Sustainable fabrication of 2D-based devices through reuse of substrates with microfabricated electrodes

• Ying Zhang,
• Yigit Sozen,
• Esteban Zamora-Amo,
• Thomas Pucher,
• Nuria Jiménez-Arévalo,
• Zdenek Sofer,
• Yong Xie and
• Andres Castellanos-Gomez

Beilstein J. Nanotechnol. 2026, 17, 818–827, doi:10.3762/bjnano.17.58

• research is essential but often limited by the high cost and need for specialized facilities. This study establishes a practical method for cleaning and reusing substrates with pre-patterned electrodes. The cleaning protocol involves the use of an ultrasonic bath in warm N-methyl-2-pyrrolidone (NMP

• . Keywords: 2D device fabrication; microfabricated electrode; N-methyl-2-pyrrolidone; substrate reuse; ultrasonic cleaning; Introduction Nanoscience research often needs the fabrication of proof-of-concept devices to demonstrate applications of novel nanomaterials or to study their fundamental properties [1

• have mainly focused on epitaxial growth or electrochemical sensing applications. In contrast, this work addresses the reuse of substrates for 2D material-based electronic devices. The cleaning process consists of an ultrasonic bath in N-methyl-2-pyrrolidone (NMP) [23][24] at 50 °C, followed by acetone

Dendrimer-modified carbon nanotubes for the removal and recovery of heavy metal ions from water

• Thao Quynh Ngan Tran,
• Huu Trung Nguyen,
• Subodh Kumar and
• Xuan Thang Cao

Beilstein J. Nanotechnol. 2025, 16, 1522–1532, doi:10.3762/bjnano.16.107

• moieties and polymers; however, it typically involves harmful organic solvents (e.g., N-methyl-2-pyrrolidone and dimethylformamide) and reagents [36][37][38]. Fortunately, deep eutectic solvents (DESs) have been identified as suitable catalytic media for Diels–Alder reactions without the need for external

In situ magnesiothermic reduction synthesis of a Ge@C composite for high-performance lithium-ion batterie anodes

• Ha Tran Huu,
• Ngoc Phi Nguyen,
• Vuong Hoang Ngo,
• Huy Hoang Luc,
• Minh Kha Le,
• Minh Thu Nguyen,
• My Loan Phung Le,
• Hye Rim Kim,
• In Young Kim,
• Sung Jin Kim,
• Van Man Tran and
• Vien Vo

Beilstein J. Nanotechnol. 2023, 14, 751–761, doi:10.3762/bjnano.14.62

• microscopy (HR-TEM, JEOL JEM-2100F) were conducted for morphology and particle size investigation. A well-blended mixture of active material, conductive carbon C65, and polyvinylidene fluoride (PVDF) binder with a mass ratio of 75:15:10 in N-methyl-2-pyrrolidone solvent was used for fabricating the working

Solution combustion synthesis of a nanometer-scale Co₃O₄ anode material for Li-ion batteries

• Monika Michalska,
• Huajun Xu,
• Qingmin Shan,
• Shiqiang Zhang,
• Yohan Dall'Agnese,
• Yu Gao,
• Amrita Jain and
• Marcin Krajewski

Beilstein J. Nanotechnol. 2021, 12, 424–431, doi:10.3762/bjnano.12.34

• working electrode, a slurry composed of previously prepared Co3O4 material, super P carbon (Saibo), and polyvinylidene difluoride (PVDF; Arkema) (weight ratio of 8:1:1) mixed in N-methyl-2-pyrrolidone was prepared and then coated on copper foil by using a doctor blade. After that, the electrode was dried

Exfoliation in a low boiling point solvent and electrochemical applications of MoO₃

• Matangi Sricharan,
• Bikesh Gupta,
• Sreejesh Moolayadukkam and
• H. S. S. Ramakrishna Matte

Beilstein J. Nanotechnol. 2020, 11, 662–670, doi:10.3762/bjnano.11.52

• some applications. To alleviate this, LPE has been carried out in organic solvents taking into account the Hansen solubility parameters (HSPs) [9]. To exfoliate MoO3 in organic solvents without any additives, Coleman et al. have found that N-methyl-2-pyrrolidone (NMP), N-cyclohexyl-2-pyrrolidone, and

Design and facile synthesis of defect-rich C-MoS₂/rGO nanosheets for enhanced lithium–sulfur battery performance

