Stereodiscrimination of guests in chiral organosilica aerogels studied by ESR spectroscopy

• Sebastian Polarz,
• Yasar Krysiak,
• Martin Wessig and
• Florian Kuhlmann

Beilstein J. Nanotechnol. 2025, 16, 2034–2054, doi:10.3762/bjnano.16.140

• were prepared accordingly [50]. For similar hydrolysis and condensation kinetics compared to the organosilane sol–gel precursors (see below), tetraisopropoxysilane (Si(OiPr)4) was used as a sol–gel precursor. After solvent exchange of the wet gel, supercritical drying with carbon dioxide delivered the

• physisorption measurements. NHxSIL was prepared by co-condensation of tetraalkyloxysilanes (e.g., Si(OMe)4) with a second sol–gel precursor such as aminopropyltriethoxysilane (APTMS, (MeO)3SiPrNH2). One can control the amine content, x, by adjusting the ratio of the two precursors in the precursor sol. A

• prepare chiral oSILs by co-condensation of Si(OiPr)4 with a sol–gel precursor that already contains the amino acid. An example is an Ala-modified 1,3-bis(triisopropoxysilyl)aniline [45][49] as shown in Scheme 1. The resulting material was characterized by scanning electron microscopy (SEM; Figure 2a); it

Nanotechnology-based approaches for the removal of microplastics from wastewater: a comprehensive review

• Nayanathara O Sanjeev,
• Manjunath Singanodi Vallabha and
• Rebekah Rubidha Lisha Rabi

Beilstein J. Nanotechnol. 2025, 16, 1607–1632, doi:10.3762/bjnano.16.114

• various techniques for synthesis of nanoparticles. Nanoparticle synthesis is essential for tailoring materials that effectively remove MPs. Various approaches allow researchers to customize structure and functionality based on application needs. For example, the sol–gel process transforms a colloidal

Photocatalytic degradation of ofloxacin in water assisted by TiO₂ nanowires on carbon cloth: contributions of H₂O₂ addition and substrate absorbability

• Iram Hussain,
• Lisha Zhang,
• Zhizhen Ye and
• Jin-Ming Wu

Beilstein J. Nanotechnol. 2025, 16, 1567–1579, doi:10.3762/bjnano.16.111

• mitigates the aggregation issues and simplifies the separation and recovery of photocatalysts within a slurry system. TiO2 nanowires are known for their significantly high surface area and are important for photocatalytic and photoelectrochemical applications. Template-mediated methods such as sol–gel

Enhancing the therapeutical potential of metalloantibiotics using nano-based delivery systems

• Alejandro Llamedo,
• Marina Cano,
• Raquel G. Soengas and
• Francisco J. García-Alonso

Beilstein J. Nanotechnol. 2025, 16, 1350–1366, doi:10.3762/bjnano.16.98

• advanced topical antibacterial treatments [120]. Different nanosystems have been explored to enhance the effectiveness of zinc complexes, including their incorporation into silica NPs. In this context, the Zn(II)–Schiff base complex 15 (Figure 4) was encapsulated in sol–gel-derived silica nanoparticles

Structural and magnetic properties of microwave-synthesized reduced graphene oxide/VO₂/Fe₂O₃ nanocomposite

• Sumanta Sahoo,
• Ankur Sood and
• Sung Soo Han

Beilstein J. Nanotechnol. 2025, 16, 921–932, doi:10.3762/bjnano.16.70

• ternary NCs of graphene materials, several conventional approaches, such as sol–gel, hydrothermal/solvothermal, calcination/thermal annealing, chemical vapor deposition, liquid-phase exfoliation, and freeze-drying have been reported. However, the MW-assisted synthetic approaches are found to be superior

• phase change of this metal oxide is generally implemented through a few approaches, including annealing, sol–gel process, hydrothermal process, vapor transport method. However, such approaches are time consuming [26][27][28]. In this context, the ultrafast reduction of V2O5 to VO2 through the MW route

Ar⁺ implantation-induced tailoring of RF-sputtered ZnO films: structural, morphological, and optical properties

