3D solid supported inter-polyelectrolyte complexes obtained by the alternate deposition of poly(diallyldimethylammonium chloride) and poly(sodium 4-styrenesulfonate)

• Eduardo Guzmán,
• Armando Maestro,
• Sara Llamas,
• Jesús Álvarez-Rodríguez,
• Francisco Ortega,
• Ángel Maroto-Valiente and
• Ramón G. Rubio

Beilstein J. Nanotechnol. 2016, 7, 197–208, doi:10.3762/bjnano.7.18

• layers obtained by the layer-by-layer method. A multimodal characterization showed the absence of stratification of the films formed by the alternate deposition of poly(diallyldimethylammonium chloride) and poly(sodium 4-styrenesulfonate). Indeed the final organization might be regarded as three

• -micrometric scale, has become necessary [1][2][3]. Among these techniques, the layer-by-layer (LbL) self-assembly has become probably one of the most promising [4][5], due to its high versatility and low costs [6][7]. Furthermore, a very broad range of compounds can be assembled through LbL: synthetic

• purification. The ionic strength of the solutions was controlled by adding NaCl (Sigma-Aldrich, purity > 99.9%). The water used for all the experiments was of Milli-Q quality (Millipore RG model). All the experiments were done at (298.1 ± 1.0) K. Layer-by-layer assembly In a similar manner as described in [8

Fabrication and characterization of novel multilayered structures by stereocomplexion of poly(D-lactic acid)/poly(L-lactic acid) and self-assembly of polyelectrolytes

• Elena Dellacasa,
• Li Zhao,
• Gesheng Yang,
• Laura Pastorino and
• Gleb B. Sukhorukov

Beilstein J. Nanotechnol. 2016, 7, 81–90, doi:10.3762/bjnano.7.10

• ) (PLLA) were alternately adsorbed directly on calcium carbonate (CaCO3) templates and on poly(styrene sulfonate) (PSS) and poly(allylamine hydrochloride) (PAH) multilayer precursors in order to fabricate a novel layer-by-layer (LBL) assembly. A single layer of poly(L-lysine) (PLL) was used as a linker

• for sustained release. Keywords: biocompatibility; layer-by-layer assembly; microcapsules; poly(lactic acids); stereocomplex; Introduction The polycationic/polyanionic layer-by-layer (LBL) deposition on surfaces has been widely studied since the first description by Decher et al. [1][2][3]. The

Controlled graphene oxide assembly on silver nanocube monolayers for SERS detection: dependence on nanocube packing procedure

• Martina Banchelli,
• Bruno Tiribilli,
• Roberto Pini,
• Luigi Dei,
• Paolo Matteini and
• Gabriella Caminati

Beilstein J. Nanotechnol. 2016, 7, 9–21, doi:10.3762/bjnano.7.2

• , electrostatic layer-by-layer adsorption and formation of nanoparticle films at the liquid−liquid interface [23][24][25][26]. In the latter case, assembly of uncapped nanoparticles generally leads to the formation of loosely packed aggregates and linking functionalities must be employed to decrease the

• derivatives and nanoparticles including metal evaporation, electrochemical deposition and layer-by-layer self-assembly techniques [51]. Zarbin's group [20] directly synthesized and assembled silver nanoparticle/graphene oxide nanocomposites at a water/toluene liquid–liquid interface whereas Wang et al. [52

pH-Triggered release from surface-modified poly(lactic-co-glycolic acid) nanoparticles

• Manuel Häuser,
• Klaus Langer and
• Monika Schönhoff

Beilstein J. Nanotechnol. 2015, 6, 2504–2512, doi:10.3762/bjnano.6.260

• nanoparticles are coated by polyelectrolytes using the layer-by-layer self-assembly technique, employing poly(acrylic acid) (PAA) as a pH-sensitive component and poly(diallyldimethylammonium chloride) (PDADMAC) as the releasable polycation. The pH during multilayer deposition plays a major role and influences

• the nanoparticles with high concentrations of sodium chloride shows no further release and thus demonstrates the pH-driven release to be quantitative. Keywords: layer-by-layer self-assembly; pH-triggered release; PLGA nanoparticles; polyelectrolyte multilayers; weak polyelectrolyte; Introduction The

