Nanoarchitectonics with cetrimonium bromide on metal nanoparticles for linker-free detection of toxic metal ions and catalytic degradation of 4-nitrophenol

• Akash Kumar and
• Raja Gopal Rayavarapu

Beilstein J. Nanotechnol. 2024, 15, 1312–1332, doi:10.3762/bjnano.15.106

• laborious and requires precious metals such as palladium and platinum as catalysts [20]. Colorimetric detection methods have attracted attention because of their advantages, including simplicity, sensitivity, visualization, and real-time detection, while other methods often require expensive instrumentation

New design of operational MEMS bridges for measurements of properties of FEBID-based nanostructures

• Bartosz Pruchnik,
• Krzysztof Kwoka,
• Ewelina Gacka,
• Dominik Badura,
• Piotr Kunicki,
• Andrzej Sierakowski,
• Paweł Janus,
• Tomasz Piasecki and
• Teodor Gotszalk

Beilstein J. Nanotechnol. 2024, 15, 1273–1282, doi:10.3762/bjnano.15.103

• (Si3N4) layer was deposited via CVD. The 40 nm thick platinum paths were then patterned by lift-off photolithography. The opMEMS bridge body was defined photolithographically with a feature size of 2 µm, etched by dry oxygen plasma etching (DRIE) and then released by KOH anisotropic wet silicon etching

• . The silicon edges under the opMEMS bridge bases were defined to be vertical and precisely located, thanks to the lattice orientation. The opMEMS were 600 μm long, 100 μm wide, and 80 nm thick, with 40 nm of silicon nitride body and 40 nm of platinum paths on top. To reduce the stiffness of the opMEMS

• (GIS) for the supply of precursors required in the FEBID processes. In the experiments carried out, trimethyl(methylcyclopentadienyl)platinum(IV) (MeCpPtMe3) was used to deposit the Pt(C) material. Microfabrication of nanostructures and modification of opMEMS, both mechanically and electrically, is

A low-kiloelectronvolt focused ion beam strategy for processing low-thermal-conductance materials with nanoampere currents

• Annalena Wolff,
• Nico Klingner,
• William Thompson,
• Yinghong Zhou,
• Jinying Lin and
• Yin Xiao

Beilstein J. Nanotechnol. 2024, 15, 1197–1207, doi:10.3762/bjnano.15.97

• , TEM lamellae for 5 keV ion energy was prepared using the Quanta 200 3D and compared to the previously reported results [17]. First, a protective platinum layer was deposited onto the desired area using 5 kV and 0.23 nA. The cross sections were cut using 5 kV acceleration voltage with 1.4 nA ion beam

Direct electron beam writing of silver using a β-diketonate precursor: first insights

• Katja Höflich,
• Krzysztof Maćkosz,
• Chinmai S. Jureddy,
• Aleksei Tsarapkin and
• Ivo Utke

Beilstein J. Nanotechnol. 2024, 15, 1117–1124, doi:10.3762/bjnano.15.90

• obtained [34]. For planar deposits, similar microstructures were obtained during platinum deposition using Pt(η5-CpMe)Me3 [35] and ruthenium deposition using (EtCp)2Ru [36], both in combination with post-deposition purification employing electron beam irradiation in a water atmosphere. For the case of

Atomistic insights into the morphological dynamics of gold and platinum nanoparticles: MD simulations in vacuum and aqueous media

• Evangelos Voyiatzis,
• Eugenia Valsami-Jones and
• Antreas Afantitis

Beilstein J. Nanotechnol. 2024, 15, 995–1009, doi:10.3762/bjnano.15.81

• Evangelos Voyiatzis Eugenia Valsami-Jones Antreas Afantitis NovaMechanics Ltd., Nicosia 1070, Cyprus School of Geography, Earth and Environmental Sciences, University of Birmingham, Birmingham B15 2TT, United Kingdom 10.3762/bjnano.15.81 Abstract The thermal response of gold and platinum

• , the transition temperature from a melted/amorphous to a highly crystalline state varies considerably with NP size. For larger NPs, the transition temperature is almost diameter-independent, yet it differs considerably from the transition temperature of the respective bulk materials. The platinum NPs

• employed to study other metallic and metal oxide nanomaterials. Keywords: crystallization; gold; molecular dynamics; nanoparticles; platinum; Introduction Nanomaterials, that is, materials with dimensions in the range of 1–100 nm [1][2], are central to a variety of developments in science and technology