• Manu Bura,
• Divya Gupta,
• Arun Kumar and
• Sanjeev Aggarwal

Beilstein J. Nanotechnol. 2025, 16, 872–886, doi:10.3762/bjnano.16.66

• displays [5], solar cells [6], and light-emitting diodes [7]. There are numerous methods for synthesizing ZnO films, including pulsed laser deposition, spray pyrolysis, radio frequency (RF) sputtering, and sol–gel techniques. Here RF sputtering is preferred over other methods because it provides high

Morphology and properties of pyrite nanoparticles obtained by pulsed laser ablation in liquid and thin films for photodetection

• Akshana Parameswaran Sreekala,
• Bindu Krishnan,
• Rene Fabian Cienfuegos Pelaes,
• David Avellaneda Avellaneda,
• Josué Amílcar Aguilar-Martínez and
• Sadasivan Shaji

Beilstein J. Nanotechnol. 2025, 16, 785–805, doi:10.3762/bjnano.16.60

• ][27][28]. In previous reports on pyrite thin films produced by EPD, Duan et al. deposited pyrite powder created using the sol–gel hydrothermal technique onto ITO substrates [29]. There are no other reports on the deposition of pyrite films using electrophoretic deposition. Spin coating is another thin

Retrieval of B1 phase from high-pressure B2 phase for CdO nanoparticles by electronic excitations in Cd_xZn_1−xO composite thin films

• Arkaprava Das,
• Marcin Zając and
• Carla Bittencourt

Beilstein J. Nanotechnol. 2025, 16, 551–560, doi:10.3762/bjnano.16.43

• Abstract This study investigates the recovery of the B1 phase from the high-pressure B2 phase, at atmospheric pressure, in cadmium oxide (CdO) nanoparticles incorporated within sol–gel synthesized CdxZn1−xO (x = 0.40) composite thin films. The recovery process is investigated using electronic excitations

• with 40% cadmium concentration in zinc oxide (ZnO) were synthesized using the sol–gel chemical route method, as detailed in our previous publication [1]. The irradiation experiments were performed using the 15 UD tandem Pelletron accelerators at the Inter-University Accelerator Centre (IUAC), New Delhi

Emerging strategies in the sustainable removal of antibiotics using semiconductor-based photocatalysts

• Yunus Ahmed,
• Keya Rani Dutta,
• Parul Akhtar,
• Md. Arif Hossen,
• Md. Jahangir Alam,
• Obaid A. Alharbi,
• Hamad AlMohamadi and
• Abdul Wahab Mohammad

Beilstein J. Nanotechnol. 2025, 16, 264–285, doi:10.3762/bjnano.16.21

• advanced methods, including sol–gel, hydrothermal, solvothermal, precipitation and template-assisted techniques [53]. The synthesis method chosen often depends on factors such as the desired crystal structure, particle size, surface area, and photocatalytic activity required for the specific application

Recent advances in photothermal nanomaterials for ophthalmic applications

• Jiayuan Zhuang,
• Linhui Jia,
• Chenghao Li,
• Rui Yang,
• Jiapeng Wang,
• Wen-an Wang,
• Heng Zhou and
• Xiangxia Luo

Beilstein J. Nanotechnol. 2025, 16, 195–215, doi:10.3762/bjnano.16.16

• effectively absorb NIR radiation and convert it into heat, thus activating the hydrogel to generate sol–gel transformation, and achieving on-demand drug release. Drugs such as timolol maleate and levofloxacin were encapsulated within separate layers of the hydrogel, facilitating a sustained, stepwise release

TiO₂ immobilized on 2D mordenite: effect of hydrolysis conditions on structural, textural, and optical characteristics of the nanocomposites

• Marina G. Shelyapina,
• Rosario Isidro Yocupicio-Gaxiola,
• Gleb A. Valkovsky and
• Vitalii Petranovskii

Beilstein J. Nanotechnol. 2025, 16, 128–140, doi:10.3762/bjnano.16.12

• starting products in a large number of reactions. The hydrolysis of various metal alkoxides by pure water, or its mixtures with primarily alcohols or other solvents, are the basis of the sol–gel method to obtain oxide materials. The tendency of metal alkoxides to this reaction can be considered as their

• most important chemical property. For various reasons, the sol–gel method is mainly associated with the hydrolysis of Si(OR)4; this reagent is readily available, inexpensive, and its hydrolysis proceeds relatively smoothly, as discussed in numerous original papers and reviews [29]. However, the

