Tin dioxide nanomaterial-based photocatalysts for nitrogen oxide oxidation: a review

• Viet Van Pham,
• Hong-Huy Tran,
• Thao Kim Truong and
• Thi Minh Cao

Beilstein J. Nanotechnol. 2022, 13, 96–113, doi:10.3762/bjnano.13.7

• introducing defects in metal oxide semiconductors opens up the possibility of their use in the visible spectrum [77]. Recently, Xie et al. reported using SnO2/graphene quantum dot (GQD) composites. They showed that the absorption edge of as-prepared SnO2 (Figure 13a black line) is around 340 nm, equaling to a

Sputtering onto liquids: a critical review

• Anastasiya Sergievskaya,
• Adrien Chauvin and
• Stephanos Konstantinidis

Beilstein J. Nanotechnol. 2022, 13, 10–53, doi:10.3762/bjnano.13.2

• NPs with desired size, shape, and composition [2]. Colloidal synthesis allows one to obtain metal, oxide, halide, chalcogenide, and other types of NPs but the mechanisms of their formation are different, even though all of them include an initial nucleation step followed by a growth step [77]. In this

Identifying diverse metal oxide nanomaterials with lethal effects on embryonic zebrafish using machine learning

• Richard Liam Marchese Robinson,
• Haralambos Sarimveis,
• Philip Doganis,
• Xiaodong Jia,
• Marianna Kotzabasaki,
• Christiana Gousiadou,
• Stacey Lynn Harper and
• Terry Wilkins

Beilstein J. Nanotechnol. 2021, 12, 1297–1325, doi:10.3762/bjnano.12.97

• , embryonic zebrafish (Danio Rerio) are recognised as a key human safety relevant in vivo test system. Hence, machine learning models were developed for identifying metal oxide nanomaterials causing lethality to embryonic zebrafish up to 24 hours post-fertilisation, or excess lethality in the period of 24–120

• -based magnetic resonance imaging (MRI) contrast agent (Feridex) was withdrawn from the market, following concerns regarding its observed side effects [2][7]. In spite of concerns around safety [7][8][9] and other challenges [10], there remains interest in developing novel metal oxide nanomaterials for

• various biomedical applications [10][11][12], as well as applications in other areas, such as in agriculture [13]. Nonetheless, the possibility that novel metal oxide ENMs developed for applications, such as biomedical applications, could be harmful to human health [8][9], means that there is a real need

Plasmon-enhanced photoluminescence from TiO₂ and TeO₂ thin films doped by Eu³⁺ for optoelectronic applications

• Marcin Łapiński,
• Jakub Czubek,
• Katarzyna Drozdowska,
• Anna Synak,
• Wojciech Sadowski and
• Barbara Kościelska

Beilstein J. Nanotechnol. 2021, 12, 1271–1278, doi:10.3762/bjnano.12.94

• . Interestingly, no transition caused by the electric dipole (615 nm, typical for Eu3+ ions) was observed in the emission spectrum for both kinds of metal oxide matrix. The main emission peak corresponds to the transition occurring via magnetic dipole, which is independent of the host matrix. Such a phenomenon

Morphology-driven gas sensing by fabricated fractals: A review

• Vishal Kamathe and
• Rupali Nagar

Beilstein J. Nanotechnol. 2021, 12, 1187–1208, doi:10.3762/bjnano.12.88

• metal oxide (SMO) sensors are most popular due to their low cost, simplicity, easy fabrication, and wide range of gas detection capabilities [9]. Thin films and nanostructures exhibit better sensing characteristics. Various researchers have reported structures with morphologies such as nanowires (NWs

pH-driven enhancement of anti-tubercular drug loading on iron oxide nanoparticles for drug delivery in macrophages

• Karishma Berta Cotta,
• Sarika Mehra and
• Rajdip Bandyopadhyaya

Beilstein J. Nanotechnol. 2021, 12, 1127–1139, doi:10.3762/bjnano.12.84

• ]. Furthermore, their interaction with IONPs may be via carboxylate groups, amine groups or by neither [27]. pH variations thus can play a key role in promoting interactions between amino acids and metal oxide surfaces [29]. NOR has also been reported to form stable complexes with Fe2+/3+ [22]. It was also

Assessment of the optical and electrical properties of light-emitting diodes containing carbon-based nanostructures and plasmonic nanoparticles: a review

