Orally administered docetaxel-loaded chitosan-decorated cationic PLGA nanoparticles for intestinal tumors: formulation, comprehensive in vitro characterization, and release kinetics

• Sedat Ünal,
• Osman Doğan and
• Yeşim Aktaş

Beilstein J. Nanotechnol. 2022, 13, 1393–1407, doi:10.3762/bjnano.13.115

• seeded onto the apical side of 12-well polycarbonate membrane filters at a density of 60,000 cells/insert (Thincerts™, pore diameter 1 μm, area 1.13 cm2). The inserts were loaded with 500 µL of medium for the apical side and 1000 µL of medium for the basolateral side of the wells. Media were replaced

Roll-to-roll fabrication of superhydrophobic pads covered with nanofur for the efficient clean-up of oil spills

• Patrick Weiser,
• Robin Kietz,
• Marc Schneider,
• Matthias Worgull and
• Hendrik Hölscher

Beilstein J. Nanotechnol. 2022, 13, 1228–1239, doi:10.3762/bjnano.13.102

• (PE), and polycarbonate (PC), we obtained the best results by sandblasting the roller first with 0.8–1.2 mm cast iron particles and subsequently with white corundum with a particle size of 53–75 µm. For polylactide (PLA), smaller corundum particles with a size of 8–10 µm had to be used for the second

Micro- and nanotechnology in biomedical engineering for cartilage tissue regeneration in osteoarthritis

• Zahra Nabizadeh,
• Mahmoud Nasrollahzadeh,
• Hamed Daemi,
• Mohamadreza Baghaban Eslaminejad,
• Ali Akbar Shabani,
• Mehdi Dadashpour,
• Majid Mirmohammadkhani and
• Davood Nasrabadi

Beilstein J. Nanotechnol. 2022, 13, 363–389, doi:10.3762/bjnano.13.31

• actuators with tunable linear contractile actuation and cardiac pumping ability (Figure 4). This unique property of CNTs was also used to improve the functions of chondrocytes encapsulated in a polycarbonate urethane nanocomposite in which electrical stimulation led to enhanced cell densities [133]. CNTs

A photonic crystal material for the online detection of nonpolar hydrocarbon vapors

• Evgenii S. Bolshakov,
• Aleksander V. Ivanov,
• Andrei A. Kozlov,
• Anton S. Aksenov,
• Elena V. Isanbaeva,
• Sergei E. Kushnir,
• Aleksei D. Yapryntsev,
• Aleksander E. Baranchikov and
• Yury A. Zolotov

Beilstein J. Nanotechnol. 2022, 13, 127–136, doi:10.3762/bjnano.13.9

• converter. The SEM images have been obtained at the Centre of Shared Equipment of IGIC RAS. Sensors A composite sensor based on 3D PhC, which has a sandwich design, has been used for the experiments. The opal structure is formed on a glass or polymer (polycarbonate or polyethylene terephthalate) substrate

• recorded through the optically transparent carrier. A negligible reflection of the polycarbonate substrate is in the blue spectrum region (below 420 nm) and does not overlap with the reflection of the photonic crystal. As a result of the experiment, we obtained spectra measured at a predetermined time

Nanoscale friction and wear of a polymer coated with graphene

• Robin Vacher and
• Astrid S. de Wijn

Beilstein J. Nanotechnol. 2022, 13, 63–73, doi:10.3762/bjnano.13.4

• -lubricating material [24]. Saravanan et al. [25] have measured the friction and wear of polymer materials such as polyethylene, polycarbonate, polyoxymethylene, polymethyl methacrylate, polyetheretherketone, and polytetrafluoroethylene [26]. Polymer balls have been rubbed on a steel surface covered with

The role of deep eutectic solvents and carrageenan in synthesizing biocompatible anisotropic metal nanoparticles

