A top-down approach for fabricating three-dimensional closed hollow nanostructures with permeable thin metal walls

• Carlos Angulo Barrios and
• Víctor Canalejas-Tejero

Beilstein J. Nanotechnol. 2017, 8, 1231–1237, doi:10.3762/bjnano.8.124

• as artificial cells [2], controlled transport and delivery of chemical agents (e.g., pharmaceutical drugs) [3], catalysis [4], lithium batteries [5] and confined reaction compartments (nanoreactors) [1]. Most fabrication methods of nanocages are based on bottom-up techniques, mainly colloidal and sol

Structural properties and thermal stability of cobalt- and chromium-doped α-MnO₂ nanorods

• Romana Cerc Korošec,
• Polona Umek,
• Alexandre Gloter,
• Jana Padežnik Gomilšek and
• Peter Bukovec

Beilstein J. Nanotechnol. 2017, 8, 1032–1042, doi:10.3762/bjnano.8.104

• can be used as a cathode-active material for rechargeable lithium batteries [8], an electrode material for supercapacitors [9][10], and shows excellent catalytic activity for the selective oxidation of benzyl alcohols [11][12]. The catalytic properties are related to the redox cycling of various

• Co2+ have been published. It seems that doping with cobalt allows for the preparation of materials with enhanced characteristics. In an attempt to modify α-MnO2 as cathode for high energy density lithium batteries, nanostructured MnO2, doped with 2 atom % Co, was synthesized [20]. In Co-doped

• dopant so drastically affects the physical properties of the MnO2 matrix. Because of economic reasons MnO2 is one of the most attractive cathodes for rechargable lithium batteries. Since Mn is the tenth-most abundant element in the Earth crust, lithiated MnO2 cathodes would cost around 1% of LiCoO2, the

Vapor deposition routes to conformal polymer thin films

• Priya Moni,
• Ahmed Al-Obeidi and
• Karen K. Gleason

Beilstein J. Nanotechnol. 2017, 8, 723–735, doi:10.3762/bjnano.8.76

• times the Young’s Modulus of a bare CNT sheet [40]. Emerging applications for ultrathin polymer films on nanostructured high aspect ratio structures include various energy storage devices and soft electronics. For instance, silicon based anodes are of interest for lithium ion batteries since Li–Si

• alloys have an incredibly high gravimetric lithium storage capacity. He at al. have used MLD to encapsulate Si nanoparticles with alucone for this application [49]. The alucone layer prevents the formation of a resistive secondary electrolyte interphase (SEI), thus yielding improved electrode performance

• . Gleason and coworkers, having previously shown pV4D4 as potential solid electrolyte, are exploring the Si nanowire assembly in Figure 8a as a route toward anodes for micro lithium ion batteries [39]. Figure 9e shows a corresponding, conformal pV4D4 coating on a lithium spinel oxide particle, a material

Synthesis of graphene–transition metal oxide hybrid nanoparticles and their application in various fields

• Arpita Jana,
• Elke Scheer and
• Sebastian Polarz

Beilstein J. Nanotechnol. 2017, 8, 688–714, doi:10.3762/bjnano.8.74

• ) and therefore offers the possibility to fabricate a large variety of graphene–transition metal oxide (TMO) NP hybrids. These hybrid materials are promising alternatives to reduce the drawbacks of using only TMO NPs in various applications, such as anode materials in lithium ion batteries (LIBs

• fields. Material property requirements for specific applications Graphite is commercially used as an anode material for LIBs due to its large lithium storage capacity of 372 mAh·g−1. However, this is not sufficient for applications requiring high energy capacity. Single layer graphene has a high

• theoretical lithium storage capacity of 744 mAh·g−1, but graphene has a tendency to stack due to van der Waals interactions between graphene layers [24]. The incorporation of TMO NPs inhibits the aggregation of graphene layers [25]. Poizot et al. first introduced the concept of utilising electrodes made of

Carbon nanotube-wrapped Fe₂O₃ anode with improved performance for lithium-ion batteries

• Guoliang Gao,
• Yan Jin,
• Qun Zeng,
• Deyu Wang and
• Cai Shen

Beilstein J. Nanotechnol. 2017, 8, 649–656, doi:10.3762/bjnano.8.69

• material of lithium-ion batteries (LIBs) because they offer high theoretical capacities, and are environmentally friendly and widely available. However, the low electronic conductivity and severe irreversible lithium storage have hindered a practical application. Herein, we employed ethanolamine as

