Ion beam processing of DNA origami nanostructures

• Leo Sala,
• Agnes Zerolová,
• Violaine Vizcaino,
• Alain Mery,
• Alicja Domaracka,
• Hermann Rothard,
• Philippe Boduch,
• Dominik Pinkas and
• Jaroslav Kocišek

Beilstein J. Nanotechnol. 2024, 15, 207–214, doi:10.3762/bjnano.15.20

• , ENSICAEN, UNICAEN, CEA, CNRS, CIMAP, Boulevard Henri Becquerel, BP 5133, 14070, Caen cedex 5, France Electron Microscopy Center, Institute of Molecular Genetics of the CAS, Vídenská 1083, 142 20, Prague, Czech Republic 10.3762/bjnano.15.20 Abstract DNA origami nanostructures are emerging as a bottom-up

• in the present context are works on the use of DNA origami nanostructures in top-down or bottom-up nanopatterning approaches [7][8][9][10]. So far, DNA origami has been proposed only as a resist or as a platform to precisely arrange nanostructure precursors in lithography [11][12][13]. Incorporating

• of various factors concerning material properties and the parameters of the impinging ion beam [22][23][24][25]. While crucial for modern nanotechnology, SHI cause severe damage to DNA [26][27][28]. This challenges the use of DNA-based nanomaterials for combined top-down and bottom-up nanoprocessing

Assessing phytotoxicity and tolerance levels of ZnO nanoparticles on Raphanus sativus: implications for widespread adoptions

• Pathirannahalage Sahan Samuditha,
• Nadeesh Madusanka Adassooriya and
• Nazeera Salim

Beilstein J. Nanotechnol. 2024, 15, 115–125, doi:10.3762/bjnano.15.11

• , which may be top-down or bottom-up approaches, has facilitated the synthesis of nanoparticles of differing shapes, sizes and properties [11]. When considering zinc oxide nanoparticles (ZnO NPs) in particular, their low toxicity, high biocompatibility, and low cost [12] have enabled them to be applied as

Spatial variations of conductivity of self-assembled monolayers of dodecanethiol on Au/mica and Au/Si substrates

• Julian Skolaut,
• Jędrzej Tepper,
• Federica Galli,
• Wulf Wulfhekel and
• Jan M. van Ruitenbeek

Beilstein J. Nanotechnol. 2023, 14, 1169–1177, doi:10.3762/bjnano.14.97

• /Si; conductive atomic force microscopy; dodecanethiol; self-assembled monolayers; Introduction For decades, the need for miniaturization of electronics has pushed the research field into the direction of bottom-up, rather than top-down, approaches. In this research field, molecular electronics [1][2

• ][3] has always held a central role, as the flexibility and control over the structure of molecules is unmatched. One of the fundamental parts of devices employing a bottom-up approach combined with molecular electronics is comprised of metal electrodes and molecular layers deposited onto them. For

Nanoarchitectonics for advanced applications in energy, environment and biology: Method for everything in materials science

• Katsuhiko Ariga

Beilstein J. Nanotechnol. 2023, 14, 738–740, doi:10.3762/bjnano.14.60

• nanotechnology, which pioneered the science at that length scale. Such methodologies were also touched upon in the bottom-up fabrication of materials using supramolecular chemistry and other methods [7][8]. Nanoarchitectonics encompasses these methods and integrates them into a broader field of research

Humidity-dependent electrical performance of CuO nanowire networks studied by electrochemical impedance spectroscopy

• Jelena Kosmaca,
• Juris Katkevics,
• Jana Andzane,
• Raitis Sondors,
• Liga Jasulaneca,
• Raimonds Meija,
• Kiryl Niherysh,
• Yelyzaveta Rublova and
• Donats Erts

Beilstein J. Nanotechnol. 2023, 14, 683–691, doi:10.3762/bjnano.14.54

• ]. Copper oxide (CuO) nanowires are excellent candidates for applications in such devices owing to the inexpensive, simple and scalable bottom-up synthesis, and robust physical properties [7][8][9]. A high specific surface area of nanowires and a p-type semiconductor structure are suggested for highly

Nanoarchitectonics to entrap living cells in silica-based systems: encapsulations with yolk–shell and sepiolite nanomaterials

• Celia Martín-Morales,
• Jorge Fernández-Méndez,
• Pilar Aranda and
• Eduardo Ruiz-Hitzky

Beilstein J. Nanotechnol. 2023, 14, 522–534, doi:10.3762/bjnano.14.43

• Biological Sciences, Complutense University of Madrid (UCM), C/ José Antonio Novais 12, 28040 Madrid, Spain 10.3762/bjnano.14.43 Abstract In the present work, the bottom-up fabrication of biohybrid materials using a nanoarchitectonics approach has been applied to entrap living cells. Unicellular