• Nabojit Das,
• Akash Kumar and
• Raja Gopal Rayavarapu

Beilstein J. Nanotechnol. 2021, 12, 924–938, doi:10.3762/bjnano.12.69

• maintaining high yield and monodispersity. Initially, gold nanorods were synthesized using electrochemical methods using polycarbonate membrane templates or porous alumina for shape control in the presence of surfactants (mostly CTAB) [34][35]. Because of their optical properties, gold nanorods became

Fate and transformation of silver nanoparticles in different biological conditions

• Barbara Pem,
• Marija Ćurlin,
• Darija Domazet Jurašin,
• Valerije Vrček,
• Rinea Barbir,
• Vedran Micek,
• Raluca M. Fratila,
• Jesus M. de la Fuente and
• Ivana Vinković Vrček

Beilstein J. Nanotechnol. 2021, 12, 665–679, doi:10.3762/bjnano.12.53

• Unit for Laboratory Animals, at the Institute for Medical Research and Occupational Health, Zagreb, Croatia. The animals were kept under specific pathogen-free conditions, in polycarbonate cages with temperature (23 ± 2 °C) and humidity (55 ± 7%) control, with a 12 h light/dark reversed cycle. They

A review on the green and sustainable synthesis of silver nanoparticles and one-dimensional silver nanostructures

• Sina Kaabipour and
• Shohreh Hemmati

Beilstein J. Nanotechnol. 2021, 12, 102–136, doi:10.3762/bjnano.12.9

• demonstrated unique electrical properties. AgNPs coated on polycarbonate substrates were previously used to increase the electrical conductivity of polycarbonate composites [79]. AgNPs have also demonstrated minimum or no adverse effects on mechanical strength when embedded in polymeric materials or composites

Bulk chemical composition contrast from attractive forces in AFM force spectroscopy

• Dorothee Silbernagl,
• Media Ghasem Zadeh Khorasani,
• Natalia Cano Murillo,
• Anna Maria Elert and
• Heinz Sturm

Beilstein J. Nanotechnol. 2021, 12, 58–71, doi:10.3762/bjnano.12.5

• independent measurement for the local chemical composition and hence a complete structure–property correlation can be obtained. A proof of concept is provided by two model samples comprised of (1) epoxy/polycarbonate and (2) epoxy/boehmite. The preparation of the model samples allowed for the assignment of

• analysis (mPCA) from a kr/Fattr diagram. A third sample comprised of (3) epoxy/polycarbonate/boehmite is measured by ImAFM. The measurement of a 2 × 2 µm cross section yields 128 × 128 force curves which are successfully evaluated by a kr/Fattr diagram and the nanoscopic heterogeneity of the sample is

• epoxy (brown) and polycarbonate (PC, blue) and the reference measurement of glass (grey) in the property domain. When comparing the histograms of kr with the histograms of Fattr it again becomes apparent that the distributions of values for PC and epoxy overlap in the case of kr, whereas, in the case of

Out-of-plane surface patterning by subsurface processing of polymer substrates with focused ion beams

• Serguei Chiriaev,
• Luciana Tavares,
• Vadzim Adashkevich,
• Arkadiusz J. Goszczak and
• Horst-Günter Rubahn

Beilstein J. Nanotechnol. 2020, 11, 1693–1703, doi:10.3762/bjnano.11.151

• of the polymer. Effects of subsurface and surface processes on the surface morphology have been studied for three polymer materials: poly(methyl methacrylate), polycarbonate, and polydimethylsiloxane, by using focused ion beam irradiation with He+, Ne+, and Ga+. Thin films of a Pt60Pd40 alloy and of

• pristine Au were used to compare the patterning of thin films with different microstructures. We show that the height of Pt60Pd40 thin films deposited onto poly(methyl methacrylate) and polycarbonate substrates can be patterned by He+ ion beams with ultrahigh precision (nanometers) while preserving in

• pathways for volatile radiolysis products to leave the irradiated material. We also investigate the possibility to pattern the surface of other polymer substrates, such as polycarbonate (PC) and polydimethylsiloxane (PDMS), by subsurface processing with He+ ions. The choice of materials for this work has

