Controlling the proximity effect in a Co/Nb multilayer: the properties of electronic transport

• Sergey Bakurskiy,
• Mikhail Kupriyanov,
• Nikolay V. Klenov,
• Igor Soloviev,
• Andrey Schegolev,
• Roman Morari,
• Yury Khaydukov and
• Anatoli S. Sidorenko

Beilstein J. Nanotechnol. 2020, 11, 1336–1345, doi:10.3762/bjnano.11.118

• prepared by using the magnetron sputtering system Leybold Heraeus Z-400 during a single deposition cycle without depressurization of the chamber. Only three targets were used for the structure preparation: niobium (99.95% purity) was used as a superconducting Cooper pair generator and interlayer separator

Effect of localized helium ion irradiation on the performance of synthetic monolayer MoS₂ field-effect transistors

• Jakub Jadwiszczak,
• Pierce Maguire,
• Conor P. Cullen,
• Georg S. Duesberg and
• Hongzhou Zhang

Beilstein J. Nanotechnol. 2020, 11, 1329–1335, doi:10.3762/bjnano.11.117

• achieved by selective ion sputtering in thin film transistors has also been observed in He+-irradiated InGaZnO devices [27]. This irradiation-induced carrier activation depends not only on the fluence of the ion beam, but also on the absolute number of defects that can be introduced. Therefore, the

• atomic vacancy yield per each delivered ion as a function of target penetration depth on the 35 nm-Au/5 nm-Ti/0.7 nm-MoS2/285 nm-SiO2 stack [41]. As evident from Figure 3d, the sulfur sputtering yield at the Ti–MoS2 interface is very close to that of unencapsulated MoS2 [15], indicating notable damage to

Structural and electronic properties of SnO₂ doped with non-metal elements

• Jianyuan Yu,
• Yingeng Wang,
• Yan Huang,
• Xiuwen Wang,
• Jing Guo,
• Jingkai Yang and
• Hongli Zhao

Beilstein J. Nanotechnol. 2020, 11, 1321–1328, doi:10.3762/bjnano.11.116

• . Nguyen successfully prepared p-type N-doped SnO2 films using magnetron sputtering [9]. The results show that the SnO2 films were n-type semiconductors, and the concentration of free carriers in the film increased as the temperature for sedimentation increased. Also, p-type semiconductors were

An atomic force microscope integrated with a helium ion microscope for correlative nanoscale characterization

• Santiago H. Andany,
• Gregor Hlawacek,
• Stefan Hummel,
• Charlène Brillard,
• Mustafa Kangül and
• Georg E. Fantner

Beilstein J. Nanotechnol. 2020, 11, 1272–1279, doi:10.3762/bjnano.11.111

• used, in situ, in between exposures to assess the shrinkage, stiffness change or sputtering of the resist. More applications such as conductive AFM, piezo-force microscopy or magnetic force microscopy are within reach of the presented technology and would make AFM–HIM appealing to the microelectronics

Ultrasensitive detection of cadmium ions using a microcantilever-based piezoresistive sensor for groundwater

• Dinesh Rotake,
• Anand Darji and
• Nitin Kale

Beilstein J. Nanotechnol. 2020, 11, 1242–1253, doi:10.3762/bjnano.11.108

• . [28], but it is not suitable for other high-temperature sputtering processes. Microcantilevers based on SiO2 have been manufactured by Tang et al. [29] to enhance the sensitivity of cantilever sensors. Many authors use optical setups for microcantilevers. However, an optical output has several

Hybridization vs decoupling: influence of an h-BN interlayer on the physical properties of a lander-type molecule on Ni(111)

• Maximilian Schaal,
• Takumi Aihara,
• Marco Gruenewald,
• Felix Otto,
• Jari Domke,
• Roman Forker,
• Hiroyuki Yoshida and
• Torsten Fritz

Beilstein J. Nanotechnol. 2020, 11, 1168–1177, doi:10.3762/bjnano.11.101

• Ar+ sputtering at room temperature and annealing at 800 °C. The h-BN layer was grown by thermal dehydrogenation of borazine molecules at a substrate temperature of 800 °C similar to [19]. We purchased borazine from Katchem Ltd. (Czech Republic) with a specified purity of >98%. The quality of the h-BN

