Growth of lithium hydride thin films from solutions: Towards solution atomic layer deposition of lithiated films

• Ivan Kundrata,
• Karol Fröhlich,
• Lubomír Vančo,
• Matej Mičušík and
• Julien Bachmann

Beilstein J. Nanotechnol. 2019, 10, 1443–1451, doi:10.3762/bjnano.10.142

• , especially when combined with substrates of high surface area, which allow for increased capacity values. One such example is the V2O5–SnO2 nanobattery [6] grown on anodized alumina. ALD can also deposit lithiated films, using precursors such as Li(thd), lithium tert-butoxide, and lithium

Gas sensing properties of individual SnO₂ nanowires and SnO₂ sol–gel nanocomposites

• Alexey V. Shaposhnik,
• Dmitry A. Shaposhnik,
• Sergey Yu. Turishchev,
• Olga A. Chuvenkova,
• Stanislav V. Ryabtsev,
• Alexey A. Vasiliev,
• Xavier Vilanova,
• Francisco Hernandez-Ramirez and
• Joan R. Morante

Beilstein J. Nanotechnol. 2019, 10, 1380–1390, doi:10.3762/bjnano.10.136

• nanowire synthesis was developed and reported in detail in the classic work of R. Wagner and W. Ellis [1]. Recently, with the use of this method, SnO2, In2O3, WO3, ZnO and other metal oxide nanowires were obtained [1][2][3][4][5]. Liquid phase synthesis methods have also been widely implemented [6][7][8][9

• show high sensitivity [10][11][12][13][14][15][16][17][18][19][20]. Hierarchical structures with SnO2 nanowires covered with additional nanoscale objects can be used for the improvement of electrical contacts [11][16][17]. A second direction in nanowire sensor development is the manufacturing of

• Virgili (Tarragona, Spain). The preliminary results concerning this publication were discussed at Eurosensors conferences [32][33]. The present work presents a comparative study of the material properties of SnO2 devices prepared by different methods and by using ammonia as a reference gas for the

Concurrent nanoscale surface etching and SnO₂ loading of carbon fibers for vanadium ion redox enhancement

• Jun Maruyama,
• Shohei Maruyama,
• Tomoko Fukuhara,
• Toru Nagaoka and
• Kei Hanafusa

Beilstein J. Nanotechnol. 2019, 10, 985–992, doi:10.3762/bjnano.10.99

• single heat-treatment step. The subsequent thermal oxidation concurrently achieved nanoscale surface etching and loading with SnO2 nanoparticles. The nanoscale-etched and SnO2-loaded surface was characterized by field-emission scanning electron microscopy (FESEM), Raman spectroscopy, and X-ray

• -oxide nanoparticles to further enhance the activity and found that through the thermal oxidation of the carbonaceous thin film derived from SnPc both types of enhancement can be concurrently achieved. The formed metal oxide, SnO2, is one of the candidates for a durable catalyst support used in an acidic

• electrolyte [19]; thus, is assumed to also be stable in the RFB environment. The activity for both the positive and negative electrode reactions of a VRFB were clearly enhanced at the finely etched and SnO2-loaded carbon-fiber electrode and a stable performance was demonstrated by full cell cycle tests

Trapping polysulfide on two-dimensional molybdenum disulfide for Li–S batteries through phase selection with optimized binding

• Sha Dong,
• Xiaoli Sun and
• Zhiguo Wang

Beilstein J. Nanotechnol. 2019, 10, 774–780, doi:10.3762/bjnano.10.77

• composed of 1T'-phases and 2H-phases [33]. The composites of 1T'-MoS2 with other active materials, such as graphene [34], carbon nanotubes [35], Mxene [36], and SnO2 [37], have received much attention regarding the use as cathodes for Li–S batteries. The electrochemical performance including the capacity

Sub-wavelength waveguide properties of 1D and surface-functionalized SnO₂ nanostructures of various morphologies

• Venkataramana Bonu,
• Binaya Kumar Sahu,
• Arindam Das,
• Sankarakumar Amirthapandian,
• Sandip Dhara and
• Harish C. Barshilia

