Seebeck coefficient of silicon nanowire forests doped by thermal diffusion

• Shaimaa Elyamny,
• Elisabetta Dimaggio and
• Giovanni Pennelli

Beilstein J. Nanotechnol. 2020, 11, 1707–1713, doi:10.3762/bjnano.11.153

• sustainable. Silicon has a very high power factor S2σ [1][2][3][4] (S is the Seebeck coefficient and σ is the electrical conductivity). This, combined with the reduced thermal conductivity when nanostructured [5][6][7][8][9][10], makes it very suitable for thermoelectric applications. As added value, silicon

• fabricated on the top of a silicon nanowire forest, which can be achieved by copper electrodeposition [18]. 2) The optimum doping concentration of the nanowires for the exploitation of the maximum power factor of silicon [3] needs to be found. Both the Seebeck coefficient and the electrical conductivity

• depend on the doping concentration. In particular, S decreases with increasing doping concentrations. At the same time, high doping concentrations yield high values of electrical conductivity σ. Hence, a trade-off between S and σ needs to be found, such that the product S2σ is maximized. Nanowires with

One-step synthesis of carbon-supported electrocatalysts

• Sebastian Tigges,
• Nicolas Wöhrl,
• Ivan Radev,
• Ulrich Hagemann,
• Markus Heidelmann,
• Thai Binh Nguyen,
• Stanislav Gorelkov,
• Stephan Schulz and
• Axel Lorke

Beilstein J. Nanotechnol. 2020, 11, 1419–1431, doi:10.3762/bjnano.11.126

• discussed in the following. Traditional multistep synthesis methods for Pt/C catalysts use supports, which are partially graphitized for reaching the required high electrical conductivity and durability. Therefore, the support surface is characterized by a low density of binding sites for anchoring Pt-NP

• , on which the Pt-NPs can then easily diffuse. Hence, these supports often require additional functionalization steps for avoiding metal particle agglomeration, which reduces the electrical conductivity and durability of the support. In sharp contrast, the one-step synthesis of Pt/CNW presented herein

Effect of localized helium ion irradiation on the performance of synthetic monolayer MoS₂ field-effect transistors

• Jakub Jadwiszczak,
• Pierce Maguire,
• Conor P. Cullen,
• Georg S. Duesberg and
• Hongzhou Zhang

Beilstein J. Nanotechnol. 2020, 11, 1329–1335, doi:10.3762/bjnano.11.117

• Technology, Universität der Bundeswehr München, Werner-Heisenberg-Weg 39, 85577 Neubiberg, Germany 10.3762/bjnano.11.117 Abstract Helium ion irradiation is a known method of tuning the electrical conductivity and charge carrier mobility of novel two-dimensional semiconductors. Here, we report a systematic

• cm−2 [13][14][15][16][17], as well as good electrical conductivity for up to approx. 1018 ions cm−2 [9][10][18]. Sulfur vacancies (SVs) and the formation of a dislocation–divacancy complex can lead to significant n-doping in MoS2 [19], which shifts the threshold voltage (Vth) of the FET to higher

Magnetohydrodynamic stagnation point on a Casson nanofluid flow over a radially stretching sheet

• Ganji Narender,
• Kamatam Govardhan and
• Gobburu Sreedhar Sarma

Beilstein J. Nanotechnol. 2020, 11, 1303–1315, doi:10.3762/bjnano.11.114

• generation, DT is the thermophoresis diffusion coefficient, σ is the electrical conductivity, β represents the Casson fluid parameter, and T represents the nanofluid temperature. The following similarity variables are taken into consideration: Finally, the ODEs describing the proposed flow problem can be

Structure and electrochemical performance of electrospun-ordered porous carbon/graphene composite nanofibers

• Yi Wang,
• Yanhua Song,
• Chengwei Ye and
• Lan Xu

Beilstein J. Nanotechnol. 2020, 11, 1280–1290, doi:10.3762/bjnano.11.112

• electrical conductivity and good biocompatibility [28][29][30]. Studies have indicated that graphene still maintains an excellent charge/discharge performance at an electrochemical scan rate of almost 250 mV·s−1 [31] and has an excellent cycle performance and fast charge/discharge characteristics [32

• electrode electrospinning method (MPEM). It was found that the alignment of the composite nanofibers (CNFs) improved their electrical conductivity. Therefore, this study provided a convenient and straightforward approach to synthesize ordered porous carbon/graphene CNFs (CGCNFs) with a high number of

• specific surface area. The increase in the specific surface area of the electrode due to increased porosity facilitates ion transportation, which increases the conductivity of monolithic electrodes [24][25][26]. Although the porous carbon nanofibers have a high specific surface area, their low electrical

A few-layer graphene/chlorin e6 hybrid nanomaterial and its application in photodynamic therapy against Candida albicans

• Selene Acosta,
• Carlos Moreno-Aguilar,
• Dania Hernández-Sánchez,
• Beatriz Morales-Cruzado,
• Erick Sarmiento-Gomez,
• Carla Bittencourt,
• Luis Octavio Sánchez-Vargas and
• Mildred Quintana

Beilstein J. Nanotechnol. 2020, 11, 1054–1061, doi:10.3762/bjnano.11.90

• GO (rGO) [22]. GO and rGO have been conjugated to several photosensitizers to enhance their performance in PDT [15][17][23][24][25]. However, for enhancing the characteristics of a Ps, the properties of graphene, such as electrical conductivity and chemical stability are very important, and these