• Keshav Nagpal,
• Erwan Rauwel,
• Frédérique Ducroquet and
• Protima Rauwel

Beilstein J. Nanotechnol. 2021, 12, 1078–1092, doi:10.3762/bjnano.12.80

• , the device with 2–3% Ag-doped ZnO EIL shows maximum luminance of 10982 cd/m2, maximum current efficiency of 41.0 cd/A, and EQE of 15.2%. The addition of AgNP to PBD-based ETL enhances the green emission [75]. Kandulna et al. have addressed the effect of plasmonic NP on hybrid metal oxide–polymer

• enhanced through the SPR effect of AgNP, which in turn could counteract the high external luminance. Thus, the low brightness and short operation lifetime of blue QLED could be improved by using CNT–polymer or CNT–metal oxide nanocomposites as ETL and incorporating AgNP in this layer. Further strategies to

• , and maximum luminance of various LED with carbon nanostructures, plasmonic, and metal oxide NP in the device layers. Funding This research has been supported by the European Regional Development Fund project EQUiTANT TK134 (F180175TIBT) and EMÜ bridge funding P200030TIBT.

Progress and innovation of nanostructured sulfur cathodes and metal-free anodes for room-temperature Na–S batteries

• Marina Tabuyo-Martínez,
• Bernd Wicklein and
• Pilar Aranda

Beilstein J. Nanotechnol. 2021, 12, 995–1020, doi:10.3762/bjnano.12.75

• 10 A·g−1) [49]. Metallic and metal oxide compounds have also attracted much interest due to their electronic conductivity and their high polarity, which leads to strong chemical interaction with polysulfides. For instance, Yan et al. [50] reported an electrode with an excellent performance that is

Molecular assemblies on surfaces: towards physical and electronic decoupling of organic molecules

• Sabine Maier and
• Meike Stöhr

Beilstein J. Nanotechnol. 2021, 12, 950–956, doi:10.3762/bjnano.12.71

• the substituents of the pyrenes derivatives [87]. Metal oxide thin films on top of metal substrates are another interesting class of ultrathin interfacial layers to decouple organic molecules and to enable the study of their electronic properties without the contribution of the underlying metal

• molecular conformation by planarizing the carbon backbone as well as the self-assembly. Hurdax et al. [89] suggested that work function measurements before and after the adsorption of molecules should give insight into the electronic and physical decoupling. It should be noted that metal oxide thin films

The role of deep eutectic solvents and carrageenan in synthesizing biocompatible anisotropic metal nanoparticles

• Nabojit Das,
• Akash Kumar and
• Raja Gopal Rayavarapu

Beilstein J. Nanotechnol. 2021, 12, 924–938, doi:10.3762/bjnano.12.69

• the principles of green chemistry. Despite extensive studies for more than a decade, DESs as solvents for nanomaterial synthesis yet awaits exploration regarding biological applications. In an interesting recently published work, a natural deep eutectic solvent (NADES) has been used to extract metal

• oxide nanoparticles [28]. Numerous indispensable parameters including surface tension, polarity, viscosity, and hydrogen bonding have an important influence on the reactivity of species. Also, the formation of nanostructures is governed by the mass transport properties of the DES components. It is also

Nanogenerator-based self-powered sensors for data collection

• Yicheng Shao,
• Maoliang Shen,
• Yuankai Zhou,
• Xin Cui,
• Lijie Li and
• Yan Zhang

Beilstein J. Nanotechnol. 2021, 12, 680–693, doi:10.3762/bjnano.12.54

• largely influenced by the surface carrier density on the surface of the nanowires. The adsorption of gas molecules can change the surface carrier density by the shielding effect, so the output of the sensor is very sensitive to the gas concentration. Compared with traditional metal oxide semiconductor

Influence of electrospray deposition on C₆₀ molecular assemblies

• Antoine Hinaut,
• Sebastian Scherb,
• Sara Freund,
• Zhao Liu,
• Thilo Glatzel and
• Ernst Meyer

Beilstein J. Nanotechnol. 2021, 12, 552–558, doi:10.3762/bjnano.12.45

• different surfaces and compare, for sub-monolayer coverages, the influence of the deposition method on the formation of molecular assemblies. Whereas the island location is the main difference for metal surfaces, we observe for alkali halide and metal oxide substrates that the high-vacuum electrospray