Recent progress on field-effect transistor-based biosensors: device perspective

• Billel Smaani,
• Fares Nafa,
• Mohamed Salah Benlatrech,
• Ismahan Mahdi,
• Hamza Akroum,
• Mohamed walid Azizi,
• Khaled Harrar and
• Sayan Kanungo

Beilstein J. Nanotechnol. 2024, 15, 977–994, doi:10.3762/bjnano.15.80

• was employed for the fabrication of the NW structure [92]. Moreover, this device is gated by a back gate and one or two platinum side gates via a liquid which has been characterized for possible implementation in reliable sensing applications. This biosensor uses HfO2 as a high-k gate dielectric

Water-assisted purification during electron beam-induced deposition of platinum and gold

• Cristiano Glessi,
• Fabian A. Polman and
• Cornelis W. Hagen

Beilstein J. Nanotechnol. 2024, 15, 884–896, doi:10.3762/bjnano.15.73

• beam-induced deposition (FEBID). It was recently achieved for gold deposits by the co-injection of a water precursor and the gold precursor Au(tfac)Me2. In this work results are reported, using the same approach, on a different gold precursor, Au(acac)Me2, as well as the frequently used platinum

• precursor MeCpPtMe3. As a water precursor MgSO4·7H2O was used. The purification during deposition led to a decrease of the carbon-to-gold ratio (in atom %) from 2.8 to 0.5 and a decrease of the carbon-to-platinum ratio (in atom %) from 6–7 to 0.2. The purification was done in a regular scanning electron

• microscope using commercially available components and chemicals, which paves the way for a broader application of direct etching-assisted FEBID to obtain pure metallic structures. Keywords: FEBID; gold; nanofabrication; platinum; purification; Introduction Focused electron beam-induced deposition (FEBID

Exploring surface charge dynamics: implications for AFM height measurements in 2D materials

• Mario Navarro-Rodriguez,
• Andres M. Somoza and
• Elisa Palacios-Lidon

Beilstein J. Nanotechnol. 2024, 15, 767–780, doi:10.3762/bjnano.15.64

• modulation mode (FM-KPFM) with an AC voltage of 700 mV at 7 kHz using platinum-coated silicon tips (Olympus AC240TM-R3, k = 2 N/m and f0 = 70 kHz). Using a dual lock-in amplifier (Zurich instruments, HF2LI), in addition to the KPFM channel, which provides information on the sample's SP, the 2ωelec

Level set simulation of focused ion beam sputtering of a multilayer substrate

• Alexander V. Rumyantsev,
• Nikolai I. Borgardt,
• Roman L. Volkov and
• Yuri A. Chaplygin

Beilstein J. Nanotechnol. 2024, 15, 733–742, doi:10.3762/bjnano.15.61

• beam workstation Helios Nanolab 650. Both types of test structures were fabricated using 30 kV accelerating voltage and an ion beam current of I = 900 pA. The chamber pressure was not higher then 10−6 mbar. A layer of platinum and amorphous carbon (Pt + a-C) was deposited onto the manufactured

Simultaneous electrochemical determination of uric acid and hypoxanthine at a TiO₂/graphene quantum dot-modified electrode

• Vu Ngoc Hoang,
• Dang Thi Ngoc Hoa,
• Nguyen Quang Man,
• Le Vu Truong Son,
• Le Van Thanh Son,
• Vo Thang Nguyen,
• Le Thi Hong Phong,
• Ly Hoang Diem,
• Kieu Chan Ly,
• Ho Sy Thang and
• Dinh Quang Khieu

Beilstein J. Nanotechnol. 2024, 15, 719–732, doi:10.3762/bjnano.15.60

• electrode (GCE, 3 mm diameter), a platinum wire auxiliary electrode, and a Ag/AgCl reference electrode was used. Electrolyte solutions were prepared using doubly distilled water. Britton–Robinson (BR) buffer solutions with pH between 2 and 6 were prepared by mixing boric acid solution, phosphoric acid

Laser synthesis of nanoparticles in organic solvents – products, reactions, and perspectives

• Theo Fromme,
• Sven Reichenberger,
• Katharine M. Tibbetts and
• Stephan Barcikowski

Beilstein J. Nanotechnol. 2024, 15, 638–663, doi:10.3762/bjnano.15.54

• % [68][69], while platinum surfaces are partially oxidized with 20–73% [70][92], and nickel particles are completely oxidized [70]. This was further investigated by Kalus et al., who ablated seven different metals (Au, Pt, Ag, Cu, Fe, Ti, and Al) in water while quantifying the formed hydrogen and oxygen