Beilstein J. Nanotechnol. 2019, 10, 379–388, doi:10.3762/bjnano.10.37

• Laboratories, Bangalore 560017, India Materials Physics Division, Indira Gandhi Center for Atomic Research, Homi Bhabha National Institute, Kalpakkam 603102, India 10.3762/bjnano.10.37 Abstract One-dimensional (1D) SnO2 sub-wavelength waveguides are a critical contribution to advanced optoelectronics. Further

• understanding of the surface defects and role of morphology in 1D SnO2 nanowires can help to better utilize these nanostructures more efficiently. For this purpose, three different nanowires (NWs), namely belts, cylindrical- and square-shaped structures were grown using SnO2 quantum dots as a precursor material

• behavior was also demonstrated in tapered and surface-functionalized SnO2 NWs. While the tapered waveguide can allow for easy focusing of light, the simple surface chemistry offers selective light propagation by tuning the luminescence. Defect-related PL in NWs is studied using temperature-dependent

Uniform Sb₂S₃ optical coatings by chemical spray method

• Jako S. Eensalu,
• Atanas Katerski,
• Erki Kärber,
• Ilona Oja Acik,
• Arvo Mere and
• Malle Krunks

Beilstein J. Nanotechnol. 2019, 10, 198–210, doi:10.3762/bjnano.10.18

• ]. The crystallites oriented along the (2 0 1) plane were 24 nm in size in Sb2S3 layers grown on SnO2/F (FTO) coated glass substrates via thermal evaporation [27]. The crystallite size was 52 nm along the (3 0 1) plane in Sb2S3 layers grown on glass substrates at 250 °C via spray pyrolysis [28], similar

Nanoporous water oxidation electrodes with a low loading of laser-deposited Ru/C exhibit enhanced corrosion stability

• Sandra Haschke,
• Dmitrii Pankin,
• Vladimir Mikhailovskii,
• Maïssa K. S. Barr,
• Adriana Both-Engel,
• Alina Manshina and
• Julien Bachmann

Beilstein J. Nanotechnol. 2019, 10, 157–167, doi:10.3762/bjnano.10.15

• and Co [22]). Another approach entails increasing the specific surface area, which allows one to generate current at lower overpotential, for example by supporting RuO2 nanoparticles on siliceous mesoporous materials [23][24][25][26], with mesoporous RuO2 [27], or with RuO2 supported on Sb-doped SnO2

Zn/F-doped tin oxide nanoparticles synthesized by laser pyrolysis: structural and optical properties

• Florian Dumitrache,
• Iuliana P. Morjan,
• Elena Dutu,
• Ion Morjan,
• Claudiu Teodor Fleaca,
• Monica Scarisoreanu,
• Alina Ilie,
• Marius Dumitru,
• Cristian Mihailescu,
• Adriana Smarandache and
• Gabriel Prodan

Beilstein J. Nanotechnol. 2019, 10, 9–21, doi:10.3762/bjnano.10.2

• -Magurele, Romania Ovidius University of Constanta, Mamaia Avenue no. 124, 900524, Constanta, Romania 10.3762/bjnano.10.2 Abstract Zn/F co-doped SnO2 nanoparticles with a mean diameter of less than 15 nm and a narrow size distribution were synthesized by a one-step laser pyrolysis technique using a

• reactive mixture containing tetramethyltin (SnMe4) and diethylzinc (ZnEt2) vapors, diluted Ar, O2 and SF6. Their structural, morphological, optical and electrical properties are reported in this work. The X-ray diffraction (XRD) analysis shows that the nanoparticles possess a tetragonal SnO2 crystalline

• dopant concentration). Keywords: laser pyrolysis; nanoparticles; optical bandgap; Zn/F-doped SnO2; Introduction Recently, there has been growing interest in the field of transparent conducting oxides and wide bandgap oxide nanocrystalline materials such as tin oxide (SnO2). It is generally agreed that

Graphene-enhanced metal oxide gas sensors at room temperature: a review

• Dongjin Sun,
• Yifan Luo,
• Marc Debliquy and
• Chao Zhang

Beilstein J. Nanotechnol. 2018, 9, 2832–2844, doi:10.3762/bjnano.9.264

• achieved at all [19][20]. Metal-oxide semiconductors (MOS), including tin oxide (SnO2), titanium dioxide (TiO2), zinc oxide (ZnO), copper oxide (CuO), tungsten oxide (WO3), indium oxide (In2O3), ferric oxide (Fe2O3) and cobalt oxide (Co3O4) are important materials for gas sensors [21][22][23][24][25][26