• Chengxiang Tian,
• Juwei Wu,
• Zheng Ma,
• Bo Li,
• Pengcheng Li,
• Xiaotao Zu and
• Xia Xiang

Beilstein J. Nanotechnol. 2019, 10, 2251–2260, doi:10.3762/bjnano.10.217

• , C-MoS2/rGO-S, C-MoS2/rGO-4-S, C-MoS2/rGO-6-S, C-MoS2/rGO-8-S), 10 wt % acetylene black and 10 wt % polyvinylidene fiuoride (PVDF) in N-methyl-2-pyrrolidone (NMP) on an Al foil current collector. Then, the electrodes were dried in vacuum at 60 °C for 12 h. The electrode was manufactured in a coin

TiO₂/GO-coated functional separator to suppress polysulfide migration in lithium–sulfur batteries

• Ning Liu,
• Lu Wang,
• Taizhe Tan,
• Yan Zhao and
• Yongguang Zhang

Beilstein J. Nanotechnol. 2019, 10, 1726–1736, doi:10.3762/bjnano.10.168

• diameter of 18 mm. For reference, a pure GO-modified separator was fabricated using the same process. Synthesis of sulfur cathode The sulfur cathode was prepared by mixing 70 wt % of elemental sulfur, 10 wt % PVDF and 20 wt % Ketjen black in N-methyl-2-pyrrolidone (NMP) solvent to form a slurry, which was

Flexible freestanding MoS₂-based composite paper for energy conversion and storage

• Florian Zoller,
• Jan Luxa,
• Thomas Bein,
• Dina Fattakhova-Rohlfing,
• Daniel Bouša and
• Zdeněk Sofer

Beilstein J. Nanotechnol. 2019, 10, 1488–1496, doi:10.3762/bjnano.10.147

• the synthesis of a freestanding MoS2-based composite paper using a small addition of single-walled carbon nanotubes (SWCNTs) and shear-force milling in N-methyl-2-pyrrolidone (NMP). The paper was prepared simply by vacuum filtration of the slurry on top of a filter. The resulting material exhibits

• rate performance tests. These findings show that the reported material is also promising for application in flexible batteries. Experimental Materials MoS2 was purchased from Alfa Aesar, TUBALLTM SWCNTs were purchased from OCSiAl, and N-methyl-2-pyrrolidone (NMP) was purchased from Sigma-Aldrich. The

An efficient electrode material for high performance solid-state hybrid supercapacitors based on a Cu/CuO/porous carbon nanofiber/TiO₂ hybrid composite

• Mamta Sham Lal,
• Thirugnanam Lavanya and
• Sundara Ramaprabhu

Beilstein J. Nanotechnol. 2019, 10, 781–793, doi:10.3762/bjnano.10.78

• material slurry was prepared using a mixture of the material, i.e., polyvinylidene fluoride (PVDF) as binder (15%), conductive carbon (10%) and active material (75%) in N-methyl-2-pyrrolidone (NMP) solvent to form a viscous slurry using a mortar and pestle. This slurry was coated on the carbon sheet with

Temperature-dependent Raman spectroscopy and sensor applications of PtSe₂ nanosheets synthesized by wet chemistry

• Mahendra S. Pawar and
• Dattatray J. Late

Beilstein J. Nanotechnol. 2019, 10, 467–474, doi:10.3762/bjnano.10.46

• device fabrication and testing Sensor devices were fabricated on a tin-doped indium oxide (ITO) substrate with a channel length of ≈300 µm and width ≈5 mm. The PtSe2 nanosheet powder was dispersed in N-methyl-2-pyrrolidone (NMP) solvent and then drop casted between the channels. The devices were further

Effects of post-lithography cleaning on the yield and performance of CVD graphene-based devices

• Eduardo Nery Duarte de Araujo,
• Thiago Alonso Stephan Lacerda de Sousa,
• Luciano de Moura Guimarães and
• Flavio Plentz

Beilstein J. Nanotechnol. 2019, 10, 349–355, doi:10.3762/bjnano.10.34

• (Figure 1e) and the lift-off as well (Figure 1j) were performed whith the resist stripper, N-methyl-2-pyrrolidone (NMP), followed by rinsing in isopropanol (IPA) and deionized water (DI, Figure 2a,b). Figure 2c shows that this procedure seriously damages graphene. We attribute this to the well-known high

