Photoelectrochemical water oxidation over TiO₂ nanotubes modified with MoS₂ and g-C₃N₄

• Phuong Hoang Nguyen,
• Thi Minh Cao,
• Tho Truong Nguyen,
• Hien Duy Tong and
• Viet Van Pham

Beilstein J. Nanotechnol. 2022, 13, 1541–1550, doi:10.3762/bjnano.13.127

• of materials The morphology, the phase, and the vibrational characteristics of the surface functional groups of the materials were observed by field-emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), and Fourier-transform infrared spectroscopy (FTIR). Diffuse reflectance

A TiO₂@MWCNTs nanocomposite photoanode for solar-driven water splitting

• Anh Quynh Huu Le,
• Ngoc Nhu Thi Nguyen,
• Hai Duy Tran,
• Van-Huy Nguyen and
• Le-Hai Tran

Beilstein J. Nanotechnol. 2022, 13, 1520–1530, doi:10.3762/bjnano.13.125

• -scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and linear sweep voltammetry. The results show that the TiO2@MWCNTs nanocomposite has an optical bandgap of 2.5 eV, which is a significant improvement in visible-light absorption capability compared to TiO2 (3.14 eV). The

• nanocomposite characterizations The surface morphology of MWCNTs and the TiO2@MWCNTs nanocomposite is characterized by using field-emission scanning electron microscopy (FE-SEM, S4800) and transmission electron microscopy (TEM, JEOL-1400). The crystallization behavior of the catalysts is analyzed by X-ray

Hydroxyapatite–bioglass nanocomposites: Structural, mechanical, and biological aspects

• Olga Shikimaka,
• Mihaela Bivol,
• Bogdan A. Sava,
• Marius Dumitru,
• Christu Tardei,
• Beatrice G. Sbarcea,
• Daria Grabco,
• Constantin Pyrtsac,
• Daria Topal,
• Andrian Prisacaru,
• Vitalie Cobzac and
• Viorel Nacu

Beilstein J. Nanotechnol. 2022, 13, 1490–1504, doi:10.3762/bjnano.13.123

• intensity ratio between the peaks associated with the crystallographic planes (112) and (300) expressed in counts per second, and I300 represents the intensity of the characteristic peak of the crystallographic plane (300) expressed in counts per second. Scanning electron microscopy To determine the

Rapid and sensitive detection of box turtles using an electrochemical DNA biosensor based on a gold/graphene nanocomposite

• Abu Hashem,
• M. A. Motalib Hossain,
• Ab Rahman Marlinda,
• Mohammad Al Mamun,
• Khanom Simarani and
• Mohd Rafie Johan

Beilstein J. Nanotechnol. 2022, 13, 1458–1472, doi:10.3762/bjnano.13.120

• scanning electron microscopy and structural characteristics were analysed by using energy-dispersive X-ray, UV–vis, and Fourier-transform infrared spectroscopy. The electrochemical characteristics of the modified electrodes were studied by cyclic voltammetry, differential pulse voltammetry (DPV), and

• modified screen-printed carbon electrode Surface morphology and structural characterisation Field-emission scanning electron microscopy (FESEM) images of nanoparticles and their composites are depicted in Figure 2a–b, where the wrinkled regions represent specific patterns of different materials. In Figure

Orally administered docetaxel-loaded chitosan-decorated cationic PLGA nanoparticles for intestinal tumors: formulation, comprehensive in vitro characterization, and release kinetics

• Sedat Ünal,
• Osman Doğan and
• Yeşim Aktaş

Beilstein J. Nanotechnol. 2022, 13, 1393–1407, doi:10.3762/bjnano.13.115

• characterization of both coated and uncoated DCX-PLGA NPs was carried out by scanning electron microscopy (SEM). As it can be seen in Figure 1, both formulations exhibit perfectly round spheres with smooth surfaces. No free DCX crystals were found in the SEM pictures of any formulation, confirming that DCX was

Enhanced electronic transport properties of Te roll-like nanostructures

• E. R. Viana,
• N. Cifuentes and
• J. C. González

Beilstein J. Nanotechnol. 2022, 13, 1284–1291, doi:10.3762/bjnano.13.106

• under mild conditions. A large quantity of these polycrystalline nanostructures with a diameter between 100 and 900 nm and a wall thickness around 50 nm were synthesized and characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), transmission electron microscopy