• the single components. The mechanisms through which graphene enhances the sensing performance of MOS sensors will be interpreted in the following sections. Wang et al. [35] reported that a formaldehyde (HCHO) sensor based on SnO2–GO composites, fabricated via electrospinning, exhibited a three times

• higher sensitivity than that of the pure SnO2 sensor at 120 °C. The composite sensor was able to detect 500 ppb HCHO. The unique sensing properties of SnO2–GO sensor was interpreted by the large specific surface area, the high number of oxygen functional groups and electric regulation effects provided

Electrospun one-dimensional nanostructures: a new horizon for gas sensing materials

• Muhammad Imran,
• Nunzio Motta and
• Mahnaz Shafiei

Beilstein J. Nanotechnol. 2018, 9, 2128–2170, doi:10.3762/bjnano.9.202

• flow or disperse to form a uniform homogeneous solution. The former gives rise to bi-component nanofibers, while the latter produces blended polymer fibers. Dual-layer TiO2/SnO2 nanofibers have been reported by Liu et al. [72] using two syringes containing different solutions linked to a common

• fabrication strategy for synthesis of SnO2 NFs with a branch-on-stem morphology using electrospinning, oxygen plasma etching, sputtering and annealing. Electrospun PVP NFs were first etched with oxygen plasma to make a hierarchical template. Afterwards, a SnO2 film is deposited by sputtering and the PVP

• template is removed by annealing. The morphology of the NFs is dependent on sputtering time, resulting in uniformly distributed branches all over stem. Jun et al. [77] developed polypyrrole (PPy)-coated SnO2 tube-in-tube structures using single-nozzle electrospinning with a phase separation solvent method

Cr(VI) remediation from aqueous environment through modified-TiO₂-mediated photocatalytic reduction

• Rashmi Acharya,
• Brundabana Naik and
• Kulamani Parida

Beilstein J. Nanotechnol. 2018, 9, 1448–1470, doi:10.3762/bjnano.9.137

• conditions, low cost, high efficiency and reusability. It uses renewable and pollution-free solar energy and produces minimal secondary waste without using toxic chemicals that follow the rules of green chemistry [59][60][61]. Various semiconductor photocatalysts such as CdS, ZnO, WO3, SnO2, and TiO2 have

Semi-automatic spray pyrolysis deposition of thin, transparent, titania films as blocking layers for dye-sensitized and perovskite solar cells

• Hana Krýsová,
• Josef Krýsa and
• Ladislav Kavan

Beilstein J. Nanotechnol. 2018, 9, 1135–1145, doi:10.3762/bjnano.9.105

• function of the negative electrode of dye-sensitized and perovskite solar cells, the deposition of a nonporous blocking film is required on the surface of F-doped SnO2 (FTO) glass substrates. Such a blocking film can minimise undesirable parasitic processes, for example, the back reaction of photoinjected

• accompanied by the undesirable back reaction of photoinjected electrons with the hole-transporting medium or the oxidized mediator. This reaction occurs both at the TiO2 surface and at the exposed areas of the F-doped SnO2 (FTO) conducting glass that are not covered by the titanium dioxide nanoparticles. In

• liquid-type DSSCs there is a relatively small recombination current as compared to FTO, which becomes critical in SSDSSCs and perovskite solar cells [3]. For proper function of these solar cells, a semiconducting nonporous blocking layer of oxide (usually TiO2 or SnO2) must be deposited on top of FTO to

Gas-sensing behaviour of ZnO/diamond nanostructures

• Marina Davydova,
• Alexandr Laposa,
• Jiri Smarhak,
• Alexander Kromka,
• Neda Neykova,
• Josef Nahlik,
• Jiri Kroutil,
• Jan Drahokoupil and
• Jan Voves

