9.1% efficient zinc oxide/silicon solar cells on a 50 μm thick Si absorber

• Rafal Pietruszka,
• Bartlomiej S. Witkowski,
• Monika Ozga,
• Katarzyna Gwozdz,
• Ewa Placzek-Popko and
• Marek Godlewski

Beilstein J. Nanotechnol. 2021, 12, 766–774, doi:10.3762/bjnano.12.60

• inexpensive alternatives for indium tin oxide (ITO) [9]. In this work, we used ALD to deposit zinc oxide nanoseeds, magnesium-doped zinc oxide (MZO) layers and aluminium-doped zinc oxide films. We thus continue our interest on photovoltaic structures based on thin films of ZnO. Recently, there have been

A review of defect engineering, ion implantation, and nanofabrication using the helium ion microscope

• Frances I. Allen

Beilstein J. Nanotechnol. 2021, 12, 633–664, doi:10.3762/bjnano.12.52

High-yield synthesis of silver nanowires for transparent conducting PET films

• Gul Naz,
• Hafsa Asghar,
• Muhammad Ramzan,
• Muhammad Arshad,
• Rashid Ahmed,
• Muhammad Bilal Tahir,
• Bakhtiar Ul Haq,
• Nadeem Baig and
• Junaid Jalil

Beilstein J. Nanotechnol. 2021, 12, 624–632, doi:10.3762/bjnano.12.51

• flexibility after the ink coating. The maximum transmittance value of as-prepared PET films in the visible region was estimated to be about 92.5% with a sheet resistance value of ca. 20 Ω/sq. This makes the films a potential substitute to commonly used expensive indium tin oxide (ITO) in the field of flexible

• electrodes made of sputtered indium tin oxide (ITO) films [1][2][3]. These films are widely used because of their high transmittance, low sheet resistance, and high electrical conductivity. Yet, they still have some major drawbacks such as high cost, intrinsic brittleness due to the ceramic nature [4], and

Boosting of photocatalytic hydrogen evolution via chlorine doping of polymeric carbon nitride

• Malgorzata Aleksandrzak,
• Michalina Kijaczko,
• Wojciech Kukulka,
• Daria Baranowska,
• Martyna Baca,
• Beata Zielinska and
• Ewa Mijowska

Beilstein J. Nanotechnol. 2021, 12, 473–484, doi:10.3762/bjnano.12.38

• potentiostat in a three-electrode test cell with a platinum wire as the counter electrode and the saturated calomel electrode (SCE) as the reference. The working electrode was a fluorine-doped tin oxide (FTO) glass with the analyzed material drop-casted from a 0.2% ethanol/Nafion solution. A 0.5 M sodium

Solution combustion synthesis of a nanometer-scale Co₃O₄ anode material for Li-ion batteries

• Monika Michalska,
• Huajun Xu,
• Qingmin Shan,
• Shiqiang Zhang,
• Yohan Dall'Agnese,
• Yu Gao,
• Amrita Jain and
• Marcin Krajewski

Beilstein J. Nanotechnol. 2021, 12, 424–431, doi:10.3762/bjnano.12.34

• sites). Crystalline Co3O4 exhibits the space group Fd3m (227) [5]. It also can reversibly store eight lithium ions according to the following conversion reaction: This redox reaction corresponds to a theoretical capacity of about 890 mAh·g−1 [1][2][3][4]. However, similarly to silicon and tin materials

A review on the green and sustainable synthesis of silver nanoparticles and one-dimensional silver nanostructures

• Sina Kaabipour and
• Shohreh Hemmati

Beilstein J. Nanotechnol. 2021, 12, 102–136, doi:10.3762/bjnano.12.9

• rheological additives [103]. AgNW-coated conductive films have been considered as a promising alternative over conventional indium tin oxide (ITO)-coated conductive films [89]. The synthesis of silver nanostructures, and generally all types of nanostructures, can be categorized as one of two approaches [104

Fusion of purple membranes triggered by immobilization on carbon nanomembranes

• René Riedel,
• Natalie Frese,
• Fang Yang,
• Martin Wortmann,
• Raphael Dalpke,
• Daniel Rhinow,
• Norbert Hampp and
• Armin Gölzhäuser