Gram-scale synthesis of splat-shaped Ag–TiO₂ nanocomposites for enhanced antimicrobial properties

• Mohammad Jaber,
• Asim Mushtaq,
• Kebiao Zhang,
• Jindan Wu,
• Dandan Luo,
• Zihan Yi,
• M. Zubair Iqbal and
• Xiangdong Kong

Beilstein J. Nanotechnol. 2020, 11, 1119–1125, doi:10.3762/bjnano.11.96

• , magnetron sputtering, molecular precursor techniques and photo-deposition techniques have been applied to the preparation of nanocomposites [6][21][22]. However, these techniques are very sophisticated and not optimized for synthesis on a large scale. Herein, a simple hydrothermal process was employed to

Monolayers of MoS₂ on Ag(111) as decoupling layers for organic molecules: resolution of electronic and vibronic states of TCNQ

• Asieh Yousofnejad,
• Gaël Reecht,
• Nils Krane,
• Christian Lotze and
• Katharina J. Franke

Beilstein J. Nanotechnol. 2020, 11, 1062–1071, doi:10.3762/bjnano.11.91

• vibronic states of the gas-phase molecule. Results and Discussion We have grown monolayer islands of MoS2 on an atomically clean Ag(111) surface, which had been exposed to sputtering–annealing cycles under ultrahigh vacuum before. The growth procedure was adapted from that of MoS2 on Au(111) [34][35], with

Excitonic and electronic transitions in Me–Sb₂Se₃ structures

• Nicolae N. Syrbu,
• Victor V. Zalamai,
• Ivan G. Stamov and
• Stepan I. Beril

Beilstein J. Nanotechnol. 2020, 11, 1045–1053, doi:10.3762/bjnano.11.89

• (In–Sb2Se3) contacts, the structures were obtained by either thermal sputtering under vacuum or electrochemical deposition onto the cleaved faces of single crystals (Figure 3A). Current–voltage characteristics suggest that the contacts have an ohmic behavior. The impedance has a frequency dependence

• structures and the excitonic band symmetries in the Brillouin zone center for crystals with an orthorhombic symmetry (Pnma). The In–Sb2Se3 structures were generated either by thermal sputtering under vacuum or by electrochemical deposition. The photoconductivity spectra at different applied voltages were

Gas-sensing features of nanostructured tellurium thin films

• Dumitru Tsiulyanu

Beilstein J. Nanotechnol. 2020, 11, 1010–1018, doi:10.3762/bjnano.11.85

• , nanotubes or nanowires from the gas phase under vacuum or argon atmosphere. On the other hand, nanostructuring can be performed mechanically as indicated by the possibility of growth of nanocrystalline gas sensors via rf sputtering (13.6 MHz) of Te in an ultra-high-purity argon atmosphere [24]. The main

• grown using either the thermal vacuum evaporation of pure Te [17][18][19][20] or its sputtering under a pure argon atmosphere [24] onto glass, Al2O3 or sapphire substrates. It was shown that the film morphology as well as the gas sensitivity is controlled by several factors, such as the nature and

Band tail state related photoluminescence and photoresponse of ZnMgO solid solution nanostructured films

• Vadim Morari,
• Aida Pantazi,
• Nicolai Curmei,
• Vitalie Postolache,
• Emil V. Rusu,
• Marius Enachescu,
• Ion M. Tiginyanu and
• Veaceslav V. Ursaki

Beilstein J. Nanotechnol. 2020, 11, 899–910, doi:10.3762/bjnano.11.75

• radio-frequency plasma-assisted molecular beam epitaxy (RF-MBE) [2][7][10][11], DC [12][13] and RF [1][3][6] magnetron sputtering, pulsed laser deposition (PLD) [14][15], plasma-enhanced atomic layer deposition (PE-ALD) [16], chemical vapor deposition (CVD) [17], metal–organic chemical vapor deposition

• –0.78 for Zn1−xMgxO thin films grown by reactive DC magnetron co-sputtering [12]. It was shown that this investigation technique is highly sensitive for the detection of embedded structural inhomogeneities, and it was found that the phase segregation occurs in the range of x = 0.35–0.65 with coexistence

Epitaxial growth and superconducting properties of thin-film PdFe/VN and VN/PdFe bilayers on MgO(001) substrates