• precursor to prepare Fe2O3/COOH-MWCNT composites through a simple hydrothermal synthesis. When these composites were used as electrode material in lithium-ion batteries, a reversible capacity of 711.2 mAh·g−1 at a current density of 500 mA·g−1 after 400 cycles was obtained. The result indicated that Fe2O3

• /COOH-MWCNT composite is a potential anode material for lithium-ion batteries. Keywords: anode material; carbon nanotubes; hydrothermal synthesis method; lithium-ion batteries; Introduction The depletion of non-renewable energy resources such as coal, petrol and natural gas has led to the urgent need

Role of oxygen in wetting of copper nanoparticles on silicon surfaces at elevated temperature

• Tapas Ghosh and
• Biswarup Satpati

Beilstein J. Nanotechnol. 2017, 8, 425–433, doi:10.3762/bjnano.8.45

• recent years, several CuO nanostructure syntheses and their applications have been reported. Different shaped CuO nanostructures such as nanowires, nanoplatelets, nanorods, and nanoflowers have been employed as the anode material for lithium ion batteries [4][5][6][7], and improved performance has also

Phosphorus-doped silicon nanorod anodes for high power lithium-ion batteries

• Chao Yan,
• Qianru Liu,
• Jianzhi Gao,
• Zhibo Yang and
• Deyan He

Beilstein J. Nanotechnol. 2017, 8, 222–228, doi:10.3762/bjnano.8.24

• were fabricated on CuO nanorods for application in high power lithium-ion batteries. Since the conductivity of lithiated CuO is significantly better than that of CuO, after the first discharge, the voltage cut-off window was then set to the range covering only the discharge–charge range of Si. Thus

• . Keywords: in situ reduction; lithium-ion battery; silicon anode; silicon nanorods; Introduction As one of the most popular secondary power sources, lithium-ion batteries (LIBs) are widely used in portable personal electronics, electrical vehicles and grid energy storage because of their high energy and

• . Phosphorus-doped Si anodes are assumed to undergo less volume changes than undoped anodes during Li-ion insertion and extraction. This is because some positions are taken by phosphorus and phosphorus is inactive for Li-ion, which means less lithium will be intercalated. Meanwhile, phosphorus doping could

Effect of Anderson localization on light emission from gold nanoparticle aggregates

• Mohamed H. Abdellatif,
• Marco Salerno,
• Gaser N. Abdelrasoul,
• Ioannis Liakos,
• Alice Scarpellini,
• Sergio Marras and
• Alberto Diaspro

Beilstein J. Nanotechnol. 2016, 7, 2013–2022, doi:10.3762/bjnano.7.192

• phosphate, potassium titanyl phosphate or lithium niobate. This effect can be ascribed to the fractal-like shape or statistical self-similarity of the AuNP arrangement [14]. The concept of fractal-like design in optics was introduced for the first time by Stockman [14]. In a chain of particles, the self

Effect of nanostructured carbon coatings on the electrochemical performance of Li_1.4Ni_0.5Mn_0.5O_2+x-based cathode materials

• Konstantin A. Kurilenko,
• Oleg A. Shlyakhtin,
• Oleg A. Brylev,
• Dmitry I. Petukhov and
• Alexey V. Garshev

Beilstein J. Nanotechnol. 2016, 7, 1960–1970, doi:10.3762/bjnano.7.187

• lithium diffusion coefficient, a higher specific capacity and lower values of charge transfer resistance, which can be related to the more uniform carbon coatings and to the significant content of sp2-hybridized carbon detected by XPS and by Raman spectroscopy. Keywords: carbon coatings; electrode

• to the practical application of LiNi0.5Mn0.5O2 is related to the internal ion exchange (ion mixing) of Li+ and Ni2+ due to the very similar ionic radii. This process could be partially suppressed by the introduction of extra lithium into LiNi0.5Mn0.5O2. Extra lithium ions are usually located in the

• modification, namely other cathode materials (LiMnPO4 [11], LiMn2O4 [12], LiCoO2 [13], LiNiO2 [14]) or simple binary compounds such as CaF2 [15], TiO2 [16], ZnO [17] and Al2O3 [18]. During the assembly of the lithium-ion cells, the cathode materials are always mechanically mixed with carbon black in order to

Microwave synthesis of high-quality and uniform 4 nm ZnFe₂O₄ nanocrystals for application in energy storage and nanomagnetics

• Christian Suchomski,
• Ben Breitung,
• Ralf Witte,
• Michael Knapp,
• Sondes Bauer,
• Tilo Baumbach,
• Christian Reitz and
• Torsten Brezesinski