• established these days, such as covalent ligand binding via crosslinking agents [12][13] and different adsorption strategies [14]. The layer-by-layer (LbL) self-assembly technique, introduced by Decher and Hong in the early 1990s [15] has proven to be an outstandingly valuable method for the fabrication of

Fabrication of hybrid graphene oxide/polyelectrolyte capsules by means of layer-by-layer assembly on erythrocyte cell templates

• Joseba Irigoyen,
• Nikolaos Politakos,
• Eleftheria Diamanti,
• Elena Rojas,
• Marco Marradi,
• Raquel Ledezma,
• Layza Arizmendi,
• J. Alberto Rodríguez,
• Ronald F. Ziolo and
• Sergio E. Moya

Beilstein J. Nanotechnol. 2015, 6, 2310–2318, doi:10.3762/bjnano.6.237

• capsules are easily produced through the layer-by-layer technique using alternating polyelectrolyte layers and GO sheets. The amount of GO and therefore its coverage in the resulting capsules can be tuned by adjusting the concentration of the GO dispersion during the assembly. The capsules retain the

• FTIR spectroscopies. Keywords: capsules; erythrocytes; graphene; layer by layer; polyelectrolyte membranes; Introduction The past decades have witnessed explosive growth in research on low-dimensional carbon forms with graphene and carbon nanotubes in the forefront [1][2][3]. The unique electrical

• layer-by-layer technique (LbL). Although the technique was originally developed for the alternating assembly of polyelectrolytes (PE) of opposite charge, LbL can be and has been extended to include particles, 2D layered materials, nanostructures, and lipid vesicles, which provide charged surfaces, or

Fabrication of hybrid nanocomposite scaffolds by incorporating ligand-free hydroxyapatite nanoparticles into biodegradable polymer scaffolds and release studies

• Balazs Farkas,
• Marina Rodio,
• Ilaria Romano,
• Alberto Diaspro,
• Romuald Intartaglia and
• Szabolcs Beke

Beilstein J. Nanotechnol. 2015, 6, 2217–2223, doi:10.3762/bjnano.6.227

• on a layer-by-layer building-up process where one layer is fabricated by image projection using pulsed excimer laser radiation. The method is explained in detail in [22]. Briefly, the method goes as follows: the output beam of a XeCl excimer laser (at 308 nm wavelength) is coupled to a customized

Optimized design of a nanostructured SPCE-based multipurpose biosensing platform formed by ferrocene-tethered electrochemically-deposited cauliflower-shaped gold nanoparticles

• Wicem Argoubi,
• Maroua Saadaoui,
• Sami Ben Aoun and
• Noureddine Raouafi

Beilstein J. Nanotechnol. 2015, 6, 1840–1852, doi:10.3762/bjnano.6.187

• biosensor (Figure 6a and Figure 6b). Selective detection of H2O2 The simplicity of design and the ease of layer-by-layer modification make this surface an excellent electrochemical sensing platform for hydrogen peroxide detection. Figure 6c shows typical chronoamperometric responses of the ferrocene moiety

Thermal treatment of magnetite nanoparticles

• Beata Kalska-Szostko,
• Urszula Wykowska,
• Dariusz Satula and
• Per Nordblad

Beilstein J. Nanotechnol. 2015, 6, 1385–1396, doi:10.3762/bjnano.6.143

• in aqueous ammonia solution (MNP-1). This is a low temperature reaction that was conducted at 80 °C under Ar atmosphere. The procedure was adopted from the Massart method [7][22][23]. The second (MNP-2) and third (MNP-3) type of nanoparticles were based on the layer-by-layer synthetic procedure

The Kirkendall effect and nanoscience: hollow nanospheres and nanotubes

• Abdel-Aziz El Mel,
• Ryusuke Nakamura and
• Carla Bittencourt

Beilstein J. Nanotechnol. 2015, 6, 1348–1361, doi:10.3762/bjnano.6.139

• become bigger while the bismuth core disappeared in a layer-by-layer fashion. By the end of the conversion process, a nonuniform oxide shell was formed. The authors demonstrated that this effect is related to the fact that bismuth diffuses out of the oxide shell nonuniformly with a faster diffusion rate