Fabrication of nanocrystal forms of ᴅ-cycloserine and their application for transdermal and enteric drug delivery systems

• Hsuan-Ang Tsai,
• Tsai-Miao Shih,
• Theodore Tsai,
• Jhe-Wei Hu,
• Yi-An Lai,
• Jui-Fu Hsiao and
• Guochuan Emil Tsai

Beilstein J. Nanotechnol. 2024, 15, 465–474, doi:10.3762/bjnano.15.42

• double-coated carbon conductive tape and DCS nanocrystals were suspended in ethanol (Merck KGaA) at 10 mg/mL, put on the double-coated carbon conductive tape, and coated with platinum using an auto-fine coater for better electrical conduction. For the XRPD analysis, commercial DCS powder and DCS

Classification and application of metal-based nanoantioxidants in medicine and healthcare

• Nguyen Nhat Nam,
• Nguyen Khoi Song Tran,
• Tan Tai Nguyen,
• Nguyen Ngoc Trai,
• Nguyen Phuong Thuy,
• Hoang Dang Khoa Do,
• Nhu Hoa Thi Tran and
• Kieu The Loan Trinh

Beilstein J. Nanotechnol. 2024, 15, 396–415, doi:10.3762/bjnano.15.36

• is caused by protein denaturation at high temperatures. Impressively, Co3O4 nanomaterials with different morphologies (nanoplates, nanorods, and nanocubes) exhibited the highest relative activity at very high pH (pH 9) and temperature (90 °C) [39]. Similar results were also reported for platinum

• . Subsequently, V−OH recovers to V=O by reacting with another H2O2 in the presence of GSH [43][44][45]. Recently, Liu et at. constructed a trimetallic alloy nanozyme of gold, copper, and platinum, which exhibits multiple enzyme activities including that of GPx [46]. In this nanocomposite, platinum and copper

• reported. Most of them employ transition metals such as iron [70], copper [71], cobalt [72], gold [73], manganese [74], platinum [75], or cerium [76] as main elements. Most transition metals have various oxidation states allowing them to generate cycles of redox reactions that are involved in superoxide

On the mechanism of piezoresistance in nanocrystalline graphite

• Sandeep Kumar,
• Simone Dehm and
• Ralph Krupke

Beilstein J. Nanotechnol. 2024, 15, 376–384, doi:10.3762/bjnano.15.34

• smaller grain sizes and diminishes with larger grains. The mechanism has been proposed as a cause of plastic deformation in metals. Wang et al. showed for a platinum nanocrystalline film [42] that the rotation due to strain at room temperature does not occur because of cross-grain gliding, GB sliding, or

Design, fabrication, and characterization of kinetic-inductive force sensors for scanning probe applications

• August K. Roos,
• Ermes Scarano,
• Elisabet K. Arvidsson,
• Erik Holmgren and
• David B. Haviland

Beilstein J. Nanotechnol. 2024, 15, 242–255, doi:10.3762/bjnano.15.23

• -induced deposition of platinum. Finally, we present measurements that characterize the spread of mechanical resonant frequency, the temperature dependence of the microwave resonance, and the sensor’s operation as an electromechanical transducer of force. Keywords: atomic force microscopy; force sensing

• microscopy (SPM), the tip plays a fundamental role in the achievable lateral resolution of the image. The focused electron-beam induced deposition (FEBID) [34] technique has been adapted to fabricate tips for SPM, for example, to enhance commercial platinum–iridium alloy (Pt-Ir)-coated conductive tips [35

• an electron-beam deposited platinum tip on the released Si-N cantilever of one chip. The tip has total height in the range of 1–2 μm. (b) An SEM image of the reverse cone structure, deposited using multiple layers of platinum. Note the larger connection to the Nb-Ti-N thin film to the left of the tip

In situ optical sub-wavelength thickness control of porous anodic aluminum oxide

• Aleksandrs Dutovs,
• Raimonds Popļausks,
• Oskars Putāns,
• Vladislavs Perkanuks,
• Aušrinė Jurkevičiūtė,
• Tomas Tamulevičius,
• Uldis Malinovskis,
• Iryna Olyshevets,
• Donats Erts and
• Juris Prikulis