Beilstein J. Nanotechnol. 2021, 12, 93–101, doi:10.3762/bjnano.12.8

• consisting of the CNM substrate as the upper and an indium tin oxide (ITO) as the lower capacitor plate. A sample drop was placed between the two electrodes. For electrostatic experiments (drop was in contact with substrate plate only) the plate separation distance was held constant at 10 mm, while it was

• Figure 1c–f, an electrical field was applied to the drop. The substrate itself served as a positively charged capacitor plate whereas the negatively charged plate consisted of indium tin oxide. As the electric field is attenuated in areas that have already been covered by PM patches, subsequently

ZnO and MXenes as electrode materials for supercapacitor devices

• Ameen Uddin Ammar,
• Ipek Deniz Yildirim,
• Feray Bakan and
• Emre Erdem

Beilstein J. Nanotechnol. 2021, 12, 49–57, doi:10.3762/bjnano.12.4

• used, for example, in water purification, as electrochemical actuators, as transparent conductive electrodes, and as biosensors [21][22][28]. To enhance the performance of MXene supercapacitors, a variety of materials, such as graphene and carbon nanotubes (CNTs), tin(IV) oxide (SnO2), and iron(III

Atomic layer deposited films of Al₂O₃ on fluorine-doped tin oxide electrodes: stability and barrier properties

• Hana Krýsová,
• Michael Neumann-Spallart,
• Hana Tarábková,
• Pavel Janda,
• Ladislav Kavan and
• Josef Krýsa

Beilstein J. Nanotechnol. 2021, 12, 24–34, doi:10.3762/bjnano.12.2

• , Technická 5, 166 28 Prague 6, Czech Republic 10.3762/bjnano.12.2 Abstract Al2O3 layers were deposited onto electrodes by atomic layer deposition. Solubility and electron-transport blocking were tested. Films deposited onto fluorine-doped tin oxide (FTO, F:SnO2/glass) substrates blocked electron transfer to

• alumina coatings was ascribed to its capability of passivating semiconductor/electrolyte interfaces, thus reducing photogenerated charge-carrier recombination (e.g., on BiVO4 [16]). In this work, Al2O3 films were deposited via ALD on thermally grown SiO2 on silicon or on fluorine-doped tin oxide (FTO

• grade. 0.1 M sodium phosphate buffer solution, pH 7.2, was obtained from Fluka. Triply distilled water was used for the preparation of solutions. Fluorine-doped tin oxide-coated 2 mm thick glass (TEC-7, 7 Ω/□, Sigma-Aldrich), was ultrasonically pre-cleaned with isopropanol, treated with acetone, ethanol

Piezotronic effect in AlGaN/AlN/GaN heterojunction nanowires used as a flexible strain sensor

• Jianqi Dong,
• Liang Chen,
• Yuqing Yang and
• Xingfu Wang

Beilstein J. Nanotechnol. 2020, 11, 1847–1853, doi:10.3762/bjnano.11.166

• synthesize AlGaN/AlN/GaN heterojunction NWs with controllable size. A single NW is transferred to a flexible poly(ethylene terephthalate) substrate and fixed by indium tin oxide electrodes to form an ohmic contact for the strain sensor. An external mechanical stress is introduced to study the performance of

• (EC) wet etching, to prepare AlGaN/AlN/GaN heterojunction NWs with a controllable size. After the lift-off, a single NW is transferred to a flexible poly(ethylene terephthalate) (PET) substrate and is fixed by indium tin oxide (ITO) electrodes to form an ohmic contact for the strain sensor. Under

Amorphized length and variability in phase-change memory line cells

• Nafisa Noor,
• Sadid Muneer,
• Raihan Sayeed Khan,
• Anna Gorbenko and
• Helena Silva

Beilstein J. Nanotechnol. 2020, 11, 1644–1654, doi:10.3762/bjnano.11.147

• -switching process and not to the permanent and detrimental electrical breakdown failure that occurs in any dielectric material. Experimental The patterned GST-225 line cells used for this study were deposited on silicon dioxide (SiO2), had bottom metal contact pads (tungsten with Ti/TiN liner), and were