• reagents used were of analytic grade, purchased from Sigma-Aldrich Chemicals Company, and directly used without further purification. Morphology, elemental analysis, and crystal structure Morphology and elemental composition of the as-prepared products were characterized by scanning electron microscopy

Studies of probe tip materials by atomic force microscopy: a review

• Ke Xu and
• Yuzhe Liu

Beilstein J. Nanotechnol. 2022, 13, 1256–1267, doi:10.3762/bjnano.13.104

• target nanotubes to Si tips under scanning electron microscopy; and attaching nanotubes to Si tips by carbon deposition. The strong adhesion of carbon deposition produces nanotube tips capable of surviving multiple surface collisions. The ability to image the fine structure of double-stranded DNA

• electric field. The nanotube tips produced by this method have strong adhesion and mechanical stability. Since the above methods require scanning electron microscopy (SEM) monitoring throughout the transfer process, the process is relatively time-consuming. Hafner et al. [40] proposed a new method to

Application of nanoarchitectonics in moist-electric generation

• Jia-Cheng Feng and
• Hong Xia

Beilstein J. Nanotechnol. 2022, 13, 1185–1200, doi:10.3762/bjnano.13.99

• in practical applications and provide green energy for more electronic devices. (a) The water flow is driven by an external electric field in the “motor” part, so the water molecules gain kinetic energy, and then an electromotive force is generated in the "Generator" part. (b) A scanning electron

• microscopy (SEM) image of an individual single-walled carbon nanotube (SWNT) device. (c) Dependence of the induced voltage difference, ΔV, on the quantity of water injected into the chamber. ΔV increases with the quantity of water inside the chamber and tends to saturate at 500 μL. It is nearly symmetric for

Rapid fabrication of MgO@g-C₃N₄ heterojunctions for photocatalytic nitric oxide removal

• Minh-Thuan Pham,
• Duyen P. H. Tran,
• Xuan-Thanh Bui and
• Sheng-Jie You

Beilstein J. Nanotechnol. 2022, 13, 1141–1154, doi:10.3762/bjnano.13.96

• properties of the materials. Scanning electron microscopy (SEM) and high-resolution transmission electron microscopy (HR-TEM) were used to assess the morphology of the materials. The crystal phase of the materials was determined by X-ray diffraction (XRD) with a measurement range of 10°–80°. Fourier

Green synthesis of zinc oxide nanoparticles toward highly efficient photocatalysis and antibacterial application

• Vo Thi Thu Nhu,
• Nguyen Duy Dat,
• Le-Minh Tam and
• Nguyen Hoang Phuong

Beilstein J. Nanotechnol. 2022, 13, 1108–1119, doi:10.3762/bjnano.13.94

• (XRD) using a Bruker D8 advanced X-ray diffractometer equipped with Cu Kα radiation (λ = 1.5418 Å). The morphology and size of the synthesized material were determined by field emission scanning electron microscopy (FESEM) on a Hitachi S-4800 at 15 kV and high-resolution transmission electron

• electron microscopy, and high-resolution transmission electron microscopy. The fabricated ZnO NP samples are crystalline with a grain size of 30–100 nm. The ZnO NPs were used as catalysts for the photodegradation of methylene blue (MB) and methyl orange (MO) under visible and UV light. The results indicate

• , Vietnam 10.3762/bjnano.13.94 Abstract Zinc oxide nanoparticles (ZnO NPs) were successfully synthesized by a green method using rosin and zinc chloride as salt precursors. The phase structure, morphology, and particle size of ZnO were determined by X-ray powder diffraction, field emission scanning

Biomimetic chitosan with biocomposite nanomaterials for bone tissue repair and regeneration

• Se-Kwon Kim,
• Sesha Subramanian Murugan,
• Pandurang Appana Dalavi,
• Sebanti Gupta,
• Sukumaran Anil,
• Gi Hun Seong and
• Jayachandran Venkatesan

