He⁺ FIBID-fabricated 3D AFM tip architectures: an exploratory study of hollow pillars, helices, and spirals

• Alba Arroyo-Fructuoso,
• Ana Galet,
• Gregor Hlawacek and
• Rosa Córdoba

Beilstein J. Nanotechnol. 2026, 17, 863–871, doi:10.3762/bjnano.17.62

• required. Keywords: 3D-printed tips; AFM tips; beam induced nanomanufacturing; focused ion beam induced deposition (FIBID); helium ion microscope; nanohelix; nanopillar; nanospiral; scanning tip microscopy; surface topography; tungsten carbide; Introduction The atomic force microscope (AFM) is a

Selected properties of Al_xZn_yO thin films prepared by reactive pulsed magnetron sputtering using a two-element Zn/Al target

• Witold Posadowski,
• Artur Wiatrowski,
• Jarosław Domaradzki and
• Michał Mazur

Beilstein J. Nanotechnol. 2022, 13, 344–354, doi:10.3762/bjnano.13.29

• Table 1. The sheet resistance of the deposited thin films was determined using a standard four-point probe head (Jandel Engineering Ltd.) and a source-measure unit (Keithley 2611A type). The measuring head was equipped with four tungsten carbide needles, which were arranged in line with a needle-to

Self-standing heterostructured NiC_x-NiFe-NC/biochar as a highly efficient cathode for lithium–oxygen batteries

• Shengyu Jing,
• Xu Gong,
• Shan Ji,
• Linhui Jia,
• Bruno G. Pollet,
• Sheng Yan and
• Huagen Liang

Beilstein J. Nanotechnol. 2020, 11, 1809–1821, doi:10.3762/bjnano.11.163

• [26]. For instance, molybdenum/tungsten carbide with a well-defined nanostructure was synthesized via a hydrothermal method, and the obtained metal carbide catalyst yielded a high capacity in lithium–oxygen batteries [15]. Also, titanium carbide was synthesized by Bruce et al. as cathode material for

3D superconducting hollow nanowires with tailored diameters grown by focused He⁺ beam direct writing

• Rosa Córdoba,
• Alfonso Ibarra,
• Dominique Mailly,
• Isabel Guillamón,
• Hermann Suderow and
• José María De Teresa

Beilstein J. Nanotechnol. 2020, 11, 1198–1206, doi:10.3762/bjnano.11.104

• tungsten carbide nanowires with tailored diameters by tuning two key growth parameters, namely current and dose of the ion beam. Our results show the control of geometry in 3D hollow nanowires, with outer and inner diameters ranging from 36 to 142 nm and from 5 to 28 nm, respectively; and lengths from 0.5

• nano-antennas and sensors, based on 3D superconducting architectures. Keywords: electron tomography; focused ion beam induced deposition (FIBID); helium ion microscope; magneto-transport measurements; nano-superconductors; tungsten carbide (WC); Introduction Superconductors are dissipationless

Dry friction of microstructured polymer surfaces inspired by snake skin

• Martina J. Baum,
• Lars Heepe,
• Elena Fadeeva and
• Stanislav N. Gorb

Beilstein J. Nanotechnol. 2014, 5, 1091–1103, doi:10.3762/bjnano.5.122

• way to modulate friction. They used groove-textured surfaces and performed frictional measurement on two different combinations of sphere and microstructure dimension. For the combination of a tungsten carbide sphere (diameter = 800 µm) and a microstructured silica surface (λ = 278 nm) the frictional

• coefficient parallel to the microstructure was higher, than in the perpendicular direction. The second investigated frictional pair was a steel ball (diameter = 800 µm) in contact with a microstructured tungsten carbide surface (λ = 220 µm). For this combination, the frictional coefficients in both directions

Influence of particle size and fluorination ratio of CF_x precursor compounds on the electrochemical performance of C–FeF₂ nanocomposites for reversible lithium storage

• Ben Breitung,
• M. Anji Reddy,
• Venkata Sai Kiran Chakravadhanula,
• Michael Engel,
• Christian Kübel,
• Annie K. Powell,
• Horst Hahn and
• Maximilian Fichtner

Beilstein J. Nanotechnol. 2013, 4, 705–713, doi:10.3762/bjnano.4.80

• precursor was performed in a sealed tungsten carbide vial under inert conditions. The CFx powder was ball-milled for 2 h, with a ball to powder ratio of 24:1 and milling speeds of 200, 300, and 400 rpm. To adjust the active material to carbon ratio in the products, different graphite fluoride samples were