• Wael M. Mohammed,
• Igor V. Yanilkin,
• Amir I. Gumarov,
• Airat G. Kiiamov,
• Roman V. Yusupov and
• Lenar R. Tagirov

Beilstein J. Nanotechnol. 2020, 11, 807–813, doi:10.3762/bjnano.11.65

• ) and Fe (99.97% purity, ChemPur GmbH, Germany) were co-evaporated from the pre-calibrated high-temperature effusion cells to obtain the desired Pd1−xFex composition. Vanadium nitride layers were synthesized by using reactive DC magnetron sputtering (MS) in the UHV chamber with a base pressure of p ≤ 5

• −xFex were taken at each deposition step using low-energy electron diffraction (LEED) and X-ray photoelectron spectroscopy (XPS). Finally, all structures were capped with 10 nm layer of undoped Si by magnetron sputtering to prevent sample deterioration. Thus, a VN film and stacks of Pd0.96Fe0.04/VN and

• sputtering. The obtained 30 nm thick VN films exhibit a sharp superconducting transition with Tc = 7.7 K and ΔTc = 25 mK. The heteroepitaxial Pd0.96Fe0.04/VN and VN/Pd0.92Fe0.08 structures reveal a superconductor–ferromagnet proximity suppression of the transition temperature to Tc = 6.1 K. This is, however

A set of empirical equations describing the observed colours of metal–anodic aluminium oxide–Al nanostructures

• Cristina V. Manzano,
• Jakob J. Schwiedrzik,
• Gerhard Bürki,
• Laszlo Pethö,
• Johann Michler and
• Laetitia Philippe

Beilstein J. Nanotechnol. 2020, 11, 798–806, doi:10.3762/bjnano.11.64

• .11.64 Abstract Structural colours have received a lot of attention regarding the reproduction of the vivid colours found in nature. In this study, metal–anodic aluminium oxide (AAO)–Al nanostructures were deposited using a two-step anodization and sputtering process to produce self-ordered anodic

• circle. Conclusion 8 nm Cr–AAO–Al and 10/17.5/25 nm Au–AAO–Al nanostructures were fabricated by combining sputtering deposition and a two-step anodization process. The AAO films with different thicknesses (from 209 ± 12 nm to 380 ± 15 nm) were anodized and the CIE Yxy values were obtained via reflectance

• Alliance-Concept DP 650 DC magnetron sputtering equipment. 25, 17.5 and 10 nm thin films of gold were deposited on top of the AAO films using a Leica EM ACE600 sputtering equipment. The Au layers were deposited using a sputtering pressure and intensity of 5 × 10−2 mbar and 30 mA, respectively, and the Cr

Effect of Ag loading position on the photocatalytic performance of TiO₂ nanocolumn arrays

• Jinghan Xu,
• Yanqi Liu and
• Yan Zhao

Beilstein J. Nanotechnol. 2020, 11, 717–728, doi:10.3762/bjnano.11.59

• photolithography and the template method by Sung et al. [30]. In this case, Ag particles were loaded on the outside of the nanocolumns by magnetron sputtering, and the catalysis was carried out at a sputtering time of 30 min. Besides, Jani et al. [31] studied the preparation of TiO2 nanotube arrays by anodization

Structural optical and electrical properties of a transparent conductive ITO/Al–Ag/ITO multilayer contact

• Aliyu Kabiru Isiyaku,
• Ahmad Hadi Ali and
• Nafarizal Nayan

Beilstein J. Nanotechnol. 2020, 11, 695–702, doi:10.3762/bjnano.11.57

• pure ITO layer (as reference) were prepared by RF and DC sputtering. The microstructural, optical and electrical properties of the ITO/Al–Ag/ITO (IAAI) films were investigated before and after annealing at 400 °C. X-ray diffraction measurements show that the insertion of the Al–Ag intermediate bilayer

• × 10−3 Ω−1). These highly conductive and transparent ITO films with Al–Ag interlayer can be a promising contact for low-resistance optoelectronics devices. Keywords: annealing; DC sputtering; figure of merit; indium tin oxide (ITO); multilayer structure; RF sputtering; Introduction Transparent

• overcome by adding a thin layer of Al, Au, Pd, or Cr to the Ag film to improve the adhesion [4][25][26]. Optical and electrical properties of ITO films are enhanced by post-deposition annealing especially at high temperatures [7]. Gulen et al. [27] exposed pure ITO films deposited by sputtering to heat