Beilstein J. Nanotechnol. 2022, 13, 1051–1067, doi:10.3762/bjnano.13.92

• -hydroxybutyrate) chitosan/multiwalled carbon nanotube scaffold coated with a nanobioglass–titania scaffold on bone cell regeneration was investigated. Scanning electron microscopy (SEM) examination verified the porosity of the scaffolds in the 300–700 µm range. The incorporation of chitosan into poly(3

Spindle-like MIL101(Fe) decorated with Bi₂O₃ nanoparticles for enhanced degradation of chlortetracycline under visible-light irradiation

• Chen-chen Hao,
• Fang-yan Chen,
• Kun Bian,
• Yu-bin Tang and
• Wei-long Shi

Beilstein J. Nanotechnol. 2022, 13, 1038–1050, doi:10.3762/bjnano.13.91

• . Characterization of the as-prepared catalyst The crystalline structure of the prepared photocatalyst was analyzed by X-ray diffraction spectrometry (Empyrean, Panalytical, Holland) with Cu Kα radiation at a scanning speed of 7 °/min. The morphology of the samples was observed by scanning electron microscopy (SEM

Effects of focused electron beam irradiation parameters on direct nanostructure formation on Ag surfaces

• Jānis Sniķeris,
• Vjačeslavs Gerbreders,
• Andrejs Bulanovs and
• Ēriks Sļedevskis

Beilstein J. Nanotechnol. 2022, 13, 1004–1010, doi:10.3762/bjnano.13.87

• residual hydrocarbons by electron irradiation in scanning electron microscopy (SEM) vacuum chambers have been reported in several studies [12][13][14][15]. Hydrocarbon contamination from samples and vacuum pump oils is known to be ever present in vacuum chambers of electron microscopes [16][17][18]. The

Design of a biomimetic, small-scale artificial leaf surface for the study of environmental interactions

• Miriam Anna Huth,
• Axel Huth,
• Lukas Schreiber and
• Kerstin Koch

Beilstein J. Nanotechnol. 2022, 13, 944–957, doi:10.3762/bjnano.13.83

• plate with the wax source and the samples to be coated was 4 cm. After wax deposition, samples were stored in an oven at 50 °C for 72 h. In the following, the artificial surfaces are named according to the amount of wax used for wax coating. Scanning electron microscopy of wax morphology The

• morphologies of the wax on the upper (adaxial) and lower (abaxial) leaf sides (leaf 2, 3, and 4, n = 3) as well as of recrystallized wax structures on glass (n = 3) were analyzed by scanning electron microscopy (SEM, Gemini Supra 40 VP, Zeiss, Oberkochen, Germany). The middle part of fresh wheat leaves was cut

• electron microscopy, gas chromatography–mass spectrometry, and by the determination of water contact angles, contact angle hysteresis, and tilting angles. Wheat leaves of different ages were covered exclusively with wax platelets. The extracted wheat wax was composed of alcohols, aldehydes, esters, and

Solar-light-driven LaFe_xNi_1−xO₃ perovskite oxides for photocatalytic Fenton-like reaction to degrade organic pollutants

• Chao-Wei Huang,
• Shu-Yu Hsu,
• Jun-Han Lin,
• Yun Jhou,
• Wei-Yu Chen,
• Kun-Yi Andrew Lin,
• Yu-Tang Lin and
• Van-Huy Nguyen

Beilstein J. Nanotechnol. 2022, 13, 882–895, doi:10.3762/bjnano.13.79

• scanning electron microscopy (FESEM) images at the magnification of 100,000×, the surface of the samples with different Fe/Ni ratios were irregular and slightly different from each other. The grain surfaces of the pure LaNiO3 and LaFeO3 were chestnut-like. The observed appearance was also similar to the

• diffracting angle was set from 10° to 70° with a scan rate of 4 °/min. The crystalline sizes of the LaFexNi1−xO3 perovskite oxides were further obtained by Scherrer’s equation. To obtain the morphologies of the prepared samples, S-4800 (Hitachi, Japan) was employed to conduct field emission scanning electron

• microscopy (FESEM). The light absorption spectra of the perovskite oxides were inspected using V-670 (Jasco, Japan) to examine the UV–vis absorption capability with diffuse reflectance spectroscopy (DRS) from 200 to 800 nm. The nitrogen adsorption–desorption analyzer, ASAP 2020 PLUS (ASAP, USA), was applied

