Synthesis and enhanced photocatalytic performance of 0D/2D CuO/tourmaline composite photocatalysts

• Changqiang Yu,
• Min Wen,
• Zhen Tong,
• Shuhua Li,
• Yanhong Yin,
• Xianbin Liu,
• Yesheng Li,
• Tongxiang Liang,
• Ziping Wu and
• Dionysios D. Dionysiou

Beilstein J. Nanotechnol. 2020, 11, 407–416, doi:10.3762/bjnano.11.31

• functional mineral material for accepting the photogenerated e− due to its special electric field. Herein, we report the successful synthesis of the CuO/tourmaline composite photocatalyst with 0D/2D CuO geometric structure by a facile precipitation–hydrothermal process. This work firstly highlights a simple

• ., China. Photocatalyst synthesis A hydrothermal process was employed to synthesize the CuO/tourmaline composite. In detail, 0.50 g of the tourmaline powder and 40 mL of distilled water were added into a beaker followed by 20 min of magnetic stirring, and the obtained suspension was sonicated for 20 min to

• NANO ZS90 instrument (Malvern, UK). Photocatalytic activity evaluation The photocatalytic performance was examined by the degradation of MB with light irradiation simulated by a 300 W Xe lamp with a 420 nm cut-off filter. In detail, 0.05 g of the as-synthesized photocatalyst was added into 100 mL of

Air oxidation of sulfur mustard gas simulants using a pyrene-based metal–organic framework photocatalyst

• Ghada Ayoub,
• Mihails Arhangelskis,
• Xuan Zhang,
• Florencia Son,
• Timur Islamoglu,
• Tomislav Friščić and
• Omar K. Farha

Beilstein J. Nanotechnol. 2019, 10, 2422–2427, doi:10.3762/bjnano.10.232

• an active photocatalyst, where the pyrene-based linkers are expected to play the role of photosensitizers responsible for singlet oxygen production under UV irradiation, several control studies were performed to firmly establish the role of the linker. We explored the ability of pure linker precursor

• , 3.4 mg) of the MOF, no conversion of CEES was detected (Figure 2), confirming the role of NU-400 as a photocatalyst. The photocatalytic activity of NU-400 in air, without oxygen presaturation, is significantly higher compared to the previously explored mesoporous NU-1000 MOF, which is based on a

• different, tetratopic pyrene-based linker 4,4’,4’’,4’’’-(pyrene-1,3,6,8-tetrayl)tetrabenzoate (H4TBApy). Using 1 mol % (5.2 mg) NU-1000 as a photocatalyst enabled the full conversion of CEES into CEESO with a half-life of only 6.2 minutes under conditions of O2 saturation. However, the process was

Improved adsorption and degradation performance by S-doping of (001)-TiO₂

• Xiao-Yu Sun,
• Xian Zhang,
• Xiao Sun,
• Ni-Xian Qian,
• Min Wang and
• Yong-Qing Ma

Beilstein J. Nanotechnol. 2019, 10, 2116–2127, doi:10.3762/bjnano.10.206

• -pyrroline-N-oxide (DMPO) were determined on a Bruker EMX plus 10/12 (equipped with Oxford ESR910 Liquid Helium cryostat). For detection of the superoxide radicals (•O2−) and hydroxyl radicals (•OH), 2.5 mg of the photocatalyst was dispersed in 1 mL DMPO/methyl alcohol solution or DMPO/H2O solution. The

Direct observation of oxygen-vacancy formation and structural changes in Bi₂WO₆ nanoflakes induced by electron irradiation

• Hong-long Shi,
• Bin Zou,
• Zi-an Li,
• Min-ting Luo and
• Wen-zhong Wang

Beilstein J. Nanotechnol. 2019, 10, 1434–1442, doi:10.3762/bjnano.10.141

• photocatalyst was dispersed into 100 mL of 10 mg/L MB solution. Then the suspensions were magnetically stirred for 1 h in the dark to ensure the establishment of an adsorption–desorption equilibrium between photocatalyst and MB. Then the solution was exposed to visible-light irradiation under magnetic stirring

BiOCl/TiO₂/diatomite composites with enhanced visible-light photocatalytic activity for the degradation of rhodamine B

• Minlin Ao,
• Kun Liu,
• Xuekun Tang,
• Zishun Li,
• Qian Peng and
• Jing Huang

Beilstein J. Nanotechnol. 2019, 10, 1412–1422, doi:10.3762/bjnano.10.139

• Abstract A BiOCl/TiO2/diatomite (BTD) composite was synthesized via a modified sol–gel method and precipitation/calcination method for application as a photocatalyst and shows promise for degradation of organic pollutants in wastewater upon visible-light irradiation. In the composite, diatomite was used as