Growth and morphological analysis of segmented AuAg alloy nanowires created by pulsed electrodeposition in ion-track etched membranes

• Ina Schubert,
• Loic Burr,
• Christina Trautmann and
• Maria Eugenia Toimil-Molares

Beilstein J. Nanotechnol. 2015, 6, 1272–1280, doi:10.3762/bjnano.6.131

• through the nitric acid treatment. This effect is ascribed to dealloying in AuAg alloy structures taking place through layer-by-layer dissolution of Ag atoms and diffusion of Au atoms onto the surface [57][58]. Due to a higher Au concentration in the Au-rich segments, a Au passivation layer on the surface

Scanning reflection ion microscopy in a helium ion microscope

• Yuri V. Petrov and
• Oleg F. Vyvenko

Beilstein J. Nanotechnol. 2015, 6, 1125–1137, doi:10.3762/bjnano.6.114

• incidence angles, yet was still more pronounced in REM as compared to TEM [2][4]. The further development of REM in ultrahigh vacuum conditions allowed imaging of the single atomic steps [5][6][7][8] and monitoring of atomic layer-by-layer crystal growth by means of reflection high energy electron

Magnetic properties of self-organized Co dimer nanolines on Si/Ag(110)

• Lisa Michez,
• Kai Chen,
• Fabien Cheynis,
• Frédéric Leroy,
• Alain Ranguis,
• Haik Jamgotchian,
• Margrit Hanbücken and
• Laurence Masson

Beilstein J. Nanotechnol. 2015, 6, 777–784, doi:10.3762/bjnano.6.80

• has been reported that the Co nanoline growth proceeds in a nearly layer-by-layer growth, reproducing the 1D pattern of the Si template up to five monolayers thick. The width of the Co dimer nanolines is similar to the width of a single Si NR. Co adsorption on double Si NRs leads to the formation of

Self-assembled anchor layers/polysaccharide coatings on titanium surfaces: a study of functionalization and stability

• Ognen Pop-Georgievski,
• Dana Kubies,
• Josef Zemek,
• Neda Neykova,
• Roman Demianchuk,
• Eliška Mázl Chánová,
• Miroslav Šlouf,
• Milan Houska and
• František Rypáček

Beilstein J. Nanotechnol. 2015, 6, 617–631, doi:10.3762/bjnano.6.63

• ]. Chitosan/alginate, multilayered, 3D networks prepared by the layer-by-layer method enabled encapsulation of bone marrow stromal cells on the surface of dental or joint implants [18]. Polyelectrolyte (chitosan, poly(L-glutamic acid), and poly-L-lysine) coatings increased the surface ionic nature and

Silica micro/nanospheres for theranostics: from bimodal MRI and fluorescent imaging probes to cancer therapy

• Shanka Walia and
• Amitabha Acharya

Beilstein J. Nanotechnol. 2015, 6, 546–558, doi:10.3762/bjnano.6.57

• . The fluorescence emission peak at 520 (from FITC) and 573 nm (from nanocomposites) confirmed the bioconjugation of amine-functionalized hybrid nanocomposites with FITC-IgG. In a similar way, Nai-Qiang et al. [41] reported a simple modified Stöber process in combination with layer by layer assembly for

• multimodal magnetic and fluorescent silica spheres synthesized through the Stöber process and a layer-by-layer assembly approach. The incorporation of Fe3O4 NPs into the silica shell was done following the Stöber process by using TEOS/NH4OH. The layer-by-layer assembly approach was utilized for the

Exploiting the hierarchical morphology of single-walled and multi-walled carbon nanotube films for highly hydrophobic coatings

• Francesco De Nicola,
• Paola Castrucci,
• Manuela Scarselli,
• Francesca Nanni,
• Ilaria Cacciotti and
• Maurizio De Crescenzi