• on the ratio between TiO2 and zeolite [47][48]. Alvarez et al. [47] reported that for TiO2 deposited on mordenite during the TiO2 sol–gel synthesis in a ratio of 75:25, which is close to that in our work (i.e., between 50:50 and 70:30), leads to a noticeable increase in the bandgap (3.47 eV) [47]. It

Comparison of organic and inorganic hole transport layers in double perovskite material-based solar cell

• Deepika K and
• Arjun Singh

Beilstein J. Nanotechnol. 2025, 16, 119–127, doi:10.3762/bjnano.16.11

• are given in Table 1. Experimental Verification In 2024, a lead-free DPSC was both designed and fabricated. The included LNMO material was synthesized using the sol–gel method. The experimental and simulated J–V curves showed PCEs of 4.5 % and 10%, respectively. For the simulation, TiO2 was used as

Orientation-dependent photonic bandgaps in gold-dust weevil scales and their titania bioreplicates

• Norma Salvadores Farran,
• Limin Wang,
• Primoz Pirih and
• Bodo D. Wilts

Beilstein J. Nanotechnol. 2025, 16, 1–10, doi:10.3762/bjnano.16.1

• }-oriented domains exhibits polarization conversion, rotating the angle of linearly polarized light. The overall coloration, resulting from the reflections from many scales, is close to uniformly diffuse because of the random orientation of the domains. Using titania sol–gel chemistry, we produced negative

• of 1.55 to 2.00. The study suggests that the effective refractive index of titania in the 3D lattice is similar to that in sol–gel films. The study demonstrates the potential of replicating complex biophotonic structures using the sol–gel technique. Optimization of the sol–gel process could lead to

• customizable photonic bandgaps that might be used in novel optical materials. Keywords: animal coloration; photonic crystal; polarization conversion; sol–gel replication; weevil; Introduction Animal coloration is produced by means of absorption, scattering, luminescence, and interference. The latter is

Fabrication of hafnium-based nanoparticles and nanostructures using picosecond laser ablation

• Abhishek Das,
• Mangababu Akkanaboina,
• Jagannath Rathod,
• R. Sai Prasad Goud,
• Kanaka Ravi Kumar,
• Raghu C. Reddy,
• Ratheesh Ravendran,
• Katia Vutova,
• S. V. S. Nageswara Rao and
• Venugopal Rao Soma

Beilstein J. Nanotechnol. 2024, 15, 1639–1653, doi:10.3762/bjnano.15.129

• desired morphology is essential for a given application. Generally, practical techniques for obtaining nanomaterials are sol–gel method, chemical and physical vapour deposition, hydrothermal method, ball milling, grinding, lithography, etching, and laser ablation [14][15][16][17][18]. The morphology

Mn-doped ZnO nanopowders prepared by sol–gel and microwave-assisted sol–gel methods and their photocatalytic properties

• Cristina Maria Vlăduț,
• Crina Anastasescu,
• Silviu Preda,
• Oana Catalina Mocioiu,
• Simona Petrescu,
• Jeanina Pandele-Cusu,
• Dana Culita,
• Veronica Bratan,
• Ioan Balint and
• Maria Zaharescu

Beilstein J. Nanotechnol. 2024, 15, 1283–1296, doi:10.3762/bjnano.15.104

• 10.3762/bjnano.15.104 Abstract Although the microwave-assisted sol–gel method is quite frequently used for the preparation of oxide nanostructures, the synergism of the reaction pathways is not fully explained. However, state-of-the-art theoretical and practical results of high novelty can be achieved by

• continuously evaluating the as-synthesized materials. The present paper presents a comparative study of Mn-doped ZnO nanopowders prepared by both sol–gel and microwave-assisted sol–gel methods. The structural, morphological, and optical properties of the as-obtained powders were established and correlated with

• preferred for synthesizing oxide nanostructures because of their advantages, such as uniform mixing of precursors at the molecular level, low operating temperatures, and the ability to control the physicochemical properties of the final products [5][6]. Among various chemical techniques, the sol–gel method

Interface properties of nanostructured carbon-coated biological implants: an overview