• , low-cost and ease of application, which are superior to other approaches of environmental remediation [8][9]. However, the application of photocatalysis is still hindered due to the agglomeration of photocatalyst particles, the difficulty of photocatalyst recovery and low photocatalytic performance

• organic pollutant degradation [15]. However, according to previous studies, one limitation to its photocatalytic activity is that the photocatalytic process mainly occurs on the surface of the photocatalyst, which is a problem because the TiO2 nanoparticles readily agglomerate [10]. According to the

Construction of a 0D/1D composite based on Au nanoparticles/CuBi₂O₄ microrods for efficient visible-light-driven photocatalytic activity

• Weilong Shi,
• Mingyang Li,
• Hongji Ren,
• Feng Guo,
• Xiliu Huang,
• Yu Shi and
• Yubin Tang

Beilstein J. Nanotechnol. 2019, 10, 1360–1367, doi:10.3762/bjnano.10.134

• photocatalyst consisting of Au nanoparticles (NPs) and CuBi2O4 microrods (Au/CBO) was designed and prepared by a simple thermal reduction–precipitation approach. It shows excellent photocatalytic performance in the degradation of tetracycline (TC). The maximum photocatalytic degradation rate constant for Au/CBO

• affect the SPR of Au NPs. The Au NPs promote the rapid separation of charge carriers of semiconductor [10][26][27]. Thus, we attempt to use 0D Au NPs to decorate 1D CuBi2O4 (CBO) microrods to obtain a new type of efficient 0D/1D composite photocatalyst. Herein, 0D/1D Au NP/CBO microrod composites were

• separated by centrifuged with distilled water, dried at 60 °C for 12 h to obtain the final Au/CBO composite photocatalyst. The mass ratios between Au nanoparticles and CBO microrods were 1%, 1.5%, 2.5%, 3.5% and 5%, named as 1 wt % Au/CBO, 1.5 wt % Au/CBO, 2.5 wt % Au/CBO, 3.5 wt % Au/CBO and 5 wt % Au/CBO

Imaging the surface potential at the steps on the rutile TiO₂(110) surface by Kelvin probe force microscopy

• Masato Miyazaki,
• Huan Fei Wen,
• Quanzhen Zhang,
• Yuuki Adachi,
• Jan Brndiar,
• Ivan Štich,
• Yan Jun Li and
• Yasuhiro Sugawara

Beilstein J. Nanotechnol. 2019, 10, 1228–1236, doi:10.3762/bjnano.10.122

• steps in the catalytic reaction. Keywords: catalyst; Kelvin probe force microscopy; Smoluchowski effect; step; titanium dioxide; Introduction Titanium dioxide (TiO2) has attracted considerable interest for its promising applications as a photocatalyst and as catalyst support, as well as in gas sensors

A highly efficient porous rod-like Ce-doped ZnO photocatalyst for the degradation of dye contaminants in water

• Binjing Hu,
• Qiang Sun,
• Chengyi Zuo,
• Yunxin Pei,
• Siwei Yang,
• Hui Zheng and
• Fangming Liu

Beilstein J. Nanotechnol. 2019, 10, 1157–1165, doi:10.3762/bjnano.10.115

• , Parkville, Victoria 3010, Australia ARC Centre of Excellence for Nanoscale BioPhotonics (CNBP), School of Science, RMIT University, Melbourne, VIC 3001, Australia 10.3762/bjnano.10.115 Abstract A mild and simple method was developed to synthesize a highly efficient photocatalyst comprised of Ce-doped ZnO

• microstructure. The computational results showed that the dipole-like field covers the entire surface of the rod-like Ce-doped ZnO photocatalyst and is present over the entire range of wavelengths considered. The optimum degradation conditions were determined by orthogonal tests and range analysis, including the

• ) = 10 mg/L, concentration (catalyst) = 0.7 g/L, pH 9.0 and T = 50 °C. These optimum conditions supply a helpful reference for large-scale wastewater degradation containing the common water contaminant RhB. Keywords: Ce-doped ZnO; photocatalyst; rhodamine B; solar degradation; surface shape

Photoactive nanoarchitectures based on clays incorporating TiO₂ and ZnO nanoparticles

