Proximity effect in a two-dimensional electron gas coupled to a thin superconducting layer

• Christopher Reeg,
• Daniel Loss and
• Jelena Klinovaja

Beilstein J. Nanotechnol. 2018, 9, 1263–1271, doi:10.3762/bjnano.9.118

• advances of the past few years was the successful epitaxial growth of thin layers of superconducting Al on InAs and InSb nanowires [38][39][40][41][42]. The intimate contact between the semiconductor and superconductor in these devices ensures a hard induced superconducting gap. Recently, this epitaxial

P3HT:PCBM blend films phase diagram on the base of variable-temperature spectroscopic ellipsometry

• Barbara Hajduk,
• Henryk Bednarski,
• Bożena Jarząbek,
• Henryk Janeczek and
• Paweł Nitschke

Beilstein J. Nanotechnol. 2018, 9, 1108–1115, doi:10.3762/bjnano.9.102

• clear advantages of this method are the possibility to directly monitor the phase behavior of P3HT:PCBM thin layers and to accurately estimate their characteristic temperatures. In addition, this method allows one to omit a time-consuming theoretical analysis of ellipsometric data and limits the

Synthesis and characterization of two new TiO₂-containing benzothiazole-based imine composites for organic device applications

• Anna Różycka,
• Agnieszka Iwan,
• Krzysztof Artur Bogdanowicz,
• Michal Filapek,
• Natalia Górska,
• Damian Pociecha,
• Marek Malinowski,
• Patryk Fryń,
• Agnieszka Hreniak,
• Jakub Rysz,
• Paweł Dąbczyński and
• Monika Marzec

Beilstein J. Nanotechnol. 2018, 9, 721–739, doi:10.3762/bjnano.9.67

• materials was investigated. Thin layers of SP2 and SP2:TiO2 composites in various weight ratios were prepared by dropping the solution on a glass substrate and annealed on the hot plate at 60 °C to evaporate the solvent (chlorobenzene). Since layers prepared from SP1 and TiO2 using the same technique turned

Engineering of oriented carbon nanotubes in composite materials

• Razieh Beigmoradi,
• Abdolreza Samimi and
• Davod Mohebbi-Kalhori

Beilstein J. Nanotechnol. 2018, 9, 415–435, doi:10.3762/bjnano.9.41

• membrane could be coated by cellulose acetate (CA) solution. Frictional orientation The frictional orientation method is known as the doctor blade (DB) technique or tape casting. This technique is widely used to produce a variety of thin layers and coat substrates with wet films. A blade or a spiral film

Electron interaction with copper(II) carboxylate compounds

• Michal Lacko,
• Peter Papp,
• Iwona B. Szymańska,
• Edward Szłyk and
• Štefan Matejčík

Beilstein J. Nanotechnol. 2018, 9, 384–398, doi:10.3762/bjnano.9.38

• materials for preparation of thin layers or 3D nanostructures. Complexes and metalorganic compounds are used as precursors in modern nano scale layer techniques. After activation, molecules undergo dissociation on the surface. Volatile parts of molecules are removed from the surface while a metal component

BN/Ag hybrid nanomaterials with petal-like surfaces as catalysts and antibacterial agents

• Konstantin L. Firestein,
• Denis V. Leybo,
• Alexander E. Steinman,
• Andrey M. Kovalskii,
• Andrei T. Matveev,
• Anton M. Manakhov,
• Irina V. Sukhorukova,
• Pavel V. Slukin,
• Nadezda K. Fursova,
• Sergey G. Ignatov,
• Dmitri V. Golberg and
• Dmitry V. Shtansky

Beilstein J. Nanotechnol. 2018, 9, 250–261, doi:10.3762/bjnano.9.27

• ] that BN/Ag hybrid nanomaterials may possess high activity and stability as catalysts for oxidation of organic compounds. Moreover, N-impurities and other defects in thin layers of raw h-BN can act as active centers for oxygen reduction reactions [15]. Generally, the catalytic activity of BN/Ag hybrid

Al₂O₃/TiO₂ inverse opals from electrosprayed self-assembled templates

• Arnau Coll,
• Sandra Bermejo,
• David Hernández and
• Luís Castañer

Beilstein J. Nanotechnol. 2018, 9, 216–223, doi:10.3762/bjnano.9.23

• easily conformally deposited in thin layers of a few nanometers thick and has the advantage that the deposition temperature is compatible with the maximum temperature that the polystyrene nanoparticles can withstand (<100 °C). The ALD process uses trimethylaluminum (TMA) as the precursor gas. The