• Mattia Bartoli,
• Francesca Cardano,
• Erik Piatti,
• Stefania Lettieri,
• Andrea Fin and
• Alberto Tagliaferro

Beilstein J. Nanotechnol. 2024, 15, 1041–1053, doi:10.3762/bjnano.15.85

• PVD, CVD, and sol–gel deposition of NDs on ceramics, together with excellent adhesion of the protective layer [143][144]. Chernysheva et al. [145][146] investigated the production of protective ND layers onto a xenogenic heart valve, evaluating the role of the ND surface potential. A negative surface

Effect of repeating hydrothermal growth processes and rapid thermal annealing on CuO thin film properties

• Monika Ozga,
• Eunika Zielony,
• Aleksandra Wierzbicka,
• Anna Wolska,
• Marcin Klepka,
• Marek Godlewski,
• Bogdan J. Kowalski and
• Bartłomiej S. Witkowski

Beilstein J. Nanotechnol. 2024, 15, 743–754, doi:10.3762/bjnano.15.62

• thin films can also be grown from liquid phases, employing techniques such as chemical bath deposition [31][32][33], successive ionic layer adsorption and reaction (SILAR) [34][35][36], sol–gel processes (using dip and spin coating) [37][38][39], as well as spray pyrolysis [40][41][42]. This work

Simultaneous electrochemical determination of uric acid and hypoxanthine at a TiO₂/graphene quantum dot-modified electrode

• Vu Ngoc Hoang,
• Dang Thi Ngoc Hoa,
• Nguyen Quang Man,
• Le Vu Truong Son,
• Le Van Thanh Son,
• Vo Thang Nguyen,
• Le Thi Hong Phong,
• Ly Hoang Diem,
• Kieu Chan Ly,
• Ho Sy Thang and
• Dinh Quang Khieu

Beilstein J. Nanotechnol. 2024, 15, 719–732, doi:10.3762/bjnano.15.60

• lithium-ion storage performance of C-GQDs/α-Fe2O3 composites in lithium batteries presented excellent cyclability and rate capability [19]. Among several chemical approaches for the synthesis of titania, sol–gel processes have been commonly used for practical application. In these sol–gel methods

Modification of graphene oxide and its effect on properties of natural rubber/graphene oxide nanocomposites

• Nghiem Thi Thuong,
• Le Dinh Quang,
• Vu Quoc Cuong,
• Cao Hong Ha,
• Nguyen Ba Lam and
• Seiichi Kawahara

Beilstein J. Nanotechnol. 2024, 15, 168–179, doi:10.3762/bjnano.15.16

• after drying the solution in a heating oven. Vinyltriethoxysilane was used to modify GO [25][32] and it was bonded on the GO surface by the sol–gel method, as shown in Figure 1. Firstly, GO (0.4 g) was thoroughly dispersed in distilled water. After that, VTES (1.8 g) was added to the mixture, followed

A visible-light photodetector based on heterojunctions between CuO nanoparticles and ZnO nanorods

• Doan Nhat Giang,
• Nhat Minh Nguyen,
• Duc Anh Ngo,
• Thanh Trang Tran,
• Le Thai Duy,
• Cong Khanh Tran,
• Thi Thanh Van Tran,
• Phan Phuong Ha La and
• Vinh Quang Dang

Beilstein J. Nanotechnol. 2023, 14, 1018–1027, doi:10.3762/bjnano.14.84

• ) solution in an oven at 95 °C within 3 h (as presented in Supporting Information File 1, Figure S1). CuO NPs were synthesized via a simple and low-cost sol–gel method. At first, a mixture of 1.21 g Cu(NO3)2·5H2O and 0.8 g NaOH was dissolved in 50 mL deionized water under constant stirring at room

Upscaling the urea method synthesis of CoAl layered double hydroxides

• Camilo Jaramillo-Hernández,
• Víctor Oestreicher,
• Martín Mizrahi and
• Gonzalo Abellán

Beilstein J. Nanotechnol. 2023, 14, 927–938, doi:10.3762/bjnano.14.76

• ], sol–gel methods [26], mechanochemistry [27], or the epoxide route [28], to name a few [29]. Among them, hydrothermal methods based on ammonium-releasing reagents (ARRs), commonly urea or hexamethylenetetramine, are especially interesting since they allow one to obtain large and highly crystalline