Beilstein J. Nanotechnol. 2015, 6, 353–360, doi:10.3762/bjnano.6.34

• former are smaller than the latter (about one order of magnitude), we observed that a surface hierarchy naturally occurs by depositing layer by layer a SWCNT film upon a MWCNT film. The particular two-fold hierarchical morphology of the surface, resembling that observed in lotus leaves [3] and rose

Oxygen-plasma-modified biomimetic nanofibrous scaffolds for enhanced compatibility of cardiovascular implants

• Anna Maria Pappa,
• Varvara Karagkiozaki,
• Silke Krol,
• Spyros Kassavetis,
• Dimitris Konstantinou,
• Charalampos Pitsalidis,
• Lazaros Tzounis,
• Nikos Pliatsikas and
• Stergios Logothetidis

Beilstein J. Nanotechnol. 2015, 6, 254–262, doi:10.3762/bjnano.6.24

• plasma-treated electrospun scaffolds are shown in Figure 1a–c. The images clearly indicate the effect of the plasma modification on the structural and surface integrity of the electrospun scaffolds. The unmodified fabricated nanofibers appeared interconnected and randomly stacked in a layer-by-layer

Synthesis of boron nitride nanotubes and their applications

• Saban Kalay,
• Zehra Yilmaz,
• Ozlem Sen,
• Melis Emanet,
• Emine Kazanc and
• Mustafa Çulha

Beilstein J. Nanotechnol. 2015, 6, 84–102, doi:10.3762/bjnano.6.9

• into the catalyst particle while the N2 is decomposed to N atoms on the surface of the catalyst. The precursors precipitate layer-by-layer to form the BNNTs [30]. In the tip-growth mechanism, the catalyst is located on the tip of growing BNNTs [59]. Thus, the BNNTs are generally formed as bamboo-like

The impact of the confinement of reactants on the metal distribution in bimetallic nanoparticles synthesized in reverse micelles

• Concha Tojo,
• Elena González and
• Nuria Vila-Romeu

Beilstein J. Nanotechnol. 2014, 5, 1966–1979, doi:10.3762/bjnano.5.206

• metallic atoms on the nucleus, that is, a growing particle is built up layer by layer. Therefore, whenever a metal atom is exchanged towards a nucleated micelle, this atom is deposited on the nucleus. The sequence of metal deposition (Au or Pt) is stored in each micelle at each step. In addition

• calculated layer by layer. This final distribution is averaged over 1000 runs. The nanoparticle structure is represented by histograms, in which the layer composition (% Au) is represented by a color grading. The distribution ranges from blue (0–10% for the fast metal Au) to red (90–100% of Au). 50% of each

Towards bottom-up nanopatterning of Prussian blue analogues

• Virgile Trannoy,
• Marco Faustini,
• David Grosso,
• Sandra Mazerat,
• François Brisset,
• Alexandre Dazzi and
• Anne Bleuzen

Beilstein J. Nanotechnol. 2014, 5, 1933–1943, doi:10.3762/bjnano.5.204

• last step is the PBA growth by a layer-by-layer directed assembly approach inspired from methods already implemented for the synthesis of PBA thin films [16][17][18]. Here, we study the impact of each step on the structure of the nanocomposite. We show that the first gold layer can undergo some changes

• -aminothiophenol are abbreviated as MHA, 4-MPy and 4-ATP, respectively, in the following. The film was rinsed with EtOH and water. Scheme 2 shows the successive functionalization steps of the film in the case of the MHA anchorage [20][21]. The last step is the PBA growth through a layer-by-layer approach

• of the smallest particles is of the order of magnitude expected for PBA particles formed by a layer-by-layer approach since 15 units of –Fe–CN–Co- (corresponding to 15 cycles) corresponds to approximately 8 nm. Therefore, a growth from Co ions anchored to the bottom of the perforations could result

Controlling the dispersion of supported polyoxometalate heterogeneous catalysts: impact of hybridization and the role of hydrophilicity–hydrophobicity balance and supramolecularity

• Gijo Raj,
• Colas Swalus,
• Eglantine Arendt,
• Pierre Eloy,
• Michel Devillers and
• Eric M. Gaigneaux