Micro-structures, nanomechanical properties and flight performance of three beetles with different folding ratios

• Jiyu Sun,
• Pengpeng Li,
• Yongwei Yan,
• Fa Song,
• Nuo Xu and
• Zhijun Zhang

Beilstein J. Nanotechnol. 2022, 13, 845–856, doi:10.3762/bjnano.13.75

• pasted flat on a slide for observation. Scanning electron microscopy (SEM) (Model EVO-18, Carl Zeiss Microimaging Inc., Germany) was used to obtain morphological images of cross sections of the hind wings of three beetles at the same locations of different wing veins. Nanoindentation properties The

• and the nanomechanical properties of the hind wings of the three beetles and the cross-sectional morphology of different wing veins were observed and tested with super depth-of-field microscopy, nanoindentation, and scanning electron microscopy. Thus, the folding ratios, reduced Young’s modulus, and

Temperature and chemical effects on the interfacial energy between a Ga–In–Sn eutectic liquid alloy and nanoscopic asperities

• Yujin Han,
• Pierre-Marie Thebault,
• Corentin Audes,
• Xuelin Wang,
• Haiwoong Park,
• Jian-Zhong Jiang and
• Arnaud Caron

Beilstein J. Nanotechnol. 2022, 13, 817–827, doi:10.3762/bjnano.13.72

• tip and liquid. Assuming a conical shape for an AFM tip, the perimeter P(δ) and the contact area A(δ) can be expressed as P(δ) = 2πδ·tan θ and where θ is the half-opening angle of the tip, which we determined by scanning electron microscopy. We determined the interfacial energy γ between tip and

Hierachical epicuticular wax coverage on leaves of Deschampsia antarctica as a possible adaptation to severe environmental conditions

• Elena V. Gorb,
• Iryna A. Kozeretska and
• Stanislav N. Gorb

Beilstein J. Nanotechnol. 2022, 13, 807–816, doi:10.3762/bjnano.13.71

• /bjnano.13.71 Abstract Using cryo scanning electron microscopy, the surface micromorphology of vegetative (leaf blade and ligule) and generative (pedicel and outer glume) organs in Deschampsia antarctica, one of the only two flowering plants native to Antarctica, was examined. Whereas the pedicel and

• . antarctica plant, which are usually exposed to the environment, using cryo scanning electron microscopy (cryo-SEM) allowing for a high-resolution imaging of frozen and fractured samples in native condition, that is, without treatment in strong solvents, such as ethanol or acetone, usually needed in the

• sample preparation for conventional scanning electron microscopy. This method provided qualitatively new information about the superficial layers on vegetative organs studied in this plant species. Based on the obtained results and literature data, we discuss a possible role of the complex, hierarchical

Hierarchical Bi₂WO₆/TiO₂-nanotube composites derived from natural cellulose for visible-light photocatalytic treatment of pollutants

• Zehao Lin,
• Zhan Yang and
• Jianguo Huang

Beilstein J. Nanotechnol. 2022, 13, 745–762, doi:10.3762/bjnano.13.66

• homogeneous suspension. The suspension was then dropped onto an Al foil to be observed via field-emission scanning electron microscopy (FE-SEM), and onto a carbon-supported copper grid for examination via transmission electron microscopy (TEM) and high resolution transmission electron microscopy (HR-TEM

A nonenzymatic reduced graphene oxide-based nanosensor for parathion

• Sarani Sen,
• Anurag Roy,
• Ambarish Sanyal and
• Parukuttyamma Sujatha Devi

Beilstein J. Nanotechnol. 2022, 13, 730–744, doi:10.3762/bjnano.13.65

• phase of GO and RGO was characterized by X-ray diffraction (XRD) using a X’pertpro MPD XRD (PAN analytical B.V., the Netherlands) with Cu Kα radiation (λ = 1.5406 Å). Scanning electron microscopy (SEM) of the modified electrode was conducted on a JEOLEVO® 18 special edition (model: ZEISS EVO-MA 10) at

• an acceleration voltage of 15 kV. The morphological characteristics of the electrodeposited ERGO were obtained by field-emission scanning electron microscopy (FESEM, model: LEO 430i, Carl Zeiss) and high-resolution transmission electron microscopy (model: Tecnai G2 30ST, FEI) operating at 300 kV