• ][25][28] and metal oxide semiconductors [23][24], while large three-dimensional molecular islands or clusters have been revealed on ionic crystals or bulk insulators [22][26][27][29]. Most of the studies have been performed after thermal evaporation (TE) of C60 from a crucible, but C60 is also one of

• used as model surface in nc-AFM measurements [31][32][33][34], and, finally, NiO(001), a p-type wide-bandgap metal oxide with potential applications in photovoltaics [35][36][37]. For all cases, we show the typical C60 structures formed by TE and compare these with the results from HV-ESD. This allows

The preparation temperature influences the physicochemical nature and activity of nanoceria

• Robert A. Yokel,
• Wendel Wohlleben,
• Johannes Georg Keller,
• Matthew L. Hancock,
• Jason M. Unrine,
• D. Allan Butterfield and
• Eric A. Grulke

Beilstein J. Nanotechnol. 2021, 12, 525–540, doi:10.3762/bjnano.12.43

• family of metal oxide ENMs used industrially, as catalysts in diesel fuel, abrasives in chemical mechanical planarization, in integrated circuit manufacture, as structural supports for catalysts for fuel synthesis applications, in solid oxide fuel cells, and in rechargeable batteries [1][2]. Cerium oxide

Solution combustion synthesis of a nanometer-scale Co₃O₄ anode material for Li-ion batteries

• Monika Michalska,
• Huajun Xu,
• Qingmin Shan,
• Shiqiang Zhang,
• Yohan Dall'Agnese,
• Yu Gao,
• Amrita Jain and
• Marcin Krajewski

Beilstein J. Nanotechnol. 2021, 12, 424–431, doi:10.3762/bjnano.12.34

• current densities between 50 and 5000 mA·g−1. Keywords: anode material; cobalt oxide; lithium-ion battery; solution combustion synthesis; transition metal oxide; Introduction Recently, a considerable research effort regarding new anode materials has been made because the traditional carbonaceous anodes

• −1 shows that the values of specific capacity consecutively rise over the theoretical capacity value and are maintained at 1060 mAh·g−1 after 100th cycle. This phenomenon is well known for different transition metal oxide electrodes and is usually ascribed to the reversible formation/dissolution of a

Nickel nanoparticle-decorated reduced graphene oxide/WO₃ nanocomposite – a promising candidate for gas sensing

• Ilka Simon,
• Alexandr Savitsky,
• Rolf Mülhaupt,
• Vladimir Pankov and
• Christoph Janiak

Beilstein J. Nanotechnol. 2021, 12, 343–353, doi:10.3762/bjnano.12.28

• ][9]. Metal oxide semiconductors (MOS) are the most commonly used gas sensors [10]. MOS can be divided into n-type and p-type MOS. In n-type MOS electrons are the majority charge carriers, while in p-type MOS holes are the majority charge carriers [6]. The exposure to reducing gases causes a decrease

• , and greater stability than pure WO3 [20]. WO3 decorated with palladium nanoparticles on the surface can be used as an improved and reusable gas sensor for NH3 [21]. Metal oxide semiconductor junctions can either be formed between two p-type MOS or two n-type MOS (p–p/n–n homojunctions) or between a p

• performance of MOS@rGO can further be improved by either chemical doping or by combination with a transition metal as ternary component [38]. Iron oxide-doped WO3 films showed improved NO2 sensing at room temperature, when adding a layer of 16 nm p-type rGO on the metal oxide film [39]. Nickel-doped SnO2

TiO_x/Pt₃Ti(111) surface-directed formation of electronically responsive supramolecular assemblies of tungsten oxide clusters

• Marco Moors,
• Yun An,
• Agnieszka Kuc and
• Kirill Yu. Monakhov

Beilstein J. Nanotechnol. 2021, 12, 203–212, doi:10.3762/bjnano.12.16

• of electronic devices appealing for the implementation in conceptually new data storage cells [1]. Specifically, resistive memories [2] based on the change of the electrical properties of a transition metal oxide thin layer, integrated in a simple electrode setup as a function of an externally

• significant points of focus for their integration into practical devices. In fact, the economically ideal way to obtain molecule-based devices would be the propensity of surface-deposited molecular metal-oxide clusters to self-assemble toward stable and reproducible functional supramolecular structures [8

