AFM as an analysis tool for high-capacity sulfur cathodes for Li–S batteries

• Renate Hiesgen,
• Seniz Sörgel,
• Rémi Costa,
• Linus Carlé,
• Ines Galm,
• Natalia Cañas,
• Brigitta Pascucci and
• K. Andreas Friedrich

Beilstein J. Nanotechnol. 2013, 4, 611–624, doi:10.3762/bjnano.4.68

• Center, Stuttgart, Germany 10.3762/bjnano.4.68 Abstract In this work, material-sensitive atomic force microscopy (AFM) techniques were used to analyse the cathodes of lithium–sulfur batteries. A comparison of their nanoscale electrical, electrochemical, and morphological properties was performed with

• particles. Based on the analytical findings, the first results of an optimized cathode showed a much improved discharge capacity of 800 mA·g(sulfur)−1 after 43 cycles. Keywords: conductive AFM; high capacity; lithium-sulfur batteries; material-sensitive AFM; sulfur cathode; Introduction Lithium

• rechargeable batteries with high capacity are a key technology for the widespread implementation of battery-powered cars. The specific energy of existing lithium batteries needs further improvement to enable acceptable driving ranges of electric vehicles. Moreover, this is also important for portable

Novel composite Zr/PBI-O-PhT membranes for HT-PEFC applications

• Mikhail S. Kondratenko,
• Igor I. Ponomarev,
• Marat O. Gallyamov,
• Dmitry Y. Razorenov,
• Yulia A. Volkova,
• Elena P. Kharitonova and
• Alexei R. Khokhlov

Beilstein J. Nanotechnol. 2013, 4, 481–492, doi:10.3762/bjnano.4.57

• impregnated into PBI matrices for a higher durability [7][8]. In order to improve the conductivity, proton conductors such as heteropolyacids (H3SiW12O40 (SiWA) [9][10][11][12], H3PW12O40 (PWA) [12], Cs2.5H0.5PMo12O40 (CsPMoA) [13]), lithium hydraziniumsulfate, LiN2H5SO4, (LiHzS) [14] and Zr-containing

Functionalization of vertically aligned carbon nanotubes

• Eloise Van Hooijdonk,
• Carla Bittencourt,
• Rony Snyders and
• Jean-François Colomer

Beilstein J. Nanotechnol. 2013, 4, 129–152, doi:10.3762/bjnano.4.14

• sample. The consequences were an improvement of the electrolyte penetration as well as the wettability, the capacitance, and the charge-storage properties. Rechargeable lithium-ion (Li-ion) batteries are based on the motion of lithium ions from the negative electrode to the positive electrode when being

Towards atomic resolution in sodium titanate nanotubes using near-edge X-ray-absorption fine-structure spectromicroscopy combined with multichannel multiple-scattering calculations

• Carla Bittencourt,
• Peter Krüger,
• Maureen J. Lagos,
• Xiaoxing Ke,
• Gustaaf Van Tendeloo,
• Chris Ewels,
• Polona Umek and
• Peter Guttmann

Beilstein J. Nanotechnol. 2012, 3, 789–797, doi:10.3762/bjnano.3.88

• that the structure of the layered titanate H2TinO2n+1 better describes the (Na,H)TiNTs [17][18]. Potential applications in lithium-ion batteries, catalyst supports, photocatalysts, and dye-synthesized solar cells have effectively resulted in an increasing interest in titanate nanostuctures [19][20][21

A facile approach to nanoarchitectured three-dimensional graphene-based Li–Mn–O composite as high-power cathodes for Li-ion batteries

• Wenyu Zhang,
• Yi Zeng,
• Chen Xu,
• Ni Xiao,
• Yiben Gao,
• Lain-Jong Li,
• Xiaodong Chen,
• Huey Hoon Hng and
• Qingyu Yan

Beilstein J. Nanotechnol. 2012, 3, 513–523, doi:10.3762/bjnano.3.59

• .3.59 Abstract We report a facile method to prepare a nanoarchitectured lithium manganate/graphene (LMO/G) hybrid as a positive electrode for Li-ion batteries. The Mn2O3/graphene hybrid is synthesized by exfoliation of graphene sheets and deposition of Mn2O3 in a one-step electrochemical process, which