Beilstein J. Nanotechnol. 2018, 9, 22–29, doi:10.3762/bjnano.9.4

• ]. Sadek et al. fabricated a ZnO nanobelt sensor and tested it for NO2 gas at operating temperatures between 150 and 450 °C. The optimum operating temperature for NO2 detection was in the range between 300 °C and 350 °C [25]. The sensing properties of various ZnO nanostructures (ZnO nanowires and ZnO–SnO2

• core–shell nanowires) were investigated by Hwang and co-workers. The gas response of ZnO–SnO2 core–shell nanowires to 10 ppm NO2 at 200 °C and 300 °C were 66.3 and 12.4, respectively, which is ca. 33- and ca. 8.9-times higher than the respective values of 2.0 and 1.4 for ZnO nanowires [26]. Presently

Enhanced photoelectrochemical water splitting performance using morphology-controlled BiVO₄ with W doping

• Xin Zhao and
• Zhong Chen

Beilstein J. Nanotechnol. 2017, 8, 2640–2647, doi:10.3762/bjnano.8.264

• diffraction was used to characterize the crystal structure of the obtained films. Figure 2 shows that all peaks agree well with the ones of BiVO4 (PDF#14-0688). No peaks belonging to other phases were present except the ones from the fluorine-doped tin oxide (SnO2) substrate. This demonstrates BiVO4 thin

Freestanding graphene/MnO₂ cathodes for Li-ion batteries

• Şeyma Özcan,
• Aslıhan Güler,
• Tugrul Cetinkaya,
• Mehmet O. Guler and
• Hatem Akbulut

Beilstein J. Nanotechnol. 2017, 8, 1932–1938, doi:10.3762/bjnano.8.193

• density of Li-ion batteries is desired in order to store more, efficient energy. Although researchers have made significant progress in the development of high capacity anode electrodes, such as SnO2 [2], Sn-Ni [3], and Si [4], the performance of cathodes has been bottlenecked by the energy density and

Two-dimensional carbon-based nanocomposites for photocatalytic energy generation and environmental remediation applications

• Suneel Kumar,
• Ashish Kumar,
• Ashish Bahuguna,
• Vipul Sharma and
• Venkata Krishnan

Beilstein J. Nanotechnol. 2017, 8, 1571–1600, doi:10.3762/bjnano.8.159

• ]. Hence, in the recent decade, heterogeneous photocatalysis has been widely explored for the conversion of solar energy into chemical energy and for pollutant removal from water [11][12]. Up to now, various interesting semiconductors such as TiO2, ZnO, WO3, CdS, Bi2O3, Fe2O3, SnO2, BiVO4, etc. have been

• coupling with semiconductor materials such as TiO2 [73], ZnO [74], CdS [75], SnO2 [76], CeO2 [77], WO3 [78], Fe2O3 [79], Ag3PO4 [80], Ag3VO4 [81], ZnWO4 [82], SrTiO3 [83], BiVO4 [84], Bi2WO6 [85], BiOX [86][87], etc. These heterojunction formations have proved to be an effective method to improve the

Fabrication of hierarchically porous TiO₂ nanofibers by microemulsion electrospinning and their application as anode material for lithium-ion batteries

• Jin Zhang,
• Yibing Cai,
• Xuebin Hou,
• Xiaofei Song,
• Pengfei Lv,
• Huimin Zhou and
• Qufu Wei

Beilstein J. Nanotechnol. 2017, 8, 1297–1306, doi:10.3762/bjnano.8.131

• without the need of a complex spinneret. It is a simple and versatile way to prepare nanofibers with hollow or multichannel structures [26]. More importantly, various inorganic nanofibers can be fabricated easily by ME-ES including TiO2, SiO2, ZrO2, SnO2, V2O5, GeO2 and Al2O3. A microemulsion system was

• et al. reported the fabrication of hierarchical TiO2 nanorods via ME-ES and the application as photoanode material for dye-sensitized solar cells [25]. According to Shi et al., highly porous SnO2/TiO2 composite nanofibers were prepared successfully by ME-ES and subsequent calcination [28]. There are

Metal oxide nanostructures: preparation, characterization and functional applications as chemical sensors

• Dario Zappa,
• Angela Bertuna,
• Elisabetta Comini,
• Navpreet Kaur,
• Nicola Poli,
• Veronica Sberveglieri and
• Giorgio Sberveglieri