• Eduardo Ruiz-Hitzky,
• Pilar Aranda,
• Marwa Akkari,
• Nithima Khaorapapong and
• Makoto Ogawa

Beilstein J. Nanotechnol. 2019, 10, 1140–1156, doi:10.3762/bjnano.10.114

• NPs immobilization as well as on the structural stability during the photocatalytic reactions. In addition, the immobilization of NPs on clay surfaces is a key advantage for the easier recovery of the photocatalyst from the reaction medium compared to bare NPs [88][89][90][91][92][93]. Clay-based

• 2.25 eV, corresponding to a light wavelength of 550 nm suitable for a photocatalyst responsive to visible light was reported. The co-doping of N and S [149] and Cu, Ag, and Fe on TiO2@bentonite has also been reported [150]. Other authors also reported the modification of the photoactivity

• additional of ZnO providing a higher photocatalytic activity to the starting clay or the TiO2@clay nanoarchitecture. Related ZnO–TiO2@clay materials based on commercially available expanded clay aggregates (LECA), apparently belonging to the smectite family, have been also positively tested as photocatalyst

Synthesis of novel C-doped g-C₃N₄ nanosheets coupled with CdIn₂S₄ for enhanced photocatalytic hydrogen evolution

• Jingshuai Chen,
• Chang-Jie Mao,
• Helin Niu and
• Ji-Ming Song

Beilstein J. Nanotechnol. 2019, 10, 912–921, doi:10.3762/bjnano.10.92

• photogenerated holes and electrons. Yang et al. designed and constructed a 2D/2D nanocomposite photocatalyst through the in situ generation of ZnIn2S4 nanoleaf structures on the surface of g-C3N4 nanosheets by a facile one-step solvothermal method with surfactant, which exhibited distinct high-speed charge

• the CCN surface, resulting in close contact (Figure 4c,d). X-ray photoelectron spectroscopy (XPS) was utilized to study the surface elemental composition of the representative composite photocatalyst CISCCN3. The survey XPS spectrum of Figure 5a shows that the CISCCN3 composite is mostly composed of C

• over CISCCN3 composites is remarkably facilitated. In addition, a further decrease in the PL emission intensity in the CISCCN3 hybrid photocatalyst can be observed. This result demonstrates that the construction of a heterogeneous interface can improve the separation and transfer of photogenerated

Reduced graphene oxide supported C₃N₄ nanoflakes and quantum dots as metal-free catalysts for visible light assisted CO₂ reduction

• Md Rakibuddin and
• Haekyoung Kim

Beilstein J. Nanotechnol. 2019, 10, 448–458, doi:10.3762/bjnano.10.44

• promising for CO2 photoreduction because of their excellent activity and environmental sustainability. Keywords: CO2 reduction; metal-free hybrid; nanoflakes; photocatalyst; quantum dots; Introduction The solar-light-assisted photocatalytic reduction of CO2 into useful chemicals, such as HCOOH, HCHO, CH4

• of photo-induced electron–hole pairs and insufficient adsorption of CO2 at the catalyst surface are crucial problems preventing effective catalyst performance and CO2 reduction [11]. An ideal photocatalyst for CO2 conversion should possess a narrow bandgap and good light-harvesting properties, proper

Development of an anti-pollution coating process technology for the application of an on-site PV module

• Sejin Jung,
• Wonseok Choi,
• Jung Hyun Kim and
• Jang Myoun Ko

Beilstein J. Nanotechnol. 2019, 10, 332–336, doi:10.3762/bjnano.10.32

• natural water will significantly improve the economic efficiency of the maintenance of solar power generation systems [7]. Although a self-cleaning coating technique using a photocatalyst has been developed, the durability is poor due to low adhesion and hardness. Also, production is very difficult, an

Graphene-enhanced metal oxide gas sensors at room temperature: a review

• Dongjin Sun,
• Yifan Luo,
• Marc Debliquy and
• Chao Zhang

Beilstein J. Nanotechnol. 2018, 9, 2832–2844, doi:10.3762/bjnano.9.264

• dioxide (TiO2), as a wide-bandgap semiconductor, has been widely used as photocatalyst, and in solar cells and gas sensors [70][71][72]. In general, its operating temperature is over 200 °C, so scholars try to prepare composites with graphene to reduce its operating temperature. However, the stability of