L-Lysine-grafted graphene oxide as an effective adsorbent for the removal of methylene blue and metal ions

• Yan Yan,
• Jie Li,
• Fangbei Kong,
• Kuankuan Jia,
• Shiyu He and
• Baorong Wang

Beilstein J. Nanotechnol. 2017, 8, 2680–2688, doi:10.3762/bjnano.8.268

• . Finally, the morphology of as-prepared graphene materials was characterized by SEM (Figure 3). GO exhibits a structure of the ultra-thin layers with little wrinkles in (Figure 3b). More wrinkled and folded nanosheets of Lys-GO can be clearly seen in Figure 3a. These results showed that the as-prepared Lys

Optical contrast and refractive index of natural van der Waals heterostructure nanosheets of franckeite

• Patricia Gant,
• Foad Ghasemi,
• David Maeso,
• Carmen Munuera,
• Elena López-Elvira,
• Riccardo Frisenda,
• David Pérez De Lara,
• Gabino Rubio-Bollinger,
• Mar Garcia-Hernandez and
• Andres Castellanos-Gomez

Beilstein J. Nanotechnol. 2017, 8, 2357–2362, doi:10.3762/bjnano.8.235

• the illumination wavelength and the SiO2 thickness to determine the optimal SiO2 capping layer to facilitate the identification of franckeite thin layers. Supporting Information Supporting Information features additional data about an example of cylindrite, the reflectance determination of different

Ta₂N₃ nanocrystals grown in Al₂O₃ thin layers

• Krešimir Salamon,
• Maja Buljan,
• Iva Šarić,
• Mladen Petravić and
• Sigrid Bernstorff

Beilstein J. Nanotechnol. 2017, 8, 2162–2170, doi:10.3762/bjnano.8.215

A systematic study of the controlled generation of crystalline iron oxide nanoparticles on graphene using a chemical etching process

• Peter Krauß,
• Jörg Engstler and
• Jörg J. Schneider

Beilstein J. Nanotechnol. 2017, 8, 2017–2025, doi:10.3762/bjnano.8.202

• additional polymer coating is often deposited on the monolayer prior to the etching process to provide mechanical support for the graphene, preventing it from tearing and ripping [14][22][23][24][29][30][31]. Most common are thin layers of poly(methyl methacrylate) (PMMA) which can be easily deposited by

Evaluation of preparation methods for suspended nano-objects on substrates for dimensional measurements by atomic force microscopy

• Petra Fiala,
• Daniel Göhler,
• Benno Wessely,
• Michael Stintz,
• Giovanni Mattia Lazzerini and
• Andrew Yacoot

Beilstein J. Nanotechnol. 2017, 8, 1774–1785, doi:10.3762/bjnano.8.179

• velocity therefore defines the layer thickness, i.e., an increase in the velocity leads to an increase in the thickness. Afterwards, excess liquid is drained and the remaining layer evaporated. Dip coating is preferred method for producing (self-organising) thin layers on substrates, but particles also can

Synthesis, spectroscopic characterization and thermogravimetric analysis of two series of substituted (metallo)tetraphenylporphyrins

• Rasha K. Al-Shewiki,
• Carola Mende,
• Roy Buschbeck,
• Pablo F. Siles,
• Oliver G. Schmidt,
• Tobias Rüffer and
• Heinrich Lang

Beilstein J. Nanotechnol. 2017, 8, 1191–1204, doi:10.3762/bjnano.8.121

• possible and we are recently fabricating thin layers of these compounds by spin-coating [31]. Conclusion Two series of metalloporphyrins MTPP(C(O)NR2)4 (M = CoII, NiII, CuII, ZnII) derived out of their free-base species H2TPP(C(O)NR2)4 (R = Me (2/2a–d), iPr (3/3a–d)) were synthesized and characterized by

Nanoantenna-assisted plasmonic enhancement of IR absorption of vibrational modes of organic molecules

• Alexander G. Milekhin,
• Olga Cherkasova,
• Sergei A. Kuznetsov,
• Ilya A. Milekhin,
• Ekatherina E. Rodyakina,
• Alexander V. Latyshev,
• Sreetama Banerjee,
• Georgeta Salvan and
• Dietrich R. T. Zahn