• biological functions that can be effectively manipulated through the inorganic components, with potential impact on leading applications within the fields of chemical synthesis and catalysis, energy, environment, and biomedicine. Examples of bionanohybrids include the bottom-up fabrication of

• with transparency, easy tuning, and low energy requirements of the bottom-up synthesis, opens the way for the development of novel biohybrid systems with a wide range of applications, from biological preservation of living cells to the development of novel whole-cell bioinorganic catalytic materials

Molecular nanoarchitectonics: unification of nanotechnology and molecular/materials science

• Katsuhiko Ariga

Beilstein J. Nanotechnol. 2023, 14, 434–453, doi:10.3762/bjnano.14.35

• ]. Bottom-up synthesis of materials using molecular and ionic units, which is widely used in supramolecular chemistry and coordination chemistry, is now being elucidated by nanotechnology under observation of actual materials. Thus, the contribution of nanotechnology to the creation of materials cannot be

• various low-dimensional nanostructures will be synthesized by this on-surface synthetic nanoarchitectonics. The bottom-up synthesis of graphene nanoribbons on surfaces has attracted much attention due to their high electronic, optical, and magnetic properties. Sakaguchi and co-workers have synthesized

• . Nanoarchitectonics of graphene nanoribbon heterojunctions has the potential to be a major technological breakthrough because of the rational design and by virtue of the extraordinary structural and electronic properties of such heterojunctions. However, graphene nanoribbon heterojunction structures made by bottom-up

Bismuth-based nanostructured photocatalysts for the remediation of antibiotics and organic dyes

• Akeem Adeyemi Oladipo and
• Faisal Suleiman Mustafa

Beilstein J. Nanotechnol. 2023, 14, 291–321, doi:10.3762/bjnano.14.26

• ][121][122][123][124], so they are not covered in this review. In general, top-down approaches or bottom-up approaches can be used to synthesise Bi-based nanostructured materials using traditional solid-state methods as well as wet-chemical methods. Solid-state methods are typically high-energy methods

Structural, optical, and bioimaging characterization of carbon quantum dots solvothermally synthesized from o-phenylenediamine

• Zoran M. Marković,
• Milica D. Budimir,
• Martin Danko,
• Dušan D. Milivojević,
• Pavel Kubat,
• Danica Z. Zmejkoski,
• Vladimir B. Pavlović,
• Marija M. Mojsin,
• Milena J. Stevanović and
• Biljana M. Todorović Marković

Beilstein J. Nanotechnol. 2023, 14, 165–174, doi:10.3762/bjnano.14.17

• ; Introduction Carbon quantum dots (CQDs) as a novel class of carbon nanomaterials can be prepared by using different methods and precursors [1][2]. Most of the common preparation procedures are bottom-up methods [3][4]. Depending on the used precursors and solvents, the structure of the CQDs can be modified

Solvent-induced assembly of mono- and divalent silica nanoparticles

• Bin Liu,
• Etienne Duguet and
• Serge Ravaine

Beilstein J. Nanotechnol. 2023, 14, 52–60, doi:10.3762/bjnano.14.6

• assembled in a bottom-up fashion [1][2][3][4][5]. Among all the existing synthetic routes permitting to imbue functionality into a colloidal suspension, those dedicated to the formation of patchy particles have received particular attention [6][7][8][9][10]. Indeed, several generic models including the

Straight roads into nowhere – obvious and not-so-obvious biological models for ferrophobic surfaces

• Wilfried Konrad,
• Christoph Neinhuis and
• Anita Roth-Nebelsick

Beilstein J. Nanotechnol. 2022, 13, 1345–1360, doi:10.3762/bjnano.13.111

• “bottom-up” (or “biology push”) approach, denotes the introduction of identified biological functional systems into applied sciences, by directly suggesting possible technical applications. The second one, the “top-down” (or “technology pull”) approach, is initiated by a defined technical problem for

• potential is identified and described, biological systems migrate from the bottom-up realm to the top-down portfolio, together with their originally recognised application potential. Tapping this top-down portfolio is an attractive modus operandi because it appears to guarantee a straightforward and swift

• the winding path of a project originally initiated by a technical problem that appeared to be solved straightforwardly by focusing on water-repellent biological surfaces (i.e., adopting a bottom-up strategy). As it turned out, however, the way to a finally successful prototype was not to follow the

Recent advances in green carbon dots (2015–2022): synthesis, metal ion sensing, and biological applications

• Aisha Kanwal,
• Naheed Bibi,
• Sajjad Hyder,
• Arif Muhammad,
• Hao Ren,
• Jiangtao Liu and
• Zhongli Lei