Nanocellulose: Recent advances and its prospects in environmental remediation

• Katrina Pui Yee Shak,
• Yean Ling Pang and
• Shee Keat Mah

Beilstein J. Nanotechnol. 2018, 9, 2479–2498, doi:10.3762/bjnano.9.232

• by the action of bacteria. In this review, some invigorating perspectives on the challenges, future direction, and updates on the most relevant uses of nanocellulose in environmental remediation are discussed. The reported applications and properties of nanocellulose as an adsorbent, photocatalyst

• in an effort to improve the development and efficient use of nanocellulose in environmental remediation. Keywords: adsorbent; environmental remediation; membrane; nanocellulose; nanomaterials; photocatalyst; Review Introduction The rampant emergence of advanced, new nanomaterials is redefining many

• nanocellulose-based materials used in various applications under the category of environmental remediation, including past achievements, current advances, and potential directions. The recent developments of nanocellulose used as an adsorbent, photocatalyst, flocculant or membrane for various applications in

Hierarchical heterostructures of Bi₂MoO₆ microflowers decorated with Ag₂CO₃ nanoparticles for efficient visible-light-driven photocatalytic removal of toxic pollutants

• Shijie Li,
• Wei Jiang,
• Shiwei Hu,
• Yu Liu,
• Yanping Liu,
• Kaibing Xu and
• Jianshe Liu

Beilstein J. Nanotechnol. 2018, 9, 2297–2305, doi:10.3762/bjnano.9.214

• regarded as a promising visible-light-driven (VLD) photocatalyst because of its good activity, chemical stability and nontoxicity [15][16][17]. However, the low carrier-separation rate and narrow photo-response range of Bi2MoO6 substantially lower its photocatalytic performance [18][19]. To overcome this

• degradation. Conclusion We synthesized a novel photocatalyst of Bi2MoO6 microflowers covered with Ag2CO3 nanoparticles by a facile procedure. The Ag2CO3/Bi2MoO6 heterostructures, especially ACO/BMO-30, showed a substantially enhanced photocatalytic performance in the removal of pollutants (RhB, MO, MB and TC

• efficient VLD photocatalyst with promising applications in environmental remediation. Experimental Materials Bi(NO3)3·5H2O, NaHCO3, NH3·H2O, Na2MoO4·2H2O, rhodamine B (RhB), methyl blue (MB), tetracycline hydrochloride (TC), methyl orange (MO), isopropanol (IPA), AgNO3, p-benzoquinone (BQ), and ammonium

Controllable one-pot synthesis of uniform colloidal TiO₂ particles in a mixed solvent solution for photocatalysis

• Jong Tae Moon,
• Seung Ki Lee and
• Ji Bong Joo

Beilstein J. Nanotechnol. 2018, 9, 1715–1727, doi:10.3762/bjnano.9.163

• Honda and Fujishima [12]. Over the past decade, there have been many attempts to fabricate highly active TiO2-based photocatalysts for enhanced photocatalytic efficiency [13][14][15][16][17]. It is well-known that photocatalysis over a semiconductor photocatalyst occurs in the following sequential steps

• . First, the semiconductor photocatalyst can absorb photon energy that is greater than its band gap and electrons in the valance band can be exited to the conduction band, resulting in photoexcited electron–hole pairs. Then, the photo-exited electron–hole can move to the surface of the photocatalyst

• photocatalyst must be narrow in order to facilitate the facile adsorption of the low energy photon and high harvesting efficiency under visible-light irradiation conditions [11]. To enhance charge separation efficiency and extend the lifetime of photoexcited electron–hole pairs, properties such as a crystalline

Sulfur-, nitrogen- and platinum-doped titania thin films with high catalytic efficiency under visible-light illumination

• Boštjan Žener,
• Lev Matoh,
• Giorgio Carraro,
• Bojan Miljević and
• Romana Cerc Korošec

Beilstein J. Nanotechnol. 2018, 9, 1629–1640, doi:10.3762/bjnano.9.155

• rather there exists an optimal particle size for pure nanocrystalline TiO2 [19]. This is due to surface recombination of electron–hole pairs in samples with particle sizes smaller than 6 nm. One of the main drawbacks of using TiO2 as a photocatalyst is the width of its band gap (3.2 eV), which means the

• the form of a thin film significantly reduces some of the drawbacks of the practical application of heterogeneous photocatalysis; for instance, the need to separate the photocatalyst from the suspension after the photocatalytic reaction, or the tendency of the particles to agglomerate in aqueous