Hexagonal boron nitride: a review of the emerging material platform for single-photon sources and the spin–photon interface

• Stefania Castelletto,
• Faraz A. Inam,
• Shin-ichiro Sato and
• Alberto Boretti

Beilstein J. Nanotechnol. 2020, 11, 740–769, doi:10.3762/bjnano.11.61

Rational design of block copolymer self-assemblies in photodynamic therapy

• Maxime Demazeau,
• Laure Gibot,
• Anne-Françoise Mingotaud,
• Patricia Vicendo,
• Clément Roux and
• Barbara Lonetti

Beilstein J. Nanotechnol. 2020, 11, 180–212, doi:10.3762/bjnano.11.15

• expansion of the self-assemblies and a rapid release of the photosensitizer (Figure 5b) [76]. In an original approach, light-responsive self-immolative polymers [70][71] (Figure 5a) based on a polycarbonate backbone have been proposed. Here a photolabile o-nitrobenzyl group can be removed through a redox

Size effects of graphene nanoplatelets on the properties of high-density polyethylene nanocomposites: morphological, thermal, electrical, and mechanical characterization

• Tuba Evgin,
• Alpaslan Turgut,
• Georges Hamaoui,
• Zdenko Spitalsky,
• Nicolas Horny,
• Matej Micusik,
• Mihai Chirtoc,
• Mehmet Sarikanat and
• Maria Omastova

Beilstein J. Nanotechnol. 2020, 11, 167–179, doi:10.3762/bjnano.11.14

• size of GnPs is one of the most important factors, only few studies have investigated the size effect of GnPs on the properties of nanocomposites with various matrices, such as HDPE [13][14][15], polypropylene (PP) [8][9][16][17], epoxy [18][19][20], and polycarbonate (PC) [21] in the range of about

Bombesin receptor-targeted liposomes for enhanced delivery to lung cancer cells

• Mohammad J. Akbar,
• Pâmela C. Lukasewicz Ferreira,
• Melania Giorgetti,
• Leanne Stokes and
• Christopher J. Morris

Beilstein J. Nanotechnol. 2019, 10, 2553–2562, doi:10.3762/bjnano.10.246

• then heated to 55 °C and vortexed extensively to produce MLVs. Five cycles of freeze-thawing (dry ice-acetone followed by heating to 55 °C) were performed to produce reduce the lamellarity of the vesicles. Finally, lipid suspensions were extruded (21×) through polycarbonate membranes of 200 nm, 100 nm

Design of a nanostructured mucoadhesive system containing curcumin for buccal application: from physicochemical to biological aspects

• Sabrina Barbosa de Souza Ferreira,
• Gustavo Braga,
• Évelin Lemos Oliveira,
• Jéssica Bassi da Silva,
• Hélen Cássia Rosseto,
• Lidiane Vizioli de Castro Hoshino,
• Mauro Luciano Baesso,
• Wilker Caetano,
• Craig Murdoch,
• Helen Elizabeth Colley and
• Marcos Luciano Bruschi

Beilstein J. Nanotechnol. 2019, 10, 2304–2328, doi:10.3762/bjnano.10.222

• , considered as the required work necessary to overcome the attraction forces between the sample surface and the polycarbonate probe surface, is a desirable parameter for mucoadhesive preparations aimed at buccal applications. In this sense, a higher adhesion could implicate higher retention, and consequently

• observed for adhesiveness, which could provide evidence of adhesion. This parameter evaluates the interaction between the formulation and polycarbonate probe, where this lower specificity explains this result. Conversely, the detachment force method relates the interaction of C974P-hydroxyls and the mucin

Subsurface imaging of flexible circuits via contact resonance atomic force microscopy

• Wenting Wang,
• Chengfu Ma,
• Yuhang Chen,
• Lei Zheng,
• Huarong Liu and
• Jiaru Chu