Beilstein J. Nanotechnol. 2024, 15, 126–133, doi:10.3762/bjnano.15.12

• samples at constant 40 V potential. Platinum cathode and single crystal Al(100) (MTI Corp. mcALa101010) anode were immersed in 0.3 M oxalic acid electrolyte inside a multiwalled container with a transparent optical window. The container was placed on a magnetic stirrer and cooled to 5 °C. The reflectance

New application of bimetallic Ag/Pt nanoplates in a colorimetric biosensor for specific detection of E. coli in water

• Azam Bagheri Pebdeni,
• Mohammad N. AL-Baiati and
• Morteza Hosseini

Beilstein J. Nanotechnol. 2024, 15, 95–103, doi:10.3762/bjnano.15.9

• detection is described using a silver/platinum nanoplate (Ag/Pt NPL) that interacts with an oligonucleotide aptamer as a bioreceptor. The size of the Ag/Pt NPLs was about 42 nm according to the FE-SEM images. The EDS result indicates that a thin layer of Pt ions was coated on the surface of the Ag NPLs

• ; biosensor; detection; E. coli; peroxidase activity; silver/platinum nanoplate; Introduction One of the most dangerous foodborne infections is caused by E. coli. It can induce hemorrhagic colitis, hemolytic uremic syndrome, and thrombocytopenic purpura. E. coli is responsible for more than 2 million acute

• peroxidase activity of Ag/Pt NPLs is substantially greater than those of silver or platinum alone. When compared to Ag NPLs or Pt NPLs alone, the bimetallic NPLs demonstrated higher peroxidase-like activity. We synthesized Ag NPLs and Pt NPLs under the same conditions as bimetallic NPLs. After adding TMB and

A combined gas-phase dissociative ionization, dissociative electron attachment and deposition study on the potential FEBID precursor [Au(CH₃)₂Cl]₂

• Elif Bilgilisoy,
• Ali Kamali,
• Thomas Xaver Gentner,
• Gerd Ballmann,
• Sjoerd Harder,
• Hans-Peter Steinrück,
• Hubertus Marbach and
• Oddur Ingólfsson

Beilstein J. Nanotechnol. 2023, 14, 1178–1199, doi:10.3762/bjnano.14.98

• purification studies [62][63], thin layer exposure to electrons at approx. 500 eV [64][65], gas-phase studies under single collision condition [28][66], and FEBID under HV and UHV conditions [30][60]. Most noticeably, platinum precursors Pt(CO)2X2 (X = Cl, Br) have been studied with respect to FEBID and their

A multi-resistance wide-range calibration sample for conductive probe atomic force microscopy measurements

• François Piquemal,
• Khaled Kaja,
• Pascal Chrétien,
• José Morán-Meza,
• Frédéric Houzé,
• Christian Ulysse and
• Abdelmounaim Harouri

Beilstein J. Nanotechnol. 2023, 14, 1141–1148, doi:10.3762/bjnano.14.94

• imaging and spectroscopic (i.e., I–V curves) modes with a 1% achievable relative uncertainty level in the range between 106 Ω and 5 × 1010 Ω. The protocols adopted in this study highlight several routes for further improvements. Using platinum as metallic material instead of gold for the small electrode

Nanoarchitectonics of photothermal materials to enhance the sensitivity of lateral flow assays

• Elangovan Sarathkumar,
• Rajasekharan S. Anjana and
• Ramapurath S. Jayasree

Beilstein J. Nanotechnol. 2023, 14, 988–1003, doi:10.3762/bjnano.14.82

• particle size from 50 to 4.98 nm. In another study, the size-dependent photothermal conversion efficiency of platinum nanomaterials was studied by Depciuch et al. for cancer therapy. Spherical platinum nanoparticles with diameters of 2 and 80 nm were studied regarding the photothermal activity in colon

• Chemical Society. This content is not subject to CC BY 4.0.). Photothermal conversion efficiency of 2 and 8 nm platinum nanoparticles. Orange and the red line represent 2 and 80 nm Pt nanoparticles respectively and their calculated abs/ext ratio (B). (Figure 5B was reprinted from [54], Photodiagnosis and

• Photodynamic Therapy, vol. 29, by J. Depciuch; M. Stec; B. Klebowski; A. Maximenko; E. Drzymała; J. Baran; M. Parlinska-Wojtan, “Size effect of platinum nanoparticles in simulated anticancer photothermal therapy“, article no. 101594, Copyright (2019), with permission from Elsevier. This content is not subject

Nanostructured lipid carriers containing benznidazole: physicochemical, biopharmaceutical and cellular in vitro studies