Beilstein J. Nanotechnol. 2022, 13, 1068–1107, doi:10.3762/bjnano.13.93

• synthetic pathways for the formation of CDs, that is, “top-down” and “bottom-up” methods. In the top-down method, large carbon structures (such as carbon nanotubes or graphite) are decomposed into CDs. The top-down methods include arc discharge, laser abrasion [24], chemical and electrochemical oxidation

• , and ultrasonic synthesis. In the bottom-up methods, CDs are formed from molecular precursors by various techniques such as hydrothermal treatment [25][26][27][28][29], microwave synthesis [30], and pyrolysis [31]. A tremendous amount of work has been done regarding the synthesis and different

• material is oxidized and broken down into CDs using oxidants such as sulfuric acid and nitric acid. As green methods are limited regarding the raw materials, the “top-down” method is not very common in green approaches [3][50]. The “bottom-up” method consist of carbonization of smaller organic molecules

Experimental and theoretical study of field-dependent spin splitting at ferromagnetic insulator–superconductor interfaces

• Peter Machon,
• Michael J. Wolf,
• Detlef Beckmann and
• Wolfgang Belzig

Beilstein J. Nanotechnol. 2022, 13, 682–688, doi:10.3762/bjnano.13.60

• density of states of the superconducting film by tunnel spectroscopy. Results and Discussion Theory The setup of the underlying experiment is shown in Figure 1a. It consists (bottom-up) of an EuS substrate, a superconducting (Al) film, and a normal metal film that is separated from the superconductor by

Antibacterial activity of a berberine nanoformulation

• Hue Thi Nguyen,
• Tuyet Nhung Pham,
• Anh-Tuan Le,
• Nguyen Thanh Thuy,
• Tran Quang Huy and
• Thuy Thi Thu Nguyen

Beilstein J. Nanotechnol. 2022, 13, 641–652, doi:10.3762/bjnano.13.56

• ], particle size reduction [25], and encapsulation in nanoscale delivery systems [11]. Nanoscale BBR crystals can be formed using top-down technologies (ball mills, high-pressure homogenizers, microfluidic technology, and spray drying) or bottom-up technologies (evaporative precipitation of nanosuspension

Tubular glassy carbon microneedles with fullerene-like tips for biomedical applications

• Sharali Malik and
• George E. Kostakis

Beilstein J. Nanotechnol. 2022, 13, 455–461, doi:10.3762/bjnano.13.38

• the nanoarchitectonics concept of bottom-up creation of functional materials, we use methane rather than a polymer to form glassy carbon. Here we show that tubular glassy carbon microneedles with fullerene-like tips form when methane undergoes pyrolysis on a curved alumina surface. X-ray diffraction

Electrostatic pull-in application in flexible devices: A review

• Teng Cai,
• Yuming Fang,
• Yingli Fang,
• Ruozhou Li,
• Ying Yu and
• Mingyang Huang

Beilstein J. Nanotechnol. 2022, 13, 390–403, doi:10.3762/bjnano.13.32

• or bottom-up processes and, subsequently, their parameters are tested. In the latter, the pull-in effect of NWs is directly studied through atomic force microscopy or transmission electron microscopy using nanomanipulators. This allows one to explore different working states without having to

• et al. [8] made a CuO NWs switch, 3 µm long, 80 nm in diameter, and 120 nm in the gap, with a pull-in voltage of 12.5 V. Feng et al. [40] prepared SiC nanowire NEM switches using bottom-up techniques. The pull-in voltage ranges from one to several volts and the response time is below microseconds

Micro- and nanotechnology in biomedical engineering for cartilage tissue regeneration in osteoarthritis

• Zahra Nabizadeh,
• Mahmoud Nasrollahzadeh,
• Hamed Daemi,
• Mohamadreza Baghaban Eslaminejad,
• Ali Akbar Shabani,
• Mehdi Dadashpour,
• Majid Mirmohammadkhani and
• Davood Nasrabadi

Beilstein J. Nanotechnol. 2022, 13, 363–389, doi:10.3762/bjnano.13.31

Alcohol-perturbed self-assembly of the tobacco mosaic virus coat protein

• Ismael Abu-Baker and
• Amy Szuchmacher Blum

Beilstein J. Nanotechnol. 2022, 13, 355–362, doi:10.3762/bjnano.13.30

• ; Introduction Bottom-up fabrication of nanomaterials with precise control over the spatial arrangement of components is of great interest in nanotechnology [1][2]. A promising approach to this issue is the use of templates based on self-assembling biological materials, such as nucleic acids and proteins [3][4

Effect of lubricants on the rotational transmission between solid-state gears

• Huang-Hsiang Lin,
• Jonathan Heinze,
• Alexander Croy,
• Rafael Gutiérrez and
• Gianaurelio Cuniberti