Pull-off and friction forces of micropatterned elastomers on soft substrates: the effects of pattern length scale and stiffness

• Peter van Assenbergh,
• Marike Fokker,
• Julian Langowski,
• Jan van Esch,
• Marleen Kamperman and
• Dimitra Dodou

Beilstein J. Nanotechnol. 2019, 10, 79–94, doi:10.3762/bjnano.10.8

• -polymer (base) and crosslinker (curing agent) were purchased from Dow Corning, poly(vinyl alcohol) (PVA, Selvol PVOH 165; hydrolysis rate: 99.65% ± 0.35%; degree of polymerization: about 2000, as reported by the manufacturer) was purchased from Sekisui Chemical Group. N-methyl-2-pyrrolidone (NMP) was

Nitrogen-doped carbon nanotubes coated with zinc oxide nanoparticles as sulfur encapsulator for high-performance lithium/sulfur batteries

• Yan Zhao,
• Zhengjun Liu,
• Liancheng Sun,
• Yongguang Zhang,
• Yuting Feng,
• Xin Wang,
• Indira Kurmanbayeva and
• Zhumabay Bakenov

Beilstein J. Nanotechnol. 2018, 9, 1677–1685, doi:10.3762/bjnano.9.159

• wt % polyvinylidene fluoride (PVDF) in N-methyl-2-pyrrolidone (NMP). The resulting homogeneous slurry was coated on nickel foam and subsequently dried at 75 °C overnight. Metallic lithium foil served as a counter and reference electrode, and micro-porous polypropylene film (Cellgard 2300) was used as

Synthesis and characterization of electrospun molybdenum dioxide–carbon nanofibers as sulfur matrix additives for rechargeable lithium–sulfur battery applications

• Ruiyuan Zhuang,
• Shanshan Yao,
• Maoxiang Jing,
• Xiangqian Shen,
• Jun Xiang,
• Tianbao Li,
• Kesong Xiao and
• Shibiao Qin

Beilstein J. Nanotechnol. 2018, 9, 262–270, doi:10.3762/bjnano.9.28

• with acetylene black and polyvinylidene fluoride (PVDF) in N-methyl-2-pyrrolidone (NMP) at a weight ratio of 7:2:1. The slurry was spread onto aluminum foil (thickness: 20 μm) and dried in vacuum at 60 °C for 12 h. Electrodes were made from punching circular discs with a diameter of 12 mm and sulfur

A biofunctionalizable ink platform composed of catechol-modified chitosan and reduced graphene oxide/platinum nanocomposite

• Peter Sobolewski,
• Agata Goszczyńska,
• Małgorzata Aleksandrzak,
• Karolina Urbaś,
• Joanna Derkowska,
• Agnieszka Bartoszewska,
• Jacek Podolski,
• Ewa Mijowska and
• Mirosława El Fray

Beilstein J. Nanotechnol. 2017, 8, 1508–1514, doi:10.3762/bjnano.8.151

• . While graphene oxide can be readily dispersed in aqueous solutions, graphene and rGO require appropriate organic solvents [11]. N-methyl-2-pyrrolidone (NMP) is perhaps the ideal solvent for the exfoliation of graphite and graphene. However, the aggressive nature of this solvent led us to choose ethylene

Deposition of exchange-coupled dinickel complexes on gold substrates utilizing ambidentate mercapto-carboxylato ligands

• Martin Börner,
• Laura Blömer,
• Marcus Kischel,
• Peter Richter,
• Georgeta Salvan,
• Dietrich R. T. Zahn,
• Pablo F. Siles,
• Maria E. N. Fuentes,
• Carlos C. B. Bufon,
• Daniel Grimm,
• Oliver G. Schmidt,
• Daniel Breite,
• Bernd Abel and
• Berthold Kersting

Beilstein J. Nanotechnol. 2017, 8, 1375–1387, doi:10.3762/bjnano.8.139

• purification in the next step. Synthesis of H2L6, step 4,4'-mercapto-[1,1'-biphenyl]-4-carboxylic acid 4'-(Methylthio)-[1,1'-biphenyl]-4-carboxylic acid (428 mg, 1.75 mmol) and NaSCH3 were dissolved in degassed N-methyl-2-pyrrolidone (40 mL) and stirred at 110 °C for 72 h. The solvent was removed in vacuo, the