Beilstein J. Nanotechnol. 2019, 10, 1636–1647, doi:10.3762/bjnano.10.159

• measurements on some of the probes after CR-AFM subsurface imaging experiments. The thicknesses of the bottom, middle and top layers were approximated from practical AFM measurements. Different layer materials were investigated including PMMA, high-density polyethylene (HDPE), polystyrene (PS), polycarbonate

Angle-dependent structural colors in a nanoscale-grating photonic crystal fabricated by reverse nanoimprint technology

• Xu Zheng,
• Qing Wang,
• Jinjin Luan,
• Yao Li,
• Ning Wang and
• Rui Zhang

Beilstein J. Nanotechnol. 2019, 10, 1211–1216, doi:10.3762/bjnano.10.120

• for applications of visual sensors. Experimental A polycarbonate (PC) master mould with period of 750 nm and height of 170 nm was fabricated through NIL. The polydimethylsiloxane (PDMS) and cross-linker were obtained from Sylgard 184 (Dow Corning, USA). The photonic crystal film with grating patterns

Commercial polycarbonate track-etched membranes as substrates for low-cost optical sensors

• Paula Martínez-Pérez and
• Jaime García-Rupérez

Beilstein J. Nanotechnol. 2019, 10, 677–683, doi:10.3762/bjnano.10.67

• the interaction between the optical field and the target substances, which boosts the sensitivity. In this work, we propose the use of a readily available mesoporous material for the development of such sensors: commercial polycarbonate track-etched membranes. In order to demonstrate their utility for

• experiments were performed by placing different concentrations of ethanol solution on the polycarbonate track-etched membranes. As a result, a sensitivity value of around 56 nm/RIU was obtained and the reusability of the substrate was demonstrated. These results pave the way for the development of optical

• porous sensors with such easily available mesoporous material. Keywords: chemical sensor; Fabry–Pérot interferometer; optical sensor; polycarbonate; track-etched membrane; Introduction Sensors are present in our daily life in order to detect and monitor chemical, biological and physical agents of

Magnetism and magnetoresistance of single Ni–Cu alloy nanowires

• Andreea Costas,
• Camelia Florica,
• Elena Matei,
• Maria Eugenia Toimil-Molares,
• Ionel Stavarache,
• Andrei Kuncser,
• Victor Kuncser and
• Ionut Enculescu

Beilstein J. Nanotechnol. 2018, 9, 2345–2355, doi:10.3762/bjnano.9.219

• University of Bucharest, Faculty of Physics, PO Box MG-11, 077125, Magurele-Bucharest, Romania 10.3762/bjnano.9.219 Abstract Arrays of magnetic Ni–Cu alloy nanowires with different compositions were prepared by a template-replication technique using electrochemical deposition into polycarbonate nanoporous

• . Consequently, the magnetic properties of such nanowires can be tuned in agreement with the foreseen applications. The templates used are usually nanoporous ion-track polycarbonate membranes [21] and anodic alumina membranes [22]. Both Ni–Cu alloys and Ni–Cu multilayers have been intensively studied as simple

• electrochemical replication, using as templates chemically etched polycarbonate membranes irradiated with swift heavy ions. Individual Ni–Cu alloy nanowires of different compositions have been contacted on interdigitated metallic electrodes by using electron beam lithography (EBL) and magnetoresistive

Preparation and morphology-dependent wettability of porous alumina membranes

• Dmitry L. Shimanovich,
• Alla I. Vorobjova,
• Daria I. Tishkevich,
• Alex V. Trukhanov,
• Maxim V. Zdorovets and
• Artem L. Kozlovskiy

Beilstein J. Nanotechnol. 2018, 9, 1423–1436, doi:10.3762/bjnano.9.135

• as templates. The disadvantages of polymer membranes include low chemical and thermal resistance and problems in regeneration. The maximum operating temperature of polycarbonate membranes is 450 K. PAA membranes in this respect are more preferable and have been intensively recently studied for use in