Beilstein J. Nanotechnol. 2017, 8, 1205–1217, doi:10.3762/bjnano.8.122

• characterization of different metal oxide (NiO, WO3, ZnO, SnO2 and Nb2O5) nanostructures for chemical sensing are presented. p-Type (NiO) and n-type (WO3, SnO2, ZnO and Nb2O5) metal oxide nanostructures were grown on alumina substrates using evaporation–condensation, thermal oxidation and hydrothermal techniques

• nanostructures Evaporation–condensation technique: NiO, SnO2 and ZnO Evaporation–condensation allows one to obtain disordered mats of nanowires, covering the area of substrates with the catalyst. Figure 1 (top) shows the FE-SEM images of NiO nanowires at different magnifications, while Figure 1 (middle) and

• Figure 1 (bottom) report SnO2 nanowires and ZnO nanowires, respectively. Nanowires were directly grown on the active substrates used for functional characterization. It has been observed that the NiO nanowires were grown thin and long and they showed a dense morphology covering the whole substrate. The

Investigation of the photocatalytic efficiency of tantalum alkoxy carboxylate-derived Ta₂O₅ nanoparticles in rhodamine B removal

• Subia Ambreen,
• Mohammad Danish,
• Narendra D. Pandey and
• Ashutosh Pandey

Beilstein J. Nanotechnol. 2017, 8, 604–613, doi:10.3762/bjnano.8.65

• removal, sedimentation and filtration are not very effective in removing organic dyes. Advanced oxidation processes (AOPs) receive a lot of interest in this regard, and photocatalysis by semiconductors is the most extensively investigated AOP. Metal oxide nanoparticles (NPs), for example TiO2, ZnO, SnO2

Thin SnO_x films for surface plasmon resonance enhanced ellipsometric gas sensing (SPREE)

• Daniel Fischer,
• Andreas Hertwig,
• Uwe Beck,
• Volkmar Lohse,
• Detlef Negendank,
• Martin Kormunda and
• Norbert Esser

Beilstein J. Nanotechnol. 2017, 8, 522–529, doi:10.3762/bjnano.8.56

• 730 ECS, von Ardenne Anlagentechnik GmbH) with 13.56 MHz frequency and 200 W power. Here, a commercially available pure SnO2 target (99.9%) obtained from FHR GmbH was used. The target has a diameter of 200 mm and a thickness of 6 mm. For the Fe-doped samples, a home-built RF magnetron sputtering

• equipment with 13.56 MHz frequency was used with a SnO2 target (99.95%) of 48 mm diameter. In this case, an additional rectangular Fe-strip (99.95%) of size 10 mm × 20 mm and a thickness of 2 mm was attached at the center of the SnO2 target. The deposition was done by applying 50 W of DC pulsed power at a

Impact of air exposure and annealing on the chemical and electronic properties of the surface of SnO₂ nanolayers deposited by rheotaxial growth and vacuum oxidation

• Monika Kwoka and
• Maciej Krzywiecki

Beilstein J. Nanotechnol. 2017, 8, 514–521, doi:10.3762/bjnano.8.55

• Monika Kwoka Maciej Krzywiecki Institute of Electronics, Silesian University of Technology, Akademicka 16, 44-100 Gliwice, Poland Institute of Physics – CSE, Silesian University of Technology, Konarskiego 22B, 44-100 Gliwice, Poland 10.3762/bjnano.8.55 Abstract In this paper the SnO2 nanolayers

• photoelectron spectroscopy (XPS). The layers were tested i) pristine, ii) after air exposure and iii) after UHV annealing to validate perspective recovery procedures of the sensing layers. XPS results showed that the pristine RGVO SnO2 nanolayers are of high purity with a ratio [O]/[Sn] = 1.62 and almost no

• the distance between the valence band edge and the Fermi level energy. This was attributed to oxygen diffusion through the porous SnO2 surface as measured by atomic force microscopy. Keywords: Fermi level position; RGVO nanolayers; rheotaxial growth and vacuum oxidation (RGVO); surface chemistry; tin

Study of the surface properties of ZnO nanocolumns used for thin-film solar cells