Nanoarchitectonics to entrap living cells in silica-based systems: encapsulations with yolk–shell and sepiolite nanomaterials

• Celia Martín-Morales,
• Jorge Fernández-Méndez,
• Pilar Aranda and
• Eduardo Ruiz-Hitzky

Beilstein J. Nanotechnol. 2023, 14, 522–534, doi:10.3762/bjnano.14.43

• sol–gel methods, as well as pre-synthesised yolk–shell bionanohybrids have been studied subsequently. Optical microscopy and SEM confirm that the silica shell microstructures provide a reduced contact between cells. The inorganic matrix increases the survival of the cells and maintains their

• , by inorganic components generated by sol–gel processes from silicon alkoxides is an illustrative example of biohybrids that display the extraordinary functionality inherent to the assembled living components. For instance, bacteria such as Escherichia coli maintain their metabolic activity entrapped

• precursor could be cast and gelled as thin films or hollow tubular monoliths with thin walls, improving the interaction between the encapsulated cells and a liquid medium in which the material could be placed. In addition to the optimisation of the sol–gel synthesis, the conditions for yolk–shell

Bismuth-based nanostructured photocatalysts for the remediation of antibiotics and organic dyes

• Akeem Adeyemi Oladipo and
• Faisal Suleiman Mustafa

Beilstein J. Nanotechnol. 2023, 14, 291–321, doi:10.3762/bjnano.14.26

• techniques have been developed to synthesise 3-D Bi-based nanostructures with different morphologies, including solvothermal/hydrothermal and sol–gel processes, mechanical exfoliation, solid-state reactions, chemical vapour deposition, and microwave-assisted techniques [106]. These 3-D photocatalysts have

• . The final product might have some impurities, relatively large particles, and only a small degree of homogeneity. Large volumes of nanopowder can be produced using a relatively simple apparatus via solid-state routes. Wet-chemical methods (such as electrospinning, sol–gel, hydrothermal, ultrasound, co

• pure Bi2WO6 (82.8%), the dopant significantly increased the tetracycline-degrading activity, which reached 94.6% within 1 h of visible light irradiation. Additionally, Irfan et al. [148] used a bi-solvent sol–gel technique to synthesise porous bismuth ferrite nanostructures with various morphological

Antimicrobial and mechanical properties of functionalized textile by nanoarchitectured photoinduced Ag@polymer coating

• Jessica Plé,
• Marine Dabert,
• Helene Lecoq,
• Sophie Hellé,
• Lydie Ploux and
• Lavinia Balan

Beilstein J. Nanotechnol. 2023, 14, 95–109, doi:10.3762/bjnano.14.11

• difficult to implement and tend to cause NP self-aggregation. In situ methods are therefore generally preferred and typically require the polymer film surface to be treated with a metal precursor solution (layer-by-layer [37][38], sol–gel [39]) before undergoing thermal [40] or chemical reduction reactions

A TiO₂@MWCNTs nanocomposite photoanode for solar-driven water splitting

• Anh Quynh Huu Le,
• Ngoc Nhu Thi Nguyen,
• Hai Duy Tran,
• Van-Huy Nguyen and
• Le-Hai Tran

Beilstein J. Nanotechnol. 2022, 13, 1520–1530, doi:10.3762/bjnano.13.125

• ) nanocomposite by sol–gel method for visible-light-induced photocatalytic hydrogen evolution [8]. The photocatalyst consisted of dense TiO2 particles covering functionalized MWNTs and exhibited good photoactivity under visible light (λ > 420 nm), but the photoelectrochemical water splitting showed a low hydrogen

• nanocomposites as photoanode material for photoelectrochemical water splitting. Furthermore, the preparation of TiO2/MWCNTs nanocomposite derived from TiO2 precursors and functionalized MWCMTs for photoelectrochemical water splitting is based on complicated and time-consuming hydrothermal and sol–gel methods

• , in which the TiO2 particles are uniformly attached to CNTs by layer-by-layer coating or sol–gel methods [15][16][17]. Notably, the defects on the wall surface of MWCNTs, which enable π–π interactions, could be the active sites to generate the TiO2 agglomerations via hydroxy groups and, thus, enhance