs [23][24]. For example

Surface roughness rather than surface chemistry essentially affects insect adhesion

• Matt W. England,
• Tomoya Sato,
• Makoto Yagihashi,
• Atsushi Hozumi,
• Stanislav N. Gorb and
• Elena V. Gorb

Beilstein J. Nanotechnol. 2016, 7, 1471–1479, doi:10.3762/bjnano.7.139

• agreement with its marked increase in hydrophilicity (superhydrophilicity). Interestingly, the XPS analysis also revealed that the Never Wet surface had the lowest concentration of C (ca. 24 atom %) of any non-perfluorinated sample surface and showed excellent static/dynamic dewetting behavior. In addition

Three-gradient regular solution model for simple liquids wetting complex surface topologies

• Sabine Akerboom,
• Marleen Kamperman and
• Frans A. M. Leermakers

Beilstein J. Nanotechnol. 2016, 7, 1377–1396, doi:10.3762/bjnano.7.129

Multiwalled carbon nanotube hybrids as MRI contrast agents

• Nikodem Kuźnik and
• Mateusz M. Tomczyk

Beilstein J. Nanotechnol. 2016, 7, 1086–1103, doi:10.3762/bjnano.7.102

• hydrophilicity resulting in a more effective water exchange (τM in Equation 3) and the higher number of water molecules in the vicinity. Some structural factors may serve to additionally enhance the relaxivities. In the CNT net, shorter Gd–O bonds were found and this also translates into a stronger Gd–OH2

Magnetic switching of nanoscale antidot lattices

• Ulf Wiedwald,
• Joachim Gräfe,
• Kristof M. Lebecki,
• Maxim Skripnik,
• Felix Haering,
• Gisela Schütz,
• Paul Ziemann,
• Eberhard Goering and
• Ulrich Nowak

Beilstein J. Nanotechnol. 2016, 7, 733–750, doi:10.3762/bjnano.7.65

Correlative infrared nanospectroscopic and nanomechanical imaging of block copolymer microdomains

• Benjamin Pollard and
• Markus B. Raschke

Beilstein J. Nanotechnol. 2016, 7, 605–612, doi:10.3762/bjnano.7.53

• or capillary forces). It can reflect variations in the Hamaker constant of the van der Waals interaction, surface charges, or hydrophilicity [32]. It has been observed in PS-b-PMMA that PS preferentially adsorbs onto a gold surface compared to PMMA [33]. Thus, the higher attractive forces over PS

Chemical bath deposition of textured and compact zinc oxide thin films on vinyl-terminated polystyrene brushes

• Nina J. Blumenstein,
• Caroline G. Hofmeister,
• Peter Lindemann,
• Cheng Huang,
• Johannes Baier,
• Andreas Leineweber,
• Stefan Walheim,
• Christof Wöll,
• Thomas Schimmel and
• Joachim Bill

Beilstein J. Nanotechnol. 2016, 7, 102–110, doi:10.3762/bjnano.7.12

• [38]. This could lead to a smaller difference in the ζ-potential of the SiOx and PS brush in methanol as compared to the results in water. Water contact angle (WCA) measurements confirm the findings of the ζ-potential measurements. The SiOx surface exhibits a high hydrophilicity with a WCA below 4

Chemiresistive/SERS dual sensor based on densely packed gold nanoparticles

• Sanda Boca,
• Cosmin Leordean,
• Simion Astilean and
• Cosmin Farcau

Beilstein J. Nanotechnol. 2015, 6, 2498–2503, doi:10.3762/bjnano.6.259

• to increase the hydrophilicity of the IDE surface. The convective self-assembly (CSA) deposition setup consists in a glass deposition plate placed at an angle of 30° over the horizontal IDE fixed substrate. A drop (5 µL) of gold nanoparticles was placed in the wedge between the plate and IDE. Strip

Nanostructured surfaces by supramolecular self-assembly of linear oligosilsesquioxanes with biocompatible side groups

• Maria Nowacka,
• Anna Kowalewska and
• Tomasz Makowski

Beilstein J. Nanotechnol. 2015, 6, 2377–2387, doi:10.3762/bjnano.6.244

• structure of the applied oligomers and primers. Keywords: atomic force microscopy; hydrophilicity; oligosilsesquioxanes; self-assembly; surface; Introduction The modification of surface properties can be used as a versatile tool in materials engineering for biological and medical purposes [1][2][3][4

• LPSQ-COOH/X and the chemical specificity of the support. The functional groups in side chains have a significant impact on the arrangement of macromolecules, surface pattern and hydrophilicity. The distribution of the studied macromolecules within the adsorbed PSAMs is a consequence of both polymer

Plasma fluorination of vertically aligned carbon nanotubes: functionalization and thermal stability

• Claudia Struzzi,
• Mattia Scardamaglia,
• Axel Hemberg,
• Luca Petaccia,
• Jean-François Colomer,
• Rony Snyders and
• Carla Bittencourt