• Giuliana Muraca,
• María Esperanza Ruiz,
• Rocío C. Gambaro,
• Sebastián Scioli-Montoto,
• María Laura Sbaraglini,
• Gisel Padula,
• José Sebastián Cisneros,
• Cecilia Yamil Chain,
• Vera A. Álvarez,
• Cristián Huck-Iriart,
• Guillermo R. Castro,
• María Belén Piñero,
• Matias Ildebrando Marchetto,
• Catalina Alba Soto,
• Germán A. Islan and
• Alan Talevi

Beilstein J. Nanotechnol. 2023, 14, 804–818, doi:10.3762/bjnano.14.66

• . A Platinum EPS C8 (150 mm × 4.6 mm, 5 μm, GraceTM, Columbia, MD, USA) column was used; the mobile phase consisted of a mixture of methanol and 0.02% phosphoric acid solution (60:40) for a final pH of 2.5. The system was operated isocratically at a 1.0 mL/min flow rate and the detection was performed

• Instruments, New Castle, DE, USA). Freeze dried formulations of approximately 10 mg were accurately weighed in a platinum pan. Measurements were performed from room temperature to 600 °C at a heating rate of 10 °C/min under nitrogen atmosphere to avoid thermo-oxidative degradation. Attenuated total reflection

A graphene quantum dots–glassy carbon electrode-based electrochemical sensor for monitoring malathion

• Sanju Tanwar,
• Aditi Sharma and
• Dhirendra Mathur

Beilstein J. Nanotechnol. 2023, 14, 701–710, doi:10.3762/bjnano.14.56

• obtained from a Bruker AFM analyzer atomic force microscope and a FEI Tecnai G2 20 S-TWIN transmission electron microscope. Electrochemical measurements GQDs/GCE, Ag/AgCl, and a platinum wire were used as working, reference, and counter electrode, respectively, in all electrochemical experiments, conducted

SERS performance of GaN/Ag substrates fabricated by Ag coating of GaN platforms

• Magdalena A. Zając,
• Bogusław Budner,
• Malwina Liszewska,
• Bartosz Bartosewicz,
• Łukasz Gutowski,
• Jan L. Weyher and
• Bartłomiej J. Jankiewicz

Beilstein J. Nanotechnol. 2023, 14, 552–564, doi:10.3762/bjnano.14.46

• [32]. Calculations were based on the intensity of the peak at 1078 cm−1, which is the most intense of all peaks in the pMBA spectrum. To determine EFs, a Raman measurement of pMBA adsorbed on the surface of a polished platinum plate was additionally made. The procedure for the analyte deposition on

• the SERS substrates and the platinum plate was the same [32]. The EF values calculated for fabricated SERS substrates are given in Table 3. The SERS spectra of pMBA adsorbed on GaN/Ag substrates fabricated using MS are shown in Figure 6. The substrates fabricated by this method provide similar average

• accumulations at each point for a polished platinum plate. The SERS spectra were acquired from at least 100 points. All collected spectra were processed in the WiRE 5.5 software and then averaged using the CasaXPS software. The SERS measurements were made on SERS substrates that were first embedded in 0.001 M

Evaluation of electrosynthesized reduced graphene oxide–Ni/Fe/Co-based (oxy)hydroxide catalysts towards the oxygen evolution reaction

• Karolina Cysewska,
• Marcin Łapiński,
• Marcin Zając,
• Jakub Karczewski,
• Piotr Jasiński and
• Sebastian Molin

Beilstein J. Nanotechnol. 2023, 14, 420–433, doi:10.3762/bjnano.14.34

• , the substrates were cleaned ultrasonically in distilled water (5 min) and acetone (5 min). The reference and counter electrodes were Ag/AgCl (4 M KCl) and platinum mesh, respectively. Distilled water was used for the solutions. The measurement temperature was controlled by a thermostat (Julabo F12

Plasmonic nanotechnology for photothermal applications – an evaluation

• A. R. Indhu,
• L. Keerthana and
• Gnanaprakash Dharmalingam

Beilstein J. Nanotechnol. 2023, 14, 380–419, doi:10.3762/bjnano.14.33

• elements, nanospheres of gold, silver, platinum, cobalt, zinc, nickel, titanium, copper, aluminium, molybdenum, vanadium, and palladium have been analysed [98]. Although there were assumptions of homogeneity, sphericity, and no interaction between particles, the Mie theory-based scattering cross sections