Sheet-on-belt branched TiO₂(B)/rGO powders with enhanced photocatalytic activity

• Huan Xing,
• Wei Wen and
• Jin-Ming Wu

Beilstein J. Nanotechnol. 2018, 9, 1550–1557, doi:10.3762/bjnano.9.146

• constant of the present “sheet-on-belt” branched TiO2(B)/rGO photocatalyst is 1.7 times that of TiO2(B)/rGO and 2.9 times that of pristine TiO2(B) nanobelts. Experimental Material synthesis 1. Precursor solution: The precursor solution for precipitation of nanosheet branches was prepared following Wen et

• excitation wavelength of 360 nm. Photocatalytic activity The photocatalytic activity of the TGN and branched TGN powders were evaluated by photodegradation of phenol in water under UV light illumination. In a typical procedure, 25 mg of the photocatalyst was added to 50 mL of 10 ppm phenol aqueous solution

Cr(VI) remediation from aqueous environment through modified-TiO₂-mediated photocatalytic reduction

• Rashmi Acharya,
• Brundabana Naik and
• Kulamani Parida

Beilstein J. Nanotechnol. 2018, 9, 1448–1470, doi:10.3762/bjnano.9.137

• TiO2 as a photocatalyst and the importance of its modification for photocatalytic reduction of Cr(VI) has also been addressed. In this review, the photocatalytic activity of TiO2 after modification with carbon-based advanced materials, metal oxides, metal sulfides and noble metals towards reduction of

• surface of the semiconductor. When photons with energy greater than the band gap energy of the semiconductor photocatalyst (SP) are absorbed, photogenerated electrons are excited to conduction band (CB) leaving behind holes at the valence band (VB) as per Equation 1: These photogenerated species

• widely been accepted by the research community as a green photocatalyst [75]. Irradiation using UV light on TiO2 results in the formation of eCB− and hVB+ at its CB and VB, respectively. The eCB− reduces Cr(VI) species to Cr(III) as per Equation 10 and hVB+ oxidizes water to O2 (Equation 11). In some

Ag₂WO₄ nanorods decorated with AgI nanoparticles: Novel and efficient visible-light-driven photocatalysts for the degradation of water pollutants

• Shijie Li,
• Shiwei Hu,
• Wei Jiang,
• Yanping Liu,
• Yu Liu,
• Yingtang Zhou,
• Liuye Mo and
• Jianshe Liu

Beilstein J. Nanotechnol. 2018, 9, 1308–1316, doi:10.3762/bjnano.9.123

• . The active species trapping experiment reveals that active species (O2•− and h+) dominantly contribute to RhB degradation. The AgI/Ag2WO4 heterojunction photocatalyst characterized in this work holds great potential for remedying environmental issues due to its simple preparation method and excellent

• Ag2S/Ag2WO4 [40], C3N4/Ag2WO4 [39], Bi2MoO6/Ag2WO4/Ag [42] etc., have been reported to show improved VLD performance in the degradation of pollutants. To the best of our knowledge, application of AgI/Ag2WO4 as a VLD photocatalyst for the degradation of toxic pollutants remains unreported. In this study

• the CB of AgI (and more holes left behind in the valence band (VB)) could readily attack the pollutant molecules, resulting in the remarkable photocatalytic performance of AgI/Ag2WO4. Conclusion In summary, a novel heterojunction photocatalyst comprised of AgI nanoparticle-decorated Ag2WO4 nanorods

Noble metal-modified titania with visible-light activity for the decomposition of microorganisms

• Maya Endo,
• Zhishun Wei,
• Kunlei Wang,
• Baris Karabiyik,
• Kenta Yoshiiri,
• Paulina Rokicka,
• Bunsho Ohtani,
• Agata Markowska-Szczupak and
• Ewa Kowalska

Beilstein J. Nanotechnol. 2018, 9, 829–841, doi:10.3762/bjnano.9.77

• be used for photocatalyst activation [20]. Titanium(IV) oxide (titania) is the most widely used semiconductor photocatalyst used in treatment of water/wastewater and air [21]. The major barrier for common application of titania photocatalysis is the low activity under solar radiation (mainly due to

• light action [61][62][63]. In this mechanism, the photocatalyst properties such as particle shape, size and content of NPs could influence the efficiency on interaction between NPs and bacteria [64]. To evaluate the difference between dark activity and plasmonic photocatalysis, decomposition of

• bacterial cells in titania suspension with simultaneous measurements of evolved carbon dioxide was studied for bare and modified titania with gold or silver. Our preliminary studies on TiO2(ST41) photocatalyst showed that although inactivation of bacterial cells was similar for bare and silver-modified