Beilstein J. Nanotechnol. 2016, 7, 1350–1360, doi:10.3762/bjnano.7.126

• good material characteristics, it is remarkable that the microwave-based synthetic route is simple, easily reproducible and scalable. Keywords: 1-phenylethanol route; lithium-ion battery; nanomagnetism; nanoparticles; nonaqueous sol–gel synthesis; zinc ferrite; Introduction Spinel ferrites of the

• vacuum at 80 °C for 12 h. The areal loading was 2.4 mgZFO/cm2 on average. Coin-type cells with 600 µm-thick Li metal foil (Rockwood Lithium Inc.) and glass microfiber film separator (Whatman, GF/D grade) were assembled inside an argon-filled glovebox (MBraun) with [O2] and [H2O] < 1 ppm. The electrolyte

Improved lithium-ion battery anode capacity with a network of easily fabricated spindle-like carbon nanofibers

• Mengting Liu,
• Wenhe Xie,
• Lili Gu,
• Tianfeng Qin,
• Xiaoyi Hou and
• Deyan He

Beilstein J. Nanotechnol. 2016, 7, 1289–1295, doi:10.3762/bjnano.7.120

• into the amorphous carbon matrix. When directly used as a binder-free anode for lithium-ion batteries, the network showed excellent electrochemical performance with high capacity, good rate capacity and reliable cycling stability. Under a current density of 0.2 A g−1, it delivered a high reversible

• capacity of 875.5 mAh g−1 after 200 cycles and 1005.5 mAh g−1 after 250 cycles with a significant coulombic efficiency of 99.5%. Keywords: carbon nanofiber network; electrospinning; lithium-ion battery; manganese oxide; nitrogen modification; Introduction Lithium-ion batteries (LIBs) have been identified

• , a network of spindle-like carbon nanofibers anchored with MnO and N for LIB anodes was fabricated via a simplified synthesis route involving electrospinning followed by preoxidation in air and postcarbonization in Ar. The microstructure, chemical composition and electrochemical lithium storage

Mesoporous hollow carbon spheres for lithium–sulfur batteries: distribution of sulfur and electrochemical performance

• Anika C. Juhl,
• Artur Schneider,
• Boris Ufer,
• Torsten Brezesinski,
• Jürgen Janek and
• Michael Fröba

Beilstein J. Nanotechnol. 2016, 7, 1229–1240, doi:10.3762/bjnano.7.114

• the use in lithium–sulfur batteries because of the large internal void offering space for sulfur and polysulfide storage and confinement. However, there is an ongoing discussion whether the cavity is accessible for sulfur. Yet no valid proof of cavity filling has been presented, mostly due to

• mass of sulfur over 500 cycles. Keywords: carbon/sulfur composites; cycling stability; distribution of sulfur in pores; hollow carbon spheres; lithium–sulfur batteries; Introduction In the past 20 years, rechargeable lithium–ion batteries have proven to be superior energy storage devices and have

• the high theoretical specific capacity (1675 mAh·g−1) and specific energy (2600 Wh·kg−1) of sulfur the lithium–sulfur (Li–S) battery is a promising candidate to overcome this limitation and, thus, replace the Li–ion system [4][6]. Besides, sulfur offers the advantages of being naturally abundant, non

Reasons and remedies for the agglomeration of multilayered graphene and carbon nanotubes in polymers

• Rasheed Atif and
• Fawad Inam

Beilstein J. Nanotechnol. 2016, 7, 1174–1196, doi:10.3762/bjnano.7.109

• introduction of heteroatoms in SWNTs can lead to novel properties. Heating may remove the attached functionalized groups. The functionalized SWNTs can be dissolved in organic solvents up to about 100 mg/L. The functionalization of SWNTs in liquid ammonia by reductive alkylation using lithium and alkyl halides

• nanocomposites [2]. Oxidation of SWNTs: The oxidation of CNTs surface is possible by, for instance, heat treatment in oxygen and air, plasma treatment, chemical treatment and ozone treatment. Oxidation can also be carried out in lithium aluminum hydride solution [41]. Table 3 shows different oxidation methods

Manufacturing and investigation of physical properties of polyacrylonitrile nanofibre composites with SiO₂, TiO₂ and Bi₂O₃ nanoparticles

• Tomasz Tański,
• Wiktor Matysiak and
• Barbara Hajduk

Beilstein J. Nanotechnol. 2016, 7, 1141–1155, doi:10.3762/bjnano.7.106

• produced by using electrospinning from solutions of polymers based on polyacrylonitrile (PAN) and N,N-dimethylformamide (DMF) with ceramic nanoparticles of SiO2/TiO2/Bi2O3. PAN/SiO2 composite nanofibres are used as membranes in the production of air filters, gas absorbents and new types of lithium-ion