Beilstein J. Nanotechnol. 2017, 8, 975–981, doi:10.3762/bjnano.8.99

• molecules, often investigated as promising candidates for molecular spintronics [5][6]. There have been studies on molecule/metal interfaces [7], magnetic coupling in the metal phthalocyanine layers [8], spin transport or magnetic properties through single molecules or even thin layers [6][9][10] of

Analysis and modification of defective surface aggregates on PCDTBT:PCBM solar cell blends using combined Kelvin probe, conductive and bimodal atomic force microscopy

• Hanaul Noh,
• Alfredo J. Diaz and
• Santiago D. Solares

Beilstein J. Nanotechnol. 2017, 8, 579–589, doi:10.3762/bjnano.8.62

• compositional variation occurs in the entire volume of the active layer. However, since SPM methods primarily characterize the surface (with or without tip–sample contact), we conclude that the ultra-thin layers investigated in this report rest on the surface. We also point out that the samples used here are

• aggregates and modification of their structures on PCDTBT-based polymer solar cells using combined Kelvin probe (KPFM), conductive (C-AFM) and bimodal atomic force microscopy (AFM). Topography changes for partly removed aggregates show that the aggregates are composed of molecular thin layers of about 0.8 nm

The longstanding challenge of the nanocrystallization of 1,3,5-trinitroperhydro-1,3,5-triazine (RDX)

• Florent Pessina and
• Denis Spitzer

Beilstein J. Nanotechnol. 2017, 8, 452–466, doi:10.3762/bjnano.8.49

• quartz substrate and pressing into tablets). Mil’chenko et al. [41] delved further in the physical vapor deposition (PVD) process with the deposition of 2,4,6-triamino-1,3,5-trinitrobenzene (TATB), HMX, RDX, PETN and BTF as thin layers on several substrates such as plexiglas and copper while changing

Photocatalysis applications of some hybrid polymeric composites incorporating TiO₂ nanoparticles and their combinations with SiO₂/Fe₂O₃

• Andreea Laura Chibac,
• Tinca Buruiana,
• Violeta Melinte and
• Emil C. Buruiana

Beilstein J. Nanotechnol. 2017, 8, 272–286, doi:10.3762/bjnano.8.30

• order to ensure a very homogeneous composition of the formulations). Then, these formulations were cast in thin layers on a teflon plate and further subjected to UV irradiation for a period of 600 s, using Irgacure 819 (1 wt %) as photoinitiator, to finally yiled thin films (thickness around 0.2 mm

Nanostructured SnO₂–ZnO composite gas sensors for selective detection of carbon monoxide

• Paul Chesler,
• Cristian Hornoiu,
• Susana Mihaiu,
• Cristina Vladut,
• Jose Maria Calderon Moreno,
• Mihai Anastasescu,
• Carmen Moldovan,
• Bogdan Firtat,
• Costin Brasoveanu,
• George Muscalu,
• Ion Stan and
• Mariuca Gartner

Beilstein J. Nanotechnol. 2016, 7, 2045–2056, doi:10.3762/bjnano.7.195

• ]. The oxide-based semiconductor sensors have been used worldwide to detect toxic, hazardous and combustible gases (e.g., C2H5OH, H2S, H2, various hydrocarbons, volatile organic compounds) for the safety of humans and for a better control over the surrounding environment [1][2][3]. Thin layers of metal

Cubic chemically ordered FeRh and FeCo nanomagnets prepared by mass-selected low-energy cluster-beam deposition: a comparative study

• Veronique Dupuis,
• Anthony Robert,
• Arnaud Hillion,
• Ghassan Khadra,
• Nils Blanc,
• Damien Le Roy,
• Florent Tournus,
• Clement Albin,
• Olivier Boisron and
• Alexandre Tamion

Beilstein J. Nanotechnol. 2016, 7, 1850–1860, doi:10.3762/bjnano.7.177

• protect the sample from oxidation but also to allow vacuum high-temperature annealing and so to reach the equilibrium phase without coalescence of the NPs. To characterise the structure of the clusters by transmission electron microscopy (TEM), we prepared discontinuous thin layers of NPs deposited on an

Numerical investigation of depth profiling capabilities of helium and neon ions in ion microscopy