Carbon nanotube-wrapped Fe₂O₃ anode with improved performance for lithium-ion batteries

• Guoliang Gao,
• Yan Jin,
• Qun Zeng,
• Deyu Wang and
• Cai Shen

Beilstein J. Nanotechnol. 2017, 8, 649–656, doi:10.3762/bjnano.8.69

• %), conductive carbon black (Super P, 20 wt %) and polyvinylidene fluoride (PVDF, 10 wt %) were mixed in N-methyl-2-pyrrolidone to form a uniform slurry that was and stirred for 6 h. The slurry was spread on to the surface of a copper foil using a medical blade. The casted film was heated at 110 °C for 12 h in a

α-((4-Cyanobenzoyl)oxy)-ω-methyl poly(ethylene glycol): a new stabilizer for silver nanoparticles

• Jana Lutze,
• Miguel A. Bañares,
• Marcos Pita,
• Andrea Haase,
• Andreas Luch and
• Andreas Taubert

Beilstein J. Nanotechnol. 2017, 8, 627–635, doi:10.3762/bjnano.8.67

• removed from the heating bath for DLS and zeta-potential measurements. Analytical methods Gel permeation chromatography. GPC measurements were done on two 300 × 8 mm2 PSS-GRAM (7 µm particles) columns with porosities of 102–103 Å in N-methyl-2-pyrrolidone (NMP + 0.5 wt % LiBr at 70 °C and a flow rate of

Effect of nanostructured carbon coatings on the electrochemical performance of Li_1.4Ni_0.5Mn_0.5O_2+x-based cathode materials

• Konstantin A. Kurilenko,
• Oleg A. Shlyakhtin,
• Oleg A. Brylev,
• Dmitry I. Petukhov and
• Alexey V. Garshev

Beilstein J. Nanotechnol. 2016, 7, 1960–1970, doi:10.3762/bjnano.7.187

• a constant analyzer pass energy mode of 5 eV resulting in a resolution better than 0.3 eV. For the preparation of the electrodes, the cathode paste (active material (85 wt %), acetylene black (10 wt %, Timcal) and polyvinylidene fluoride (5 wt %, solved in N-methyl-2-pyrrolidone) was coated on a

Carbon nano-onions (multi-layer fullerenes): chemistry and applications

• Juergen Bartelmess and
• Silvia Giordani

Beilstein J. Nanotechnol. 2014, 5, 1980–1998, doi:10.3762/bjnano.5.207

• form reactive bis-radicals [31]. After ultrasonication and heating of the CNOs and BODA in N-methyl-2-pyrrolidone (NMP) in a pressure vessel, a CNO–BODA copolymer was obtained. NMP suspensions of the CNO–BODA copolymer were found to be very stable, even at high concentrations of up to 0.67 mg·mL−1

Electrochemical and electron microscopic characterization of Super-P based cathodes for Li–O₂ batteries

• Mario Marinaro,
• Santhana K. Eswara Moorthy,
• Jörg Bernhard,
• Ludwig Jörissen,
• Margret Wohlfahrt-Mehrens and
• Ute Kaiser

Beilstein J. Nanotechnol. 2013, 4, 665–670, doi:10.3762/bjnano.4.74

• cells were prepared by airbrushing a suspension of Super-P (Timcal) and polyvinylidene fluoride (PvdF) in N-methyl-2-pyrrolidone (mass ratio Super-P/PvdF 8:2) on a gas diffusion layer (Toray paper). The obtained electrodes of 12 mm in diameter were first dried at 100 °C in order to allow the evaporation

A facile approach to nanoarchitectured three-dimensional graphene-based Li–Mn–O composite as high-power cathodes for Li-ion batteries

• Wenyu Zhang,
• Yi Zeng,
• Chen Xu,
• Ni Xiao,
• Yiben Gao,
• Lain-Jong Li,
• Xiaodong Chen,
• Huey Hoon Hng and
• Qingyu Yan

Beilstein J. Nanotechnol. 2012, 3, 513–523, doi:10.3762/bjnano.3.59

• half cells. The electrodes were fabricated by mixing LMO/G (90 wt %) and poly(vinylidene fluoride) (10 wt %) in N-methyl-2-pyrrolidone. The mixture was stirred overnight and then cast onto aluminium foils to form uniform electrodes followed by drying in vacuum at 50 °C for 10 h. As for pure LMO