• obtained composite mats, reinforced with silicon oxide, are a promising starting material that can be used to produce carbon anodes, which are used in lithium-ion batteries, after their subsequent treatment by carbonisation and chemical removal of the reinforcing phases in order to increase the porosity of

Reconstitution of the membrane protein OmpF into biomimetic block copolymer–phospholipid hybrid membranes

• Matthias Bieligmeyer,
• Franjo Artukovic,
• Stephan Nussberger,
• Thomas Hirth,
• Thomas Schiestel and
• Michaela Müller

Beilstein J. Nanotechnol. 2016, 7, 881–892, doi:10.3762/bjnano.7.80

• block copolymers. (A) Reaction scheme for the synthesis of poly(1,4-isoprene-block-ethylene oxide) block copolymers. Anionic polymerization of isoprene in toluene was initiated with sec-butyl lithium. Sequential polymerization of ethylene oxide was enabled by triisobutyl aluminium. (B) Size exclusion

Unraveling the neurotoxicity of titanium dioxide nanoparticles: focusing on molecular mechanisms

• Bin Song,
• Yanli Zhang,
• Jia Liu,
• Xiaoli Feng,
• Ting Zhou and
• Longquan Shao

Beilstein J. Nanotechnol. 2016, 7, 645–654, doi:10.3762/bjnano.7.57

• characteristics [1] including antibacterial, ultraviolet-absorbing, photocatalytic, and self-cleaning properties [2]. Thus, TiO2 NPs are widely used in cosmetics, sun screens, ceramics, paints, packaging, lithium batteries, the food industry, and in medical applications [3]. However, the rapid development of

Synthesis and applications of carbon nanomaterials for energy generation and storage

• Marco Notarianni,
• Jinzhang Liu,
• Kristy Vernon and
• Nunzio Motta

Beilstein J. Nanotechnol. 2016, 7, 149–196, doi:10.3762/bjnano.7.17

Linear and nonlinear optical properties of hybrid metallic–dielectric plasmonic nanoantennas

• Mario Hentschel,
• Bernd Metzger,
• Bastian Knabe,
• Karsten Buse and
• Harald Giessen

Beilstein J. Nanotechnol. 2016, 7, 111–120, doi:10.3762/bjnano.7.13

• process, we demonstrate the ability to selectively and reproducibly fill the gap region of nanoantennas with dielectric nanoparticles made of lithium niobate (LiNbO3) with high efficiency. The linear optical properties of the antennas are modified due to the large refractive index of the material. This

• , depending on its microscopic nonlinearity. Results and Discussion One obvious idea drawn from these earlier experiments is thus to use standard nonlinear materials such as lithium niobate crystals (LiNbO3) or indium tin oxide (ITO) and selectively position them inside the gaps of nanoantennas, as shown in

• increased spectral overlap of the laser source and the plasmon spectrum. There are actually several possible explanations for the observed behavior: Firstly, lithium niobate (under these circumstances) is a poor frequency converter. Lithium niobate exhibits an off-resonant nonlinearity which becomes

Surfactant-controlled composition and crystal structure of manganese(II) sulfide nanocrystals prepared by solvothermal synthesis

• Elena Capetti,
• Anna M. Ferretti,
• Vladimiro Dal Santo and
• Alessandro Ponti

Beilstein J. Nanotechnol. 2015, 6, 2319–2329, doi:10.3762/bjnano.6.238

• ), ≈100 K (β-MnS), and 154 K (α-MnS) [6]. The interesting physical properties and the rich polymorphism prompted research on MnS nanocrystals (NCs) in view of applications as photoluminescent components [7], photoreduction catalysts [8], anode materials in lithium-ion batteries [9], and supercapacitor

Nitrogen-doped graphene films from chemical vapor deposition of pyridine: influence of process parameters on the electrical and optical properties

• Andrea Capasso,
• Theodoros Dikonimos,
• Francesca Sarto,
• Alessio Tamburrano,
• Giovanni De Bellis,
• Maria Sabrina Sarto,
• Giuliana Faggio,
• Angela Malara,
• Giacomo Messina and
• Nicola Lisi

Beilstein J. Nanotechnol. 2015, 6, 2028–2038, doi:10.3762/bjnano.6.206

• nitrogen might also confer useful chemical properties to graphene, e.g., rendering it catalytic to oxygen reduction reactions [24] or enhancing its lithium intercalation properties for battery applications [25]. Nitrogen doping was originally achieved ex situ by the post-growth treatment of pristine CVD