Nanoarchitectonics of the cathode to improve the reversibility of Li–O₂ batteries

• Hien Thi Thu Pham,
• Jonghyeok Yun,
• So Yeun Kim,
• Sang A Han,
• Jung Ho Kim,
• Jong-Won Lee and
• Min-Sik Park

Beilstein J. Nanotechnol. 2022, 13, 689–698, doi:10.3762/bjnano.13.61

• , and Zn1Co4 particles grown on CNT frameworks, respectively. Field-emission scanning electron microscopy (FESEM) observations confirmed that abundant rhombic dodecahedral ZnxCoy particles with different Zn/Co ratios were successfully integrated into the CNTs. Corresponding energy-dispersive X-ray

• atmosphere, the ZnxCoy–C/CNT composite was obtained and further chemically etched with 1 M of H2SO4 solution before use. Material characterization Field-emission scanning electron microscopy (JEOL, JSM-7000F) and high-resolution TEM (HRTEM, JEOL, JEM-2100F) with EDS were used to examine the morphologies and

Experimental and theoretical study of field-dependent spin splitting at ferromagnetic insulator–superconductor interfaces

• Peter Machon,
• Michael J. Wolf,
• Detlef Beckmann and
• Wolfgang Belzig

Beilstein J. Nanotechnol. 2022, 13, 682–688, doi:10.3762/bjnano.13.60

• of the ferromagnetic insulator europium sulfide. Figure 4 shows a false-color scanning electron microscopy image of the sample, together with the experimental scheme. The sample was fabricated in a two-step procedure: First, a EuS film of 44 nm thickness was created by e-beam evaporation of EuS onto

• values of ε’ = [100,0.1]. Density of states in a superconductor in proximity to a ferromagnetic insulator indicated by the spin mixing angle δφ, with (from (a) to (d)) ε’ = 100,10,1,0.1, while the superconducting order parameter is evaluated self-consistently (T ≪ Tc). False-color scanning electron

• microscopy image of the sample and experimental scheme. (a) Differential conductance g as a function of the bias V for different applied magnetic fields B (symbols), and fits with our model (lines). (b) Spin mixing angle δφ (left axis) and pair potential Δ (right axis) as functions of the applied field B

Reliable fabrication of transparent conducting films by cascade centrifugation and Langmuir–Blodgett deposition of electrochemically exfoliated graphene

• Teodora Vićentić,
• Stevan Andrić,
• Vladimir Rajić and
• Marko Spasenović

Beilstein J. Nanotechnol. 2022, 13, 666–674, doi:10.3762/bjnano.13.58

• 10× (Olympus BX53M). Scanning electron microscopy (SEM) was performed with a FESEM (FEI Scios 2, Thermo Fisher Scientific, Waltham, MA, USA) at a chamber pressure of 1 × 10−4 Pa with electron beam voltages set between 1 and 30 kV, depending on the film. Films that are shown in optical dark-field

Antibacterial activity of a berberine nanoformulation

• Hue Thi Nguyen,
• Tuyet Nhung Pham,
• Anh-Tuan Le,
• Nguyen Thanh Thuy,
• Tran Quang Huy and
• Thuy Thi Thu Nguyen

Beilstein J. Nanotechnol. 2022, 13, 641–652, doi:10.3762/bjnano.13.56

• solution were determined using Fourier-transform infrared spectroscopy (FTIR, NEXUS 670 from Nicolet). The FTIR analysis was conducted in transmission mode in the wavenumber range of 400 to 4000 cm−1. Size and shape of BBR NPs were investigated by scanning electron microscopy (SEM, S-4800, Hitachi) and

Sodium doping in brookite TiO₂ enhances its photocatalytic activity

• Boxiang Zhuang,
• Honglong Shi,
• Honglei Zhang and
• Zeqian Zhang

Beilstein J. Nanotechnol. 2022, 13, 599–609, doi:10.3762/bjnano.13.52

• , which is different from that observed via scanning electron microscopy (SEM) or transmission electron microscopy (TEM). Samples calcinated at 300–600 °C have a similar crystal size (ranging from 39–43 nm), suggesting that there is no obvious correlation between the crystal size and the photocatalytic