• ]. One possibility to achieve this is to create substrate surfaces, whose characteristics would give rise to the nanostructured metal-oxide self-assembly formation. Herein, we demonstrate the potential of this approach using thermal evaporation of WO3 powder under ultra-high vacuum (UHV) on ultrathin

A review on the green and sustainable synthesis of silver nanoparticles and one-dimensional silver nanostructures

• Sina Kaabipour and
• Shohreh Hemmati

Beilstein J. Nanotechnol. 2021, 12, 102–136, doi:10.3762/bjnano.12.9

• [143][231]. In most cases, AgNPs are synthesized in metal oxide thin films such as TiO2, SiO2, and ZrO2 where the average particle size is almost 10 nm when the heating temperature is 600 °C in the case of SiO2 thin films, and 500 °C in the case of TiO2 and ZrO2 [231]. Arun Kumar et al. [145

• [232]. Organic solvents are generally more advantageous, as they can act as an oxygen-supplying agent for the metal oxide and result in more uniform structures and a smaller size distribution [232]. One important advantage of the sol–gel technique is the large freedom for choosing different precursors

• precursor for this purpose [241]. An important advantage of this technique is the establishment of a silver-metal-oxide (e.g. SiO2 or TiO2) nanocomposite coating using only one deposition step [241]. The CVD method also provides many opportunities for the synthesis of silver-coated materials with varying

ZnO and MXenes as electrode materials for supercapacitor devices

• Ameen Uddin Ammar,
• Ipek Deniz Yildirim,
• Feray Bakan and
• Emre Erdem

Beilstein J. Nanotechnol. 2021, 12, 49–57, doi:10.3762/bjnano.12.4

• supercapacitor device are important factors in this scenario. Nowadays, ZnO as metal oxide and MXene as 2D materials are the rising stars of electrode materials in supercapacitors due to their highly controllable properties. Therefore, we review the findings about ZnO and MXene in terms of defect structures and

• semiconductor metal oxide, here ZnO, is processed chemically or physically as an electrode. This is rather complicated and it is important which method is used to test the electrical properties. The common method is the three-point method in which the material is tested with a counter and a reference electrode

• Nyquist plot and the first semicircle of the Nyquist plot gives the resistance values. In general, defective and nanoscale ZnO has lower resistance values and the semicircle becomes more prominent, as depicted in Figure 1f. Metal oxide electrodes normally show resistive, rather than conductive, behavior

Free and partially encapsulated manganese ferrite nanoparticles in multiwall carbon nanotubes

• Saja Al-Khabouri,
• Salim Al-Harthi,
• Toru Maekawa,
• Mohamed E. Elzain,
• Ashraf Al-Hinai,
• Ahmed D. Al-Rawas,
• Abbsher M. Gismelseed,
• Ali A. Yousif and
• Myo Tay Zar Myint

Beilstein J. Nanotechnol. 2020, 11, 1891–1904, doi:10.3762/bjnano.11.170

• were attributed to an increase in the dipolar interparticle interactions due to the close packing of nanoparticles within the tubes [7]. There are several potential applications that use metal–metal oxide/CNTs hybrid systems. Carbon nanostructures decorated with titania and silica are used for the

• removal of harmful pollutants [8], carbon nanotubes decorated with molybdenum disulfide are used in microbial fuel cells [9] and photoelectric detectors [10], supercapacitor electrodes use binary metal oxide/multiwall carbon nanotubes (MWCNTs) [11], among other numerous recently developed applications [12

Unravelling the interfacial interaction in mesoporous SiO₂@nickel phyllosilicate/TiO₂ core–shell nanostructures for photocatalytic activity

• Bridget K. Mutuma,
• Xiluva Mathebula,
• Isaac Nongwe,
• Bonakele P. Mtolo,
• Boitumelo J. Matsoso,
• Rudolph Erasmus,
• Zikhona Tetana and
• Neil J. Coville

Beilstein J. Nanotechnol. 2020, 11, 1834–1846, doi:10.3762/bjnano.11.165

• metal oxides, such as ZrO2 [16] and SiO2 [17], influence the morphology and surface features of the resulting binary metal oxide semiconductors. Moreover, these binary metal oxide semiconductors act as charge-transfer catalysts and significantly reduce the electron–hole recombination [18][19]. Another