• can help to reduce the dissolution of Mn2+ into the electrolyte, as indicated by the inductively coupled plasma (ICP) measurements, and which is mainly attributed to the large specific surface area of the graphene sheets. Keywords: cathode; graphene; Li-ion battery; lithium manganate; Introduction

• Lithium-ion batteries (LIBs) are considered the primary candidate as the power source for plug-in and hybrid electric vehicles [1]. Although LiCoO2 is widely used as a commercial cathode for Li-ion batteries, there are several drawbacks, including high cost and toxicity. Spinel Lithium Manganate (LMO) is

Reduced electron recombination of dye-sensitized solar cells based on TiO₂ spheres consisting of ultrathin nanosheets with [001] facet exposed

• Hongxia Wang,
• Meinan Liu,
• Cheng Yan and
• John Bell

Beilstein J. Nanotechnol. 2012, 3, 378–387, doi:10.3762/bjnano.3.44

• applications such as water splitting and lithium-ion batteries [6][7][8]. Further investigation shows that the [001] surface is more beneficial to the photooxidization process through the O− centers compared to the [101] surface, which contains more Ti3+ centers [9]. The different surface properties of the

Template-assisted formation of microsized nanocrystalline CeO₂ tubes and their catalytic performance in the carboxylation of methanol

• Jörg J. Schneider,
• Meike Naumann,
• Christian Schäfer,
• Armin Brandner,
• Heiko J. Hofmann and
• Peter Claus

Beilstein J. Nanotechnol. 2011, 2, 776–784, doi:10.3762/bjnano.2.86

• diesel fuel (for particle emission decrease), and also a solvent [6][25][26][27]. Owing to its low toxicity, versatile reactivity and high dielectric constant, DMC also attracts interest as an electrolyte in lithium-ion batteries [28]. The formation of DMC by direct methanol carboxylation, however, is

Highly efficient ZnO/Au Schottky barrier dye-sensitized solar cells: Role of gold nanoparticles on the charge-transfer process

• Tanujjal Bora,
• Htet H. Kyaw,
• Soumik Sarkar,
• Samir K. Pal and
• Joydeep Dutta

Beilstein J. Nanotechnol. 2011, 2, 681–690, doi:10.3762/bjnano.2.73

• counter electrode was then placed on top of the photoelectrode and a single layer of 50 μm thick surlyn 1702 (Dupont) was used as a spacer between the two electrodes. The DSSCs were then sealed and filled with the liquid electrolyte, consisting of 0.5 M lithium iodide (LiI), 0.05 M iodine (I2) and 0.5 M 4

Investigation on structural, thermal, optical and sensing properties of meta-stable hexagonal MoO₃ nanocrystals of one dimensional structure

• Angamuthuraj Chithambararaj and
• Arumugam Chandra Bose

Beilstein J. Nanotechnol. 2011, 2, 585–592, doi:10.3762/bjnano.2.62

• reactive catalysts, high optical contrast electrochromic devices and cathodic electrodes for lithium batteries, due to their unique structural, optical and electrical properties [2][3][4][5]. Several synthetic techniques have been developed for controlled synthesis of nanocrystalline MoO3 materials [6][7

Synthesis of LiNbO₃ nanoparticles in a mesoporous matrix

• Anett Grigas and
• Stefan Kaskel

Beilstein J. Nanotechnol. 2011, 2, 28–33, doi:10.3762/bjnano.2.3

• ). The obtained nanoparticles are spherical with a diameter of approximately 10 nm. Keywords: LiNbO3; ordered mesoporous material; SBA-15; template synthesis; Introduction Lithium niobate is one of the most important ferroelectric materials. At room temperature it has a rhombohedral symmetry and space

• analyses to determine the content of lithium, and niobium were carried out with an ICP-OES Vista (Varian). The samples were digested in hydrofluoric acid with microwave heating at 180 °C for 20 min. The oxygen content was determined with a TCH-600 (Leco) using the carrier gas hot extraction technique. TEM