Triboelectric nanogenerator based on Teflon/vitamin B1 powder for self-powered humidity sensing

• Liangyi Zhang,
• Huan Li,
• Yiyuan Xie,
• Jing Guo and
• Zhiyuan Zhu

Beilstein J. Nanotechnol. 2020, 11, 1394–1401, doi:10.3762/bjnano.11.123

• -free humidity sensors by using biocompatible collagen nanofibrils [43]. More recently, Zhang et al. developed a TENG-driven self-powered flexible humidity sensor based on a tin disulfide nanoflower/reduced graphene oxide (SnS2/rGO) hybrid nanomaterial [44]. However, the large-scale application of TENGs

Analysis of catalyst surface wetting: the early stage of epitaxial germanium nanowire growth

• Owen C. Ernst,
• Felix Lange,
• David Uebel,
• Thomas Teubner and
• Torsten Boeck

Beilstein J. Nanotechnol. 2020, 11, 1371–1380, doi:10.3762/bjnano.11.121

• chalcopyrites [11], or precursors for complex structures, such as nanowires [12]. Silicon, germanium and silicon oxide nanowires, for example, can be formed on different substrates by using metal catalysts in the form of tin, indium or gold nanodroplets [13][14][15]. Such nanometre-sized one-dimensional

Structural and electronic properties of SnO₂ doped with non-metal elements

• Jianyuan Yu,
• Yingeng Wang,
• Yan Huang,
• Xiuwen Wang,
• Jing Guo,
• Jingkai Yang and
• Hongli Zhao

Beilstein J. Nanotechnol. 2020, 11, 1321–1328, doi:10.3762/bjnano.11.116

• research works has been done examining different doping elements. Doped tin oxide thin film have been widely used in the fields of thin film solar cell electrodes, electronic display devices, and gas sensors. Also doped SnO2 been used for energy-saving low-emissivity glass coatings due to low resistivity

• of a non-metal atom replacing an O atom in a SnO2 unit cell (The red spheres are oxygen atoms, the gray spheres are tin atoms, and the light blue sphere is the non-metal atom). Energy band structure, total density of states and partial density of states of SnO2 doped with non-metal atoms: (a) SnO2/B

Transition from freestanding SnO₂ nanowires to laterally aligned nanowires with a simulation-based experimental design

• Jasmin-Clara Bürger,
• Sebastian Gutsch and
• Margit Zacharias

Beilstein J. Nanotechnol. 2020, 11, 843–853, doi:10.3762/bjnano.11.69

• laterally aligned nanowires, indicating that the nanowire growth takes place in a transient period of the gas exchange. Keywords: finite element method simulation; laterally aligned nanowires; planar growth; tin oxide; vapor–liquid–solid nanowire growth; Introduction Since the first reports in 1964 by

• result, Choi et al. were able to measure an improved sensitivity for gas sensors made of tin oxide nanowires (SnO2 NWs) in comparison with powder-based SnO2 thin films [9]. For the use of NWs in electronic and sensor devices, freestanding NWs often have to be scratched off of the growth substrate

• ]. The droplets compete for the tin atoms and oxygen molecules [30]. This results in a locally reduced material concentration in the surrounding area of the catalyst-decorated samples. As seen from the simulations of the volumetric flow (Figure 2), an increased volumetric flow will result in a reduced

Adsorption behavior of tin phthalocyanine onto the (110) face of rutile TiO₂

• Lukasz Bodek,
• Mads Engelund,
• Aleksandra Cebrat and
• Bartosz Such

Beilstein J. Nanotechnol. 2020, 11, 821–828, doi:10.3762/bjnano.11.67

• , Swiss Federal Laboratories for Materials Science and Technology, Überlandstrasse 129, 8600 Dübendorf, Switzerland 10.3762/bjnano.11.67 Abstract The adsorption behavior of tin phthalocyanine (SnPc) molecules on rutile TiO2(110) was studied by scanning tunneling microscopy (STM). Low-temperature STM

• measurements of single molecules reveal the coexistence of two conformations of molecules on the TiO2 surface. Density functional theory-based simulations (DFT) indicate that the difference originates from the position of the tin atom protruding from the molecule plane. The irreversible switching of Sn-up