• surface [23]. Thus, silica-based core–shell nanocomposites offer added advantages of manipulating the pore structure, surface area, morphology, and catalyst reactivity [28]. Unlike the metal oxide–metal oxide composites, the use of metal oxide core@metal nanocomposites as dopants for titania

• @NiPS/TiO2 was higher with approx. 2.68 eV. Unlike other metal oxide binary systems where TiO2 is coated with SiO2 [68][69], in this study, the mSiO2@NiPS core–shell structure was coated with TiO2 nanoparticles, which readily absorb in the UV region. This suggests that the presence of TiO2 on the

Nanocasting synthesis of BiFeO₃ nanoparticles with enhanced visible-light photocatalytic activity

• Thomas Cadenbach,
• Maria J. Benitez,
• A. Lucia Morales,
• Cesar Costa Vera,
• Luis Lascano,
• Francisco Quiroz,
• Alexis Debut and
• Karla Vizuete

Beilstein J. Nanotechnol. 2020, 11, 1822–1833, doi:10.3762/bjnano.11.164

• photocatalytic activity [20]. Since the photocatalytic degradation of organic molecules using a metal oxide photocatalyst is a heterogeneous process, it is obvious that efficiency and overall catalytic performance are strongly correlated to the number of active sites on the catalyst surface area and, thus, to

• synthesize metal oxide particles and, in particular, nanometer-sized ferrite particles due to their availability, low cost and relative inertness [36][37][38][39][40][41]. In the present work, we show the synthesis of pure-phase BiFeO3 nanoparticles with a particle diameter of 5.5 ± 1.0 nm by a wet

Mapping of integrated PIN diodes with a 3D architecture by scanning microwave impedance microscopy and dynamic spectroscopy

• Rosine Coq Germanicus,
• Peter De Wolf,
• Florent Lallemand,
• Catherine Bunel,
• Serge Bardy,
• Hugues Murray and
• Ulrike Lüders

Beilstein J. Nanotechnol. 2020, 11, 1764–1775, doi:10.3762/bjnano.11.159

• , determined by our analytic procedure [32], as a function of VDC for both n- and p-type semiconductor materials. Using the complete metal–oxide–semiconductor equations, the Poisson–Boltzmann equation is solved for various active dopant concentration values ranging from 1015 to 1019 atoms·cm−3. In the sMIM

Direct observation of the Si(110)-(16×2) surface reconstruction by atomic force microscopy

• Tatsuya Yamamoto,
• Ryo Izumi,
• Kazushi Miki,
• Takahiro Yamasaki,
• Yasuhiro Sugawara and
• Yan Jun Li

Beilstein J. Nanotechnol. 2020, 11, 1750–1756, doi:10.3762/bjnano.11.157

• high-performance metal–oxide–semiconductor field-effect transistors (p-MOSFETs) [1][2] because the hole mobility of Si(110) is twice that of the other Si planes [3]. For surface science research, Si(110) has been used as a template substrate for self-assembled nanowires [4][5][6], nanomeshes [7], and

Oxidation of Au/Ag films by oxygen plasma: phase separation and generation of nanoporosity

• Abdel-Aziz El Mel,
• Said A. Mansour,
• Mujaheed Pasha,
• Atef Zekri,
• Janarthanan Ponraj,
• Akshath Shetty and
• Yousef Haik

Beilstein J. Nanotechnol. 2020, 11, 1608–1614, doi:10.3762/bjnano.11.143

• film can be explained by the Kirkendall effect [24]. More precisely, as silver diffuses out of the alloy film, vacancies are injected into the metal/oxide interface and migrate within the fast-diffusing medium (represented here by the metal alloy in Figure 8c). As the oxidation process evolves

Cu₂O nanoparticles for the degradation of methyl parathion

• Juan Rizo,
• David Díaz,
• Benito Reyes-Trejo and
• M. Josefina Arellano-Jiménez

Beilstein J. Nanotechnol. 2020, 11, 1546–1555, doi:10.3762/bjnano.11.137

• alkaline in aqueous medium. Thus, Cu2O is a basic metal oxide. Similarly, as the NP size decreases the surface-to-volume ratio increases. A higher surface area implies a higher amount of hydroxy groups [47][48] and, hence, a higher basicity. MP degradation can be further extended to different metal oxides