Evolution of Ag nanostructures created from thin films: UV–vis absorption and its theoretical predictions

• Robert Kozioł,
• Marcin Łapiński,
• Paweł Syty,
• Damian Koszelow,
• Wojciech Sadowski,
• Józef E. Sienkiewicz and
• Barbara Kościelska

Beilstein J. Nanotechnol. 2020, 11, 494–507, doi:10.3762/bjnano.11.40

• thickness) were deposited using a table-top dc magnetron sputtering coater (EM SCD 500, Leica) in pure Ar plasma (argon, Air Products 99.999%). The Ag target was of 99.99% purity, the rate of layer deposition was about 0.4 nm·s−1, and the incident power was in the range of 30–40 W. The layer thickness was

Atomic-resolution imaging of rutile TiO₂(110)-(1 × 2) reconstructed surface by non-contact atomic force microscopy

• Daiki Katsube,
• Shoki Ojima,
• Eiichi Inami and
• Masayuki Abe

Beilstein J. Nanotechnol. 2020, 11, 443–449, doi:10.3762/bjnano.11.35

• .) were used. A rutile TiO2(110)-(1 × 2) reconstructed surface was prepared by iterating a surface cleaning process of Ar+ sputtering (2 keV, Ar partial pressure of 3.0 × 10−4 Pa, ion current of ca. 1.1 µA, 10 min) and annealing (substrate temperature of ca. 1000 °C, 30 min). STM and NC-AFM imaging was

• performed using Pt-coated Si cantilevers (Budget Sensors, ElectriTAP190G). All cantilevers were cleaned by Ar+ sputtering (0.6 keV, Ar partial pressure of 1.0 × 10−5 Pa, ion current of 0.05 µA, 5 min) before scanning. STM imaging was performed in constant-current mode without cantilever oscillation. NC-AFM

Formation of nanoripples on ZnO flat substrates and nanorods by gas cluster ion bombardment

• Xiaomei Zeng,
• Vasiliy Pelenovich,
• Bin Xing,
• Rakhim Rakhimov,
• Wenbin Zuo,
• Alexander Tolstogouzov,
• Chuansheng Liu,
• Dejun Fu and
• Xiangheng Xiao

Beilstein J. Nanotechnol. 2020, 11, 383–390, doi:10.3762/bjnano.11.29

• was discovered by Navez et al. [7] and studied in details by Carter and co-workers [8]. Later, a theoretical explanation of the ripple formation was given by Bradley and Harper (BH) and Bradley and Shipman (BS) using Sigmund’s sputtering theory [9][10]. These models consider both erosion of the

• material than atomic beams, the high energy density when a cluster interacts with a surface, and nonlinear sputtering effects [13]. One of the most prominent properties of cluster beams is the smoothing effect on moderately rough surfaces [14]. The smoothing effect takes place at normal incidence of the

• lower than that for monoatomic beams [1][8][15]. The fast ripple formation by cluster irradiation can be a result of the more effective sputtering (excavation) processes by cluster ions described above. An influence of the accelerating voltage on the ripple formation is also revealed. Experiments have

Rational design of block copolymer self-assemblies in photodynamic therapy

• Maxime Demazeau,
• Laure Gibot,
• Anne-Françoise Mingotaud,
• Patricia Vicendo,
• Clément Roux and
• Barbara Lonetti

Beilstein J. Nanotechnol. 2020, 11, 180–212, doi:10.3762/bjnano.11.15

Advanced hybrid nanomaterials

• Andreas Taubert,
• Fabrice Leroux,
• Pierre Rabu and
• Verónica de Zea Bermudez

Beilstein J. Nanotechnol. 2019, 10, 2563–2567, doi:10.3762/bjnano.10.247

• electronic devices” [29]. A combination of deposition techniques was used, chemical vapor deposition for parylene and RF-magnetron sputtering for silver nanoparticles. The content and size of the latter influences the dielectric characteristics of the resulting hybrid films. Such devices may find application

Multiwalled carbon nanotube based aromatic volatile organic compound sensor: sensitivity enhancement through 1-hexadecanethiol functionalisation

• Nadra Bohli,
• Meryem Belkilani,
• Juan Casanova-Chafer,
• Eduard Llobet and
• Adnane Abdelghani