• Patrick Philipp,
• Lukasz Rzeznik and
• Tom Wirtz

Beilstein J. Nanotechnol. 2016, 7, 1749–1760, doi:10.3762/bjnano.7.168

• thin layers, the separation of the layers is even worse. Data from Figure 4 and Figure 5 along with results from samples #1 and #6 is used to reconstruct the depth profiles for the different species present in the polymer samples (Figure 6). Depth profiles are shown for sample #1 with 10 to 20 nm thick

Nanostructured TiO₂-based gas sensors with enhanced sensitivity to reducing gases

• Wojciech Maziarz,
• Anna Kusior and
• Anita Trenczek-Zajac

Beilstein J. Nanotechnol. 2016, 7, 1718–1726, doi:10.3762/bjnano.7.164

• influencing the sensitivity of a gas sensor. In comparison with spherical materials or thin layers, 3D structures exhibit much more active sites, and a complex network of canals enables gaseous reagents to penetrate inside the structure. The smaller the grains, the higher the surface-to-volume ratio for a gas

Sb₂S₃ grown by ultrasonic spray pyrolysis and its application in a hybrid solar cell

• Erki Kärber,
• Atanas Katerski,
• Ilona Oja Acik,
• Arvo Mere,
• Valdek Mikli and
• Malle Krunks

Beilstein J. Nanotechnol. 2016, 7, 1662–1673, doi:10.3762/bjnano.7.158

• the EQE result, the integrated product the EQE(λ) and solar irradiance IAM1.5(λ) was calculated by using the online tool Open Photovoltaics Analysis Platform, and compared with the JSC obtained from the current–voltage scan. Raman spectra A–D of thin layers grown by spraying solutions with Sb/S

Polystyrene-block-poly(ethylene oxide) copolymers as templates for stacked, spherical large-mesopore silica coatings: dependence of silica pore size on the PS/PEO ratio

• Roberto Nisticò,
• Giuliana Magnacca,
• Sushilkumar A. Jadhav and
• Dominique Scalarone

Beilstein J. Nanotechnol. 2016, 7, 1454–1460, doi:10.3762/bjnano.7.137

• copolymer films obtained by spin-coating deposition of block copolymer micellar solutions were transformed into silica nanoporous thin layers by thermal treatment performed in air. This way, the organic templating species (i.e., block copolymers) were degraded and removed, leaving voids which formed the

• the mesoporous silica thin layers Mesoporous silica thin films were synthesized by a sol–gel reaction of tetraethyl orthosilicate (TEOS, ≥ 99.0%, Aldrich) in ethanol (≥ 95.0%, Carlo Erba Reagents) under acidic conditions (HCl 37 wt %, Fluka Chemika) as reported in [19]. Different sol–gel solutions

• cm × 15 mm, at 1000 rpm for 20 s, using an 8” Desktop Precision Spin Coating System, model P-6708D vs. 2.0. After deposition, the films were dried in a hood at rt for at least 12 h in order to reach complete evaporation of solvents. Hybrid films were then transformed into silica nanostructured thin

Viability and proliferation of endothelial cells upon exposure to GaN nanoparticles

• Tudor Braniste,
• Ion Tiginyanu,
• Tibor Horvath,
• Simion Raevschi,
• Serghei Cebotari,
• Marco Lux,
• Axel Haverich and
• Andres Hilfiker

Beilstein J. Nanotechnol. 2016, 7, 1330–1337, doi:10.3762/bjnano.7.124

• functionalized surfaces of implants or prosthesis could be easily modulated from the exterior (e.g., with an ultrasound field), making surfaces either more or less attractive for desired types. Experimental Preparation of GaN nanoparticles Thin layers of GaN were grown on ZnO nanoparticles by hydride vapor phase

The self-similarity theory of high pressure torsion

• Yan Beygelzimer,
• Roman Kulagin,
• Laszlo S. Toth and
• Yulia Ivanisenko

Beilstein J. Nanotechnol. 2016, 7, 1267–1277, doi:10.3762/bjnano.7.117

• the deformation in two thin layers near the plain surfaces of the anvils. One can verify by direct substitution that a velocity field in the form of two thin layers of simple shear separated by a cylindrical rigid zone is also a solution of the HPT problem for a perfectly plastic body when m = 0. This