CdSe nanorod/TiO₂ nanoparticle heterojunctions with enhanced solar- and visible-light photocatalytic activity

• Fakher Laatar,
• Hatem Moussa,
• Halima Alem,
• Lavinia Balan,
• Emilien Girot,
• Ghouti Medjahdi,
• Hatem Ezzaouia and
• Raphaël Schneider

Beilstein J. Nanotechnol. 2017, 8, 2741–2752, doi:10.3762/bjnano.8.273

• simulated solar light source (light intensity = 5 mW/cm2). A polycarbonate filter was added for experiments conducted under visible light irradiation (light intensity = 10 mW/cm2). In a typical experiment, 50 mg of the CdSe/TiO2 composite were dispersed in 50 mL of aqueous solution of RhB (10 mg/L) in a 70

Preparation and characterization of polycarbonate/multiwalled carbon nanotube nanocomposites

• Claudio Larosa,
• Niranjan Patra,
• Marco Salerno,
• Lara Mikac,
• Remo Merijs Meri and
• Mile Ivanda

Beilstein J. Nanotechnol. 2017, 8, 2026–2031, doi:10.3762/bjnano.8.203

• , Latvia 10.3762/bjnano.8.203 Abstract A polymer nanocomposite was produced by ultrasonic-assisted dispersion of multiwalled carbon nanotubes (MWCNTs) in a polycarbonate matrix using p-xylene and dichloromethane as the solvents. The filler loading was varied from 1 to 3 wt % in order to examine the effect

• dispersed phase in the composite films, while TGA and DSC analysis of the nanocomposites revealed enhanced thermal stability and decreased crystallinity, respectively, as compared to the neat polymer. The proposed composites can find application in a number of everyday products where polycarbonate is the

• base polymer. Keywords: multiwalled carbon nanotubes; nanocomposites; polycarbonate; thermal analysis; vibrational spectroscopy; Introduction Polycarbonate (PC) is a polymer with remarkable mechanical and optical properties, broadly used for water bottles, monitor screens and aircraft interiors but

Evaluation of preparation methods for suspended nano-objects on substrates for dimensional measurements by atomic force microscopy

• Petra Fiala,
• Daniel Göhler,
• Benno Wessely,
• Michael Stintz,
• Giovanni Mattia Lazzerini and
• Andrew Yacoot

Beilstein J. Nanotechnol. 2017, 8, 1774–1785, doi:10.3762/bjnano.8.179

• of polycarbonate (pore size 30 nm and 50 nm, Sterlitech Corp, Kent, USA and 100 nm, Merck Millipore, Darmstadt, Germany) as well as on silicon wafers (crystal orientation <100>) and on silicon wafers (crystal orientation <100>) coated with silicon dioxide. SEM measurements were performed for all

Surface-enhanced Raman scattering of self-assembled thiol monolayers and supported lipid membranes on thin anodic porous alumina

• Marco Salerno,
• Amirreza Shayganpour,
• Barbara Salis and
• Silvia Dante

Beilstein J. Nanotechnol. 2017, 8, 74–81, doi:10.3762/bjnano.8.8

• , and put under a mild vacuum overnight to remove all solvent traces. POPC/POPS in a 9:1 mol/mol ratio and DOTAP were then re-suspended in PBS at a 5 g/L concentration, let to swell for 30 min, and extruded 11 times through a polycarbonate filter (Whatman, USA) with 100 nm pore diameter to form

Numerical investigation of depth profiling capabilities of helium and neon ions in ion microscopy

• Patrick Philipp,
• Lukasz Rzeznik and
• Tom Wirtz

Beilstein J. Nanotechnol. 2016, 7, 1749–1760, doi:10.3762/bjnano.7.168

• transistor-like switches, optical switches, and photodiodes. Cu implanted polycarbonate (PC) has a potential application in strain-sensing technologies and electrical biosensor [3]. Modification of the mechanical properties of the polymer surface has also been studied. N+ implantation in PC leads to a harder