Beilstein J. Nanotechnol. 2022, 13, 54–62, doi:10.3762/bjnano.13.3

• either solid-state gears or molecular gears, which are created by top-down approaches (e.g., using focused ion beams [23] or electron beams [24][25] to etch the substrate) or bottom-up approaches such as chemical synthesis [26][27]. The ultimate goal for those miniaturized gears is to implement nanoscale

Sputtering onto liquids: a critical review

• Anastasiya Sergievskaya,
• Adrien Chauvin and
• Stephanos Konstantinidis

Beilstein J. Nanotechnol. 2022, 13, 10–53, doi:10.3762/bjnano.13.2

• physicochemical characteristics is required for their applications in various fields on the industrial scale [15]. Generally, methods employed for the synthesis of NPs follow either the “top-down” or the “bottom-up” routes. On the one hand, in the “top-down” approach, a destructive technology is employed. The

• production starts from bulk materials that leach out systematically, leading to the generation of NPs. The starting material can be reduced in size using either a physical or a chemical route. On the other hand, the “bottom-up” approach, or self-assembly, refers to building up a structure atom-by-atom or

The effect of cobalt on morphology, structure, and ORR activity of electrospun carbon fibre mats in aqueous alkaline environments

• Markus Gehring,
• Tobias Kutsch,
• Osmane Camara,
• Alexandre Merlen,
• Hermann Tempel,
• Hans Kungl and
• Rüdiger-A. Eichel

Beilstein J. Nanotechnol. 2021, 12, 1173–1186, doi:10.3762/bjnano.12.87

• three main groups: electroplating, electroless plating, and bottom-up methods such as vapour deposition. Another way to introduce metals to a carbon fibre system in form of nanoparticles was reported by groups who prepared cobalt/cobalt oxide-decorated carbon nanofibres from electrospinning by adding a

• electrospinning are a convenient and promising material for air electrodes in metal–air batteries. These studies used the cobalt-enhanced fibre material either as a bottom-up catalyst material in aqueous alkaline systems [21][22] or as free-standing electrodes in non-aqueous systems with a lab-scale geometric

Self-assembly of amino acids toward functional biomaterials

• Huan Ren,
• Lifang Wu,
• Lina Tan,
• Yanni Bao,
• Yuchen Ma,
• Yong Jin and
• Qianli Zou

Beilstein J. Nanotechnol. 2021, 12, 1140–1150, doi:10.3762/bjnano.12.85

• nanostructures at both microscopic and macroscopic scales. Amino acids, as the smallest constituent of proteins and the smallest constituent in the bottom-up approach, are the smallest building blocks that can be self-assembled. The self-assembly of single amino acids has the advantages of low synthesis cost

• of all naturally occurring peptides and proteins [25]. Amino-acid-based nanostructures are self-assembled from the simplest building blocks in the biological system environment and are the smallest component of the bottom-up approach [26]. Amino acids and their derivatives can be self-assembled into

• interaction to construct a co-delivery system. Conclusion The self-assembly of biomolecules is based on the noncovalent interaction and the bottom-up combination of ordered 3D structures. Nanotechnology is the driving force of self-assembly, and it has made great contributions to the field of biology and

Molecular assemblies on surfaces: towards physical and electronic decoupling of organic molecules

• Sabine Maier and
• Meike Stöhr

Beilstein J. Nanotechnol. 2021, 12, 950–956, doi:10.3762/bjnano.12.71

• molecules, offering unique opportunities for the bottom-up assembly of novel carbon-based materials using on-surface chemistry [48][49]. However, the significantly reduced catalytic activity on non-metallic substrates requires exploring alternative reaction mechanisms beyond thermal activation, for example

Electromigration-induced formation of percolating adsorbate islands during condensation from the gaseous phase: a computational study

• Alina V. Dvornichenko,
• Vasyl O. Kharchenko and
• Dmitrii O. Kharchenko

Beilstein J. Nanotechnol. 2021, 12, 694–703, doi:10.3762/bjnano.12.55

• require free sites on the target layer. For the adsorbate concentration on the first growing layer for ft one gets: ft = k↓y(1 − x) − k↑x(1 − y), where y(r,t) is the adsorbate concentration on the second layer; k↑,↓ are the rates of bottom-up motion and vice versa, respectively. Next we assume, that the

Paper-based triboelectric nanogenerators and their applications: a review

• Jing Han,
• Nuo Xu,
• Yuchen Liang,
• Mei Ding,
• Junyi Zhai,
• Qijun Sun and
• Zhong Lin Wang

Beilstein J. Nanotechnol. 2021, 12, 151–171, doi:10.3762/bjnano.12.12

• process or to rotary screen printing, which enables a facile and high-throughput printing on curved surfaces. The deposition process assisted with soft stencils is another “bottom-up” method for the preparation of functional materials on flexible and irregular surfaces. Even though P-TENGs require