• tunneling microscopy (STM); tin phthalocyanine (SnPc); titanium dioxide (TiO2); Introduction Phthalocyanines (Pcs) are aromatic molecules that can form metal complexes with a variety of elements, which can be used to tune molecular properties, such as position or shape of adsorption bands. Therefore, Pcs

Hexagonal boron nitride: a review of the emerging material platform for single-photon sources and the spin–photon interface

• Stefania Castelletto,
• Faraz A. Inam,
• Shin-ichiro Sato and
• Alberto Boretti

Beilstein J. Nanotechnol. 2020, 11, 740–769, doi:10.3762/bjnano.11.61

Structural optical and electrical properties of a transparent conductive ITO/Al–Ag/ITO multilayer contact

• Aliyu Kabiru Isiyaku,
• Ahmad Hadi Ali and
• Nafarizal Nayan

Beilstein J. Nanotechnol. 2020, 11, 695–702, doi:10.3762/bjnano.11.57

• Science, Kaduna State University, P.M.B 2339, Kaduna State, Nigeria Microelectronic and Nanotechnology Shamsuddin Research Centre (MiNT-SRC), Universiti Tun Hussein Onn Malaysia, 86400 Parit Raja, Batu Pahat, Johor, Malaysia 10.3762/bjnano.11.57 Abstract Indium tin oxide (ITO) is a widely used material

• × 10−3 Ω−1). These highly conductive and transparent ITO films with Al–Ag interlayer can be a promising contact for low-resistance optoelectronics devices. Keywords: annealing; DC sputtering; figure of merit; indium tin oxide (ITO); multilayer structure; RF sputtering; Introduction Transparent

• conducting oxides (TCO) thin films have been receiving much attention regarding their use as contacts in several optoelectronic devices such as LEDs [1], solar cells [2] and flat panel displays [3]. Indium tin oxide (ITO) is the most commonly used TCO for industrial and laboratory applications due to its

Implementation of data-cube pump–probe KPFM on organic solar cells

• Benjamin Grévin,
• Olivier Bardagot and
• Renaud Demadrille

Beilstein J. Nanotechnol. 2020, 11, 323–337, doi:10.3762/bjnano.11.24

• levels of holes and electrons upon illumination, symbolized by dotted lines. (b) Organic BHJ solar cell and experimental configuration. The sample is illuminated in backside geometry. The transparent anode, the hole collecting electrode made of indium tin oxide coated with PEDOT:PSS, is grounded. The

Semitransparent Sb₂S₃ thin film solar cells by ultrasonic spray pyrolysis for use in solar windows

• Jako S. Eensalu,
• Atanas Katerski,
• Erki Kärber,
• Lothar Weinhardt,
• Monika Blum,
• Clemens Heske,
• Wanli Yang,
• Ilona Oja Acik and
• Malle Krunks

Beilstein J. Nanotechnol. 2019, 10, 2396–2409, doi:10.3762/bjnano.10.230

• chemical methods [20]. Until now, semitransparency aspects of Sb2S3 solar cells have only been studied by Zimmermann et al., who reported a PCE of 4.25% for a tin-doped indium oxide (ITO)/TiO2/Sb2S3/poly(3-hexylthiophene-2,5-diyl) (P3HT)/Ag solar cell with a 50–70 nm thick Sb2S3 absorber and a

Polyvinylpyrrolidone as additive for perovskite solar cells with water and isopropanol as solvents

• Chen Du,
• Shuo Wang,
• Xu Miao,
• Wenhai Sun,
• Yu Zhu,
• Chengyan Wang and
• Ruixin Ma

Beilstein J. Nanotechnol. 2019, 10, 2374–2382, doi:10.3762/bjnano.10.228

• cell (iPSC), Pengcheng Zhou et al. managed to achieve a signifanct boost in efficiency [30]. The photovoltaic properties of inverted polymer solar cells using a PVP-modified indium tin oxide (ITO) layer as the electron-collecting electrode were reported on by J. W. Shim and co-workers [31]. In this

Nontoxic pyrite iron sulfide nanocrystals as second electron acceptor in PTB7:PC₇₁BM-based organic photovoltaic cells