Beilstein J. Nanotechnol. 2015, 6, 2263–2271, doi:10.3762/bjnano.6.232

• the desorption of physically adsorbed oxygen associated with the formation of hydroxyperoxide after air exposure of freshly functionalized nanotubes [14]. A recent study reported on the improved hydrophilicity of carbon nanostructures upon oxyfluorination [40]. Indeed the presence of hydroxylic groups

Fabrication of hybrid nanocomposite scaffolds by incorporating ligand-free hydroxyapatite nanoparticles into biodegradable polymer scaffolds and release studies

• Balazs Farkas,
• Marina Rodio,
• Ilaria Romano,
• Alberto Diaspro,
• Romuald Intartaglia and
• Szabolcs Beke

Beilstein J. Nanotechnol. 2015, 6, 2217–2223, doi:10.3762/bjnano.6.227

• of HA enhanced hydrophilicity and serum protein adsorption, and as a result, this increased pre-osteoblast cell attachment, spreading, and proliferation after four days of culture. Different technical routes have been explored for the synthesis of HA NPs, including mechanochemical synthesis [10

Nanofibers for drug delivery – incorporation and release of model molecules, influence of molecular weight and polymer structure

• Jakub Hrib,
• Jakub Sirc,
• Radka Hobzova,
• Zuzana Hampejsova,
• Zuzana Bosakova,
• Marcela Munzarova and
• Jiri Michalek

Beilstein J. Nanotechnol. 2015, 6, 1939–1945, doi:10.3762/bjnano.6.198

• observed and may have been suppressed by other factors, i.e., the degree of hydrophilicity of nanofibers. The obtained results showed the successful preparation of morphologically comparable nanofibrous materials with incorporated PEG molecules. It was demonstrated that combination of chemically different

Self-assembled anchor layers/polysaccharide coatings on titanium surfaces: a study of functionalization and stability

• Ognen Pop-Georgievski,
• Dana Kubies,
• Josef Zemek,
• Neda Neykova,
• Roman Demianchuk,
• Eliška Mázl Chánová,
• Miroslav Šlouf,
• Milan Houska and
• František Rypáček

Beilstein J. Nanotechnol. 2015, 6, 617–631, doi:10.3762/bjnano.6.63

• established continuity of the layers are examined by scanning electron microscopy, surface profilometry and atomic force microscopy. The changes in hydrophilicity after each modification step are further examined by contact angle goniometry. Keywords: alginate; biomimetic surfaces; bisphosphonates

• changes in hydrophilicity after each modification and immersion step are further examined by contact angle goniometry. Results and Discussion Surface analysis of activated titanium surfaces The surface concentration of elements present on pristine, activated and flat titanium surfaces, as determined by

• evidenced by the higher hydrophilicity of the treated surfaces (Supporting Information File 1, Table S2). The activation treatments decrease the measured advancing water contact angles from about 50° for the pristine titanium surfaces to values lower than 30°. Almost completely wettable surfaces were

Conformal SiO₂ coating of sub-100 nm diameter channels of polycarbonate etched ion-track channels by atomic layer deposition

• Nicolas Sobel,
• Christian Hess,
• Manuela Lukas,
• Anne Spende,
• Bernd Stühn,
• M. E. Toimil-Molares and
• Christina Trautmann

Beilstein J. Nanotechnol. 2015, 6, 472–479, doi:10.3762/bjnano.6.48

• narrow size distribution [4][5][6]. Typically, polymers such as polycarbonate (PC), polyethylene terephthalate, and polyimide are employed as templates. Hydrophilicity is sometimes improved by immersing the etched membrane in a surfactant solution such as polyvinylpyrrolidone. The addition of surfactants

• adjust specific surface properties such as hydrophilicity or catalytic activity. Conform ALD coatings have been reported for various porous materials including powders [18] and porous membranes such as anodic aluminum oxide (AAO) [19][20][21][22][23][24] and track-etched membranes [25][26][27][28]. For

• photoelectron spectroscopy (XPS) and Fourier-transform infrared spectroscopy (FTIR). The hydrophilicity of SiO2-coated PC membranes was tested by contact angle measurements. Experimental Figure 1 displays schematically the three main steps involved in the fabrication of SiO2 coated track-etched membranes. These

In situ scanning tunneling microscopy study of Ca-modified rutile TiO₂(110) in bulk water

• Giulia Serrano,
• Beatrice Bonanni,
• Tomasz Kosmala,
• Marco Di Giovannantonio,
• Ulrike Diebold,
• Klaus Wandelt and
• Claudio Goletti

Beilstein J. Nanotechnol. 2015, 6, 438–443, doi:10.3762/bjnano.6.44

• understanding of the system, leading to the optimization of many related applications. As an example, it was recently demonstrated that a low surface calcium coverage may increase the wetting energy and therefore the surface hydrophilicity of TiO2 surfaces [17]. This has very interesting implications for the