Facile synthesis of a ZnO–BiOI p–n nano-heterojunction with excellent visible-light photocatalytic activity

• Mengyuan Zhang,
• Jiaqian Qin,
• Pengfei Yu,
• Bing Zhang,
• Mingzhen Ma,
• Xinyu Zhang and
• Riping Liu

Beilstein J. Nanotechnol. 2018, 9, 789–800, doi:10.3762/bjnano.9.72

• . Recently, bismuth oxyhalides have been proposed as a new kind of narrow band gap p-type semiconductor photocatalyst material whose general formula is BiOX, where X represents Cl, Br or I. They crystallize in the tetragonal matlockite structure with space group P4/NMMS. In the crystal structure of all these

• response to visible light. Though widely investigated, BiOI suffers from its high recombination rate of photoinduced electron–holes and low charge transfer ability. Therefore, the strategies to improve the efficiency of this kind of semiconductor photocatalyst are in need. Heterogeneous processes are

• . described the synthesis of p–n heterostructures where p-type BiOI nanoplates decorated on n-type ZnO nanorod arrays which were synthesized through a solvothermal route. The high-contact areas provided by the fast charge transfer channel of BiOI and ZnO create the efficient photocatalyst [35]. Tong et al

Surface-plasmon-enhanced ultraviolet emission of Au-decorated ZnO structures for gas sensing and photocatalytic devices

• T. Anh Thu Do,
• Truong Giang Ho,
• Thu Hoai Bui,
• Quang Ngan Pham,
• Hong Thai Giang,
• Thi Thu Do,
• Duc Van Nguyen and
• Dai Lam Tran

Beilstein J. Nanotechnol. 2018, 9, 771–779, doi:10.3762/bjnano.9.70

• . Keywords: Au-decorated ZnO; carrier dynamics; gas sensors; photocatalyst; SPR effect; Introduction Inorganic transition metal oxide sensor devices have attracted attention in particular for improving gas sensing, energy conversion, electronics, photocatalysis and optoelectronic devices [1][2][3][4]. Among

• ultrasonicated for 5 min to make the homogeneous distribution of photocatalyst with RhB. Before light irradiation, the cell containing the photocatalyst and the aqueous RhB solution was kept in the dark for 40 min to reach an adsorption/desorption equilibrium between the photocatalyst and RhB molecules. The RhB

• . The photocatalytic decomposition of RhB molecules is evaluated by the PL quenching of the RhB in the photocatalyst-mixed solution. The percentage of the PL quenching is calculated by the ratio of integrating the measured PL emission from 500–700 nm. XRD patterns (a), FE-SEM images of as-deposited ZnO

Combined pulsed laser deposition and non-contact atomic force microscopy system for studies of insulator metal oxide thin films

• Daiki Katsube,
• Hayato Yamashita,
• Satoshi Abo and
• Masayuki Abe

Beilstein J. Nanotechnol. 2018, 9, 686–692, doi:10.3762/bjnano.9.63

• oxides, and studies at the atomic level of both materials are still ongoing because of their high importance in materials science. Anatase TiO2 is well known as a photocatalyst, but there have been few studies using NC-AFM due to the difficulty in preparing samples [58]. Thin films of LaAlO3 epitaxially

Perovskite-structured CaTiO₃ coupled with g-C₃N₄ as a heterojunction photocatalyst for organic pollutant degradation

• Ashish Kumar,
• Christian Schuerings,
• Suneel Kumar,
• Ajay Kumar and
• Venkata Krishnan

Beilstein J. Nanotechnol. 2018, 9, 671–685, doi:10.3762/bjnano.9.62

• )–CaTiO3 (CTCN) organic–inorganic heterojunction photocatalyst was synthesized by a facile mixing method, resulting in the deposition of CaTiO3 (CT) nanoflakes onto the surface of g-C3N4 nanosheets. The photocatalytic activity of the as-synthesized heterojunction (along with the controls) was evaluated by

• degradation of pollutants has been proposed and discussed. Keywords: CaTiO3; graphitic carbon nitride (g-C3N4); heterojunction photocatalyst; pollutant degradation; Introduction Photocatalysis is recognized as an attractive approach for environmental remediation and energy generation applications due to its

• potential towards utilization of solar energy [1][2][3]. Therefore, extensive efforts have been made for the design and synthesis of highly efficient and stable photocatalyst systems over the past few decades [4][5][6][7]. Hence, the development of such photocatalysts with high stability and good activity