Beilstein J. Nanotechnol. 2014, 5, 1749–1759, doi:10.3762/bjnano.5.185

• hybrids are deposited. For instance, surfactant-encapsulated clusters of POM anions, formed through electrostatic interactions, were reported to form well-ordered straight nanorods on graphite [17], whereas hybrid materials formed through covalent functionalization of POM formed planar layer-by-layer

Influence of surface-modified maghemite nanoparticles on in vitro survival of human stem cells

• Michal Babič,
• Daniel Horák,
• Lyubov L. Lukash,
• Tetiana A. Ruban,
• Yurii N. Kolomiets,
• Svitlana P. Shpylova and
• Oksana A. Grypych

Beilstein J. Nanotechnol. 2014, 5, 1732–1737, doi:10.3762/bjnano.5.183

• ., dextran [18][19] (in Feridex® and Endorem® developed as contrast agents for magnetic resonance imaging, MRI), poly(ethylene glycol) (PEG) [1], poly(N,N-dimethylacrylamide) (PDMAAm) [20], poly(L-lysine) [21][22], protamine sulfate [23], or layer-by-layer polyelectrolyte complexes [24]. The aim of this

Current state of laser synthesis of metal and alloy nanoparticles as ligand-free reference materials for nano-toxicological assays

• Christoph Rehbock,
• Jurij Jakobi,
• Lisa Gamrad,
• Selina van der Meer,
• Daniela Tiedemann,
• Ulrike Taylor,
• Wilfried Kues,
• Detlef Rath and
• Stephan Barcikowski

Beilstein J. Nanotechnol. 2014, 5, 1523–1541, doi:10.3762/bjnano.5.165

• basically implies that the onset of particle fragmentation occurs at the boiling point of the material and emission of smaller particles transpires layer by layer [59][60]. The second mechanism is Coulomb explosion, which occurs when large quantities of electrons are ejected from the particle due to laser

Electron-beam induced deposition and autocatalytic decomposition of Co(CO)₃NO

• Florian Vollnhals,
• Martin Drost,
• Fan Tu,
• Esther Carrasco,
• Andreas Späth,
• Rainer H. Fink,
• Hans-Peter Steinrück and
• Hubertus Marbach

Beilstein J. Nanotechnol. 2014, 5, 1175–1185, doi:10.3762/bjnano.5.129

• and not by homogeneous layer-by-layer growth. For this complex growth process, during which the number of available sites, the (local) precursor concentration or both may vary, a nonlinear behavior is to be expected. EBISA plus autocatalytic growth The susceptibility to decomposition by an electron

Organic and inorganic–organic thin film structures by molecular layer deposition: A review

• Pia Sundberg and
• Maarit Karppinen

Beilstein J. Nanotechnol. 2014, 5, 1104–1136, doi:10.3762/bjnano.5.123

• of producing high-quality nanometer-scale thin films in an atomic layer-by-layer manner. Compared with other advanced gas-phase thin-film deposition techniques, ALD has several distinct advantages: The films can be deposited with a great control over the film thickness and they are not only pinhole

• was fundamentally broadened by experiments producing organic polymers in the 1990s by a variant of ALD, now commonly known as molecular layer deposition (MLD), named after the molecular layer-by-layer fashion the film grows during the deposition [5][6][7][8][9]. Then – most excitingly – in the late

Optical and structural characterization of oleic acid-stabilized CdTe nanocrystals for solution thin film processing

• Claudio Davet Gutiérrez-Lazos,
• Mauricio Ortega-López,
• Manuel A. Pérez-Guzmán,
• A. Mauricio Espinoza-Rivas,
• Francisco Solís-Pomar,
• Rebeca Ortega-Amaya,
• L. Gerardo Silva-Vidaurri,
• Virginia C. Castro-Peña and
• Eduardo Pérez-Tijerina

Beilstein J. Nanotechnol. 2014, 5, 881–886, doi:10.3762/bjnano.5.100

• CIS films for photovoltaic applications. Jasieniak et al. [24] deposited photovoltaic cadmium telluride (CdTe) thin films by using pyridine-capped CdTe nanocrystals. In their approach, CdTe nanocrystals were deposited from solution by a layer-by-layer process with subsequent annealing per layer at 300