Beilstein J. Nanotechnol. 2019, 10, 2364–2373, doi:10.3762/bjnano.10.227

• substrates. They were then decorated with gold nanoparticles via a sputtering technique with a Sputtering ATC Orion 8-HV-AJA International machine [19]. This technique consists of bombarding the surface of a gold disc by a plasma beam, enabling the nanoparticles to cling to the walls of the MWCNTs under the

• characterisation Transmission electron microscopy characterisation In order to carry out high-resolution transmission electron microscope characterisation, MWCNTs were deposited onto a silicon substrate. Then, a sputtering process was conducted to deposit the Au nanoparticles. Afterwards, Au-decorated MWCNTs were

• distribution. We must point out though, that as the sputtering deposition technique only applies to the most exposed surfaces, a shadowing effect is also observed. This effect is generally observed for porous substrates, where sputtering only reaches the outermost surface and the topmost areas of the pore

Integration of sharp silicon nitride tips into high-speed SU8 cantilevers in a batch fabrication process

• Nahid Hosseini,
• Matthias Neuenschwander,
• Oliver Peric,
• Santiago H. Andany,
• Jonathan D. Adams and
• Georg E. Fantner

Beilstein J. Nanotechnol. 2019, 10, 2357–2363, doi:10.3762/bjnano.10.226

• separate the SU8 cantilevers from the wafer. The silicon oxide layer on the tips is then stripped using buffered hydrofluoric acid. The process is completed by titanium–gold (5–20 nm) sputtering on the chip-body side of the cantilevers. This layer serves as the reflective metal coating required for the

Synthesis of highly active ETS-10-based titanosilicate for heterogeneously catalyzed transesterification of triglycerides

• Muhammad A. Zaheer,
• David Poppitz,
• Khavar Feyzullayeva,
• Marianne Wenzel,
• Jörg Matysik,
• Radomir Ljupkovic,
• Aleksandra Zarubica,
• Alexander A. Karavaev,
• Andreas Pöppl,
• Roger Gläser and
• Muslim Dvoyashkin

Beilstein J. Nanotechnol. 2019, 10, 2039–2061, doi:10.3762/bjnano.10.200

Facile synthesis of carbon nanotube-supported NiO//Fe₂O₃ for all-solid-state supercapacitors

• Shengming Zhang,
• Xuhui Wang,
• Yan Li,
• Xuemei Mu,
• Yaxiong Zhang,
• Jingwei Du,
• Guo Liu,
• Xiaohui Hua,
• Yingzhuo Sheng,
• Erqing Xie and
• Zhenxing Zhang

Beilstein J. Nanotechnol. 2019, 10, 1923–1932, doi:10.3762/bjnano.10.188

• . deposited iron oxide on CNTs by atomic layer deposition (ALD) and the obtained CNTs@Fe2O3 presented a specific capacitance of 580.6 F·g−1 at 5 A·g−1 [21]. Zhang et al. used magnetron sputtering to prepare sandwich-like CNT@Fe2O3@C structures, and the composite exhibited a specific capacitance of 787.5 F·g−1

Oblique angle deposition of nickel thin films by high-power impulse magnetron sputtering

• Hamidreza Hajihoseini,
• Movaffaq Kateb,
• Snorri Þorgeir Ingvarsson and
• Jon Tomas Gudmundsson

Beilstein J. Nanotechnol. 2019, 10, 1914–1921, doi:10.3762/bjnano.10.186

• -100 44, Stockholm, Sweden 10.3762/bjnano.10.186 Abstract Background: Oblique angle deposition is known for yielding the growth of columnar grains that are tilted in the direction of the deposition flux. Using this technique combined with high-power impulse magnetron sputtering (HiPIMS) can induce

• unique properties in ferromagnetic thin films. Earlier we have explored the properties of polycrystalline and epitaxially deposited permalloy thin films deposited under 35° tilt using HiPIMS and compared it with films deposited by dc magnetron sputtering (dcMS). The films prepared by HiPIMS present lower

• properties for some important technological applications in addition to the ability to fill high aspect ratio trenches and coating on cutting tools with complex geometries. Keywords: glancing angle deposition (GLAD); high-power impulse magnetron sputtering (HiPIMS); oblique angle deposition; magnetron