• Neda Neykova,
• Jiri Stuchlik,
• Karel Hruska,
• Ales Poruba,
• Zdenek Remes and
• Ognen Pop-Georgievski

Beilstein J. Nanotechnol. 2017, 8, 446–451, doi:10.3762/bjnano.8.48

• -Si) solar cells, used for mass production, is composed of a transparent conductive oxide with roughness at the nanoscale on the front (TCO), e.g., tin oxide (SnO2) or zinc oxide (ZnO), followed by p–i–n Si layers (amorphous and/or nanocrystalline) in the cell and a back reflector [1][2]. In such a

Photocatalysis applications of some hybrid polymeric composites incorporating TiO₂ nanoparticles and their combinations with SiO₂/Fe₂O₃

• Andreea Laura Chibac,
• Tinca Buruiana,
• Violeta Melinte and
• Emil C. Buruiana

Beilstein J. Nanotechnol. 2017, 8, 272–286, doi:10.3762/bjnano.8.30

• than the other catalysts studied in literature (ZnO, SnO2, WO3, CdS) because of their superior redox ability and photoelectric properties, the long-term stability, the nontoxicity, and the low cost [10][11][12][13][14][15]. Nevertheless, the practical applications of TiO2 have a major drawback, namely

Nanocrystalline TiO₂/SnO₂ heterostructures for gas sensing

• Barbara Lyson-Sypien,
• Anna Kusior,
• Mieczylaw Rekas,
• Jan Zukrowski,
• Marta Gajewska,
• Katarzyna Michalow-Mauke,
• Thomas Graule,
• Marta Radecka and
• Katarzyna Zakrzewska

Beilstein J. Nanotechnol. 2017, 8, 108–122, doi:10.3762/bjnano.8.12

• Laboratories for Materials Testing and Research, Laboratory for High Performance Ceramics, Uberlandstrasse 129, 8600 Duebendorf, Switzerland Paul Scherrer Institut, 5232 Villigen PSI, Switzerland 10.3762/bjnano.8.12 Abstract The aim of this research is to study the role of nanocrystalline TiO2/SnO2 n–n

• heterojunctions for hydrogen sensing. Nanopowders of pure SnO2, 90 mol % SnO2/10 mol % TiO2, 10 mol % SnO2/90 mol % TiO2 and pure TiO2 have been obtained using flame spray synthesis (FSS). The samples have been characterized by BET, XRD, SEM, HR-TEM, Mössbauer effect and impedance spectroscopy. Gas-sensing

• experiments have been performed for H2 concentrations of 1–3000 ppm at 200–400 °C. The nanomaterials are well-crystallized, anatase TiO2, rutile TiO2 and cassiterite SnO2 polymorphic forms are present depending on the chemical composition of the powders. The crystallite sizes from XRD peak analysis are within

Nanostructured SnO₂–ZnO composite gas sensors for selective detection of carbon monoxide

• Paul Chesler,
• Cristian Hornoiu,
• Susana Mihaiu,
• Cristina Vladut,
• Jose Maria Calderon Moreno,
• Mihai Anastasescu,
• Carmen Moldovan,
• Bogdan Firtat,
• Costin Brasoveanu,
• George Muscalu,
• Ion Stan and
• Mariuca Gartner

Beilstein J. Nanotechnol. 2016, 7, 2045–2056, doi:10.3762/bjnano.7.195

• , 060021 Bucharest, Romania National Institute for Research and Development in Micro-technologies, 077190 Bucharest, Romania, Romelgen SRL, Bucharest, Romania 10.3762/bjnano.7.195 Abstract A series of SnO2–ZnO composite nanostructured (thin) films with different amounts of SnO2 (from 0 to 50 wt %) was

• . It was found that the sensing performance was influenced by the amount of oxide components present in the composite material. Improved sensing performance was achieved for the ZnO (98 wt %)–SnO2 (2 wt %) composite as compared to the sensors containing only the pristine oxides. The sensor response

• , cross-response and recovery characteristics of the analyzed materials are reported. The high sensitivity (RS = 1.21) to low amounts of CO (5 ppm) was reported for the sensor containing a composite sensitive film with ZnO (98 wt %)–SnO2 (2 wt %). This sensor response to CO was five times higher as