Metal hydrides: an innovative and challenging conversion reaction anode for lithium-ion batteries

• Luc Aymard,
• Yassine Oumellal and
• Jean-Pierre Bonnet

Beilstein J. Nanotechnol. 2015, 6, 1821–1839, doi:10.3762/bjnano.6.186

• .6.186 Abstract The state of the art of conversion reactions of metal hydrides (MH) with lithium is presented and discussed in this review with regard to the use of these hydrides as anode materials for lithium-ion batteries. A focus on the gravimetric and volumetric storage capacities for different

• electrode polarization (<0.2 V) for conversion materials. Conversion process reaction mechanisms with lithium are subsequently detailed for MgH2, TiH2, complex hydrides Mg2MHx and other Mg-based hydrides. The reversible conversion reaction mechanism of MgH2, which is lithium-controlled, can be extended to

• kinetics improvement and reversibility is presented. Drastic technological improvement in order to the enhance conversion process efficiencies is needed for practical applications. The main goals are minimizing the impact of electrode volume variation during lithium extraction and overcoming the poor

Materials for sustainable energy production, storage, and conversion

• Maximilian Fichtner

Beilstein J. Nanotechnol. 2015, 6, 1601–1602, doi:10.3762/bjnano.6.163

• the demands of future applications. Efficient systems based on powerful and sustainable materials beyond lithium are needed in order to provide long term solutions. In this respect, three contributions were selected from Rana Mohtadi, Luc Aymard, and Philip Adelhelm [4][5][6], presenting the progress

Charge carrier mobility and electronic properties of Al(Op)₃: impact of excimer formation

• Andrea Magri,
• Pascal Friederich,
• Bernhard Schäfer,
• Valeria Fattori,
• Xiangnan Sun,
• Timo Strunk,
• Velimir Meded,
• Luis E. Hueso,
• Wolfgang Wenzel and
• Mario Ruben

Beilstein J. Nanotechnol. 2015, 6, 1107–1115, doi:10.3762/bjnano.6.112

• -phenalen-9-olate to sensitize the europium ion. Furthermore, for lithium and sodium, the enhancement was found to be the most efficient. In these works, 9-hydroxyphenalen-1-one was carefully chosen for its photophysical properties, namely, its high absorption cross section in the condensed phase between

From lithium to sodium: cell chemistry of room temperature sodium–air and sodium–sulfur batteries

• Philipp Adelhelm,
• Pascal Hartmann,
• Conrad L. Bender,
• Martin Busche,
• Christine Eufinger and
• Juergen Janek

Beilstein J. Nanotechnol. 2015, 6, 1016–1055, doi:10.3762/bjnano.6.105

• , Germany 10.3762/bjnano.6.105 Abstract Research devoted to room temperature lithium–sulfur (Li/S8) and lithium–oxygen (Li/O2) batteries has significantly increased over the past ten years. The race to develop such cell systems is mainly motivated by the very high theoretical energy density and the

• . This review provides a summary of the state-of-the-art knowledge on lithium–sulfur and lithium–oxygen batteries and a direct comparison with the analogous sodium systems. The general properties, major benefits and challenges, recent strategies for performance improvements and general guidelines for

• further development are summarized and critically discussed. In general, the substitution of lithium for sodium has a strong impact on the overall properties of the cell reaction and differences in ion transport, phase stability, electrode potential, energy density, etc. can be thus expected. Whether

Multiscale modeling of lithium ion batteries: thermal aspects

• Arnulf Latz and
• Jochen Zausch

Beilstein J. Nanotechnol. 2015, 6, 987–1007, doi:10.3762/bjnano.6.102

• .6.102 Abstract The thermal behavior of lithium ion batteries has a huge impact on their lifetime and the initiation of degradation processes. The development of hot spots or large local overpotentials leading, e.g., to lithium metal deposition depends on material properties as well as on the nano- und

• special cases the averaged thermal behavior can be captured very well by porous electrode theory. Keywords: lithium ion batteries; multiscale modeling; heat transport; Introduction The main challenge for establishing an ab initio multiscale simulation approach for batteries or electrochemical storage

• absolute accuracy of the DFT simulation, which usually contain many simplification and assumptions on the structure of the solution [4][5]. By using cluster expansions [8] it is possible to combine DFT with kinetic Monte Carlo (KMC) simulations to obtain collective diffusion coefficients for lithium ions