• Olivia Amargós-Reyes,
• José-Luis Maldonado,
• Omar Martínez-Alvarez,
• María-Elena Nicho,
• José Santos-Cruz,
• Juan Nicasio-Collazo,
• Irving Caballero-Quintana and
• Concepción Arenas-Arrocena

Beilstein J. Nanotechnol. 2019, 10, 2238–2250, doi:10.3762/bjnano.10.216

• and synthesis of FeS2 nanocrystals All chemicals were used as received without further purification. For FeS2 synthesis, iron(II) chloride, octadecylamine and diphenyl ether were acquired from Sigma-Aldrich. For OPV fabrication, indium tin oxide (ITO) covered glass substrates (10 Ω/sq, ≈165 nm

• :PC71BM:FeS2/PFN/Field’s metal (FM) fabrication The OPV devices were fabricated as follows (Figure 1a): Indium tin oxide (ITO) covered glass substrates were cut (≈1.8 cm × 1.8 cm) and ultrasonically cleaned sequentially for about 20 min in a detergent solution, distilled water and ethanol and dried in an oven

Mannosylated brush copolymers based on poly(ethylene glycol) and poly(ε-caprolactone) as multivalent lectin-binding nanomaterials

• Stefania Ordanini,
• Wanda Celentano,
• Anna Bernardi and
• Francesco Cellesi

Beilstein J. Nanotechnol. 2019, 10, 2192–2206, doi:10.3762/bjnano.10.212

• examined. Results and Discussion Synthesis of the PCL-based macromonomer Propargyl-poly(ε-caprolactone)-methacrylate (Pg-PCL-MA) was prepared in two steps starting from ε-caprolactone, through a bulk ROP initiated by propargyl alcohol and catalyzed by tin(II) 2-ethylhexanoate [25] (Scheme 1, step a

• -poly(ε-caprolactone) (Pg-PCL). Pg-PCL was synthesized as reported in a previous work [25]. Briefly, ε-caprolactone (20 g, 0.175 mol, 5 equiv) was added in a round flask and heated up to 130 °C. A second yellowish solution containing propargyl alcohol (2.04 mL, 0.035 mol, 1 equiv) and tin(II) 2

Materials nanoarchitectonics at two-dimensional liquid interfaces

• Katsuhiko Ariga,
• Michio Matsumoto,
• Taizo Mori and
• Lok Kumar Shrestha

Beilstein J. Nanotechnol. 2019, 10, 1559–1587, doi:10.3762/bjnano.10.153

• confirmed by steady-state optical spectroscopy. Photovoltaic cells with one-dimensional C60 nanorods as active layer sandwiched by an indium tin oxide anode and an aluminium cathode exhibited enhanced photovoltaic capabilities. It also led to a significant enhancement of photogenerated charge carriers as

Rapid thermal annealing for high-quality ITO thin films deposited by radio-frequency magnetron sputtering

• Petronela Prepelita,
• Ionel Stavarache,
• Doina Craciun,
• Florin Garoi,
• Catalin Negrila,
• Beatrice Gabriela Sbarcea and
• Valentin Craciun

Beilstein J. Nanotechnol. 2019, 10, 1511–1522, doi:10.3762/bjnano.10.149

• , P.O. Box MG-7, Magurele 077125, Ilfov, Romania ICPE-CA, Splaiul Unirii 313, Sector 3, 74204, Bucharest, Romania Dentix MILLENNIUM SRL, Sabareni-Ilfov, Romania 10.3762/bjnano.10.149 Abstract In this work, rapid thermal annealing (RTA) was applied to indium tin oxide (ITO) films in ambient atmosphere

• treatment on the ITO chemical composition. Using a Tauc plot, values of the optical band gap ranging from 3.17 to 3.67 eV were estimated. These values depend on the heat treatment and the thickness of the sample. Highly conductive indium tin oxide thin films (ρ = 7.4 × 10−5 Ω cm) were obtained after RTA

• treatment in an open atmosphere. Such films could be used to manufacture transparent contact electrodes for solar cells. Keywords: conductive transparent electrodes; indium tin oxide (ITO) films; optical properties; radio-frequency magnetron sputtering (rfMS); rapid thermal annealing (RTA); Introduction