Gas-sensing features of nanostructured tellurium thin films

• Dumitru Tsiulyanu

Beilstein J. Nanotechnol. 2020, 11, 1010–1018, doi:10.3762/bjnano.11.85

• different operating temperatures with respect to scanning electron microscopy and X-ray diffraction analyses. It was shown that both types of films interacted with nitrogen dioxide, which resulted in a decrease of electrical conductivity. The gas sensitivity, as well as the response and recovery times

• with an approximate average size of 100 nm. Assuming the neutrality of the Au/Te contacts, the electrical conductivity of the film is mainly controlled by the bulk, surface and grain boundary resistances. On the other hand, due to the peculiarities of chalcogens and chalcogenide materials [1][30], a

Effect of magnetic field, heat generation and absorption on nanofluid flow over a nonlinear stretching sheet

• Santoshi Misra and
• Govardhan Kamatam

Beilstein J. Nanotechnol. 2020, 11, 976–990, doi:10.3762/bjnano.11.82

• expansion coefficient, ρp is the particle density, σ denotes the nanofluid electrical conductivity, B0 denotes the magnetic induction, vw denotes the suction/injection velocity and Q0 (Q) denotes the heat generation (absorption) coefficient. us in Equation 8 represents the slip velocity, given as which is

Structural optical and electrical properties of a transparent conductive ITO/Al–Ag/ITO multilayer contact

• Aliyu Kabiru Isiyaku,
• Ahmad Hadi Ali and
• Nafarizal Nayan

Beilstein J. Nanotechnol. 2020, 11, 695–702, doi:10.3762/bjnano.11.57

• roughness is attributed to the increasing grain sizes [35]. The large grain sizes of IAAI films reduce the number of grain boundaries and thus the scattering at grain boundaries. This improves the carrier mobility leading to an increased electrical conductivity of the films. The surface morphology of the

Preparation, characterization and photocatalytic performance of heterostructured CuO–ZnO-loaded composite nanofiber membranes

• Wei Fang,
• Liang Yu and
• Lan Xu

Beilstein J. Nanotechnol. 2020, 11, 631–650, doi:10.3762/bjnano.11.50

• widely used to fabricate nanofiber membranes because of its good spinnability, electrical conductivity, and heat resistance. However, carbonized PAN nanofiber membranes usually have poor mechanical properties. Polyvinylidene fluoride (PVDF) has better mechanical properties but a lower melting point

Comparison of fresh and aged lithium iron phosphate cathodes using a tailored electrochemical strain microscopy technique

• Matthias Simolka,
• Hanno Kaess and
• Kaspar Andreas Friedrich

Beilstein J. Nanotechnol. 2020, 11, 583–596, doi:10.3762/bjnano.11.46

• additional mechanical (stiffness, elasticity), electrical (conductivity, surface potential), electrochemical (reactivity, mobility and activity), mechanoelectrical (piezoelectricity) and chemical (chemical bonding) material properties. In situ AFM imaging of the sample topography is often used to study the

High-performance asymmetric supercapacitor made of NiMoO₄ nanorods@Co₃O₄ on a cellulose-based carbon aerogel

• Meixia Wang,
• Jing Zhang,
• Xibin Yi,
• Benxue Liu,
• Xinfu Zhao and
• Xiaochan Liu

Beilstein J. Nanotechnol. 2020, 11, 240–251, doi:10.3762/bjnano.11.18

• considered an ideal supporting material to hybridize with electroactive materials because of its low cost, easy fabrication, large surface area, interconnected porosity and high electrical conductivity [30][31]. Due to its micro/mesoporous 3D morphology with large open pores, it offers more space to grow

• excellent electrical conductivity and the 3D carbon nanonetwork. Secondly, NiMoO4 nanorods with extremely high specific capacitance are considered ideal spots for the nucleation and the growth of ZIF-67 particles. Lastly, the Co3O4 particles derived from ZIF-67 possess a nest-like structure and a porous

• the NiMoO4@Co3O4/CA composite of 1.3 Ω. This value is smaller than that of the Co3O4 particles derived from ZIF-67 with 1.5 Ω, demonstrating that the electrical conductivity is enhanced upon to the introduction of NiMoO4/CA. The cyclic stability of NiMoO4@Co3O4/CA was tested over 5000 cycles at 0.5 A

Size effects of graphene nanoplatelets on the properties of high-density polyethylene nanocomposites: morphological, thermal, electrical, and mechanical characterization

• Tuba Evgin,
• Alpaslan Turgut,
• Georges Hamaoui,
• Zdenko Spitalsky,
• Nicolas Horny,
• Matej Micusik,
• Mihai Chirtoc,
• Mehmet Sarikanat and
• Maria Omastova

Beilstein J. Nanotechnol. 2020, 11, 167–179, doi:10.3762/bjnano.11.14

• scanning electron microscope (SEM) images. Our results show that the lateral size of GnPs was a more regulating factor for the above-mentioned nanocomposite properties compared to their thickness. For a given lateral size, thinner GnPs showed significantly higher electrical conductivity and a lower

• superior inherent properties, such as its thermal (1000–5000 W/mK [5]) and electrical conductivity (6000 S/cm [6]), and mechanical properties (a Young’s modulus of 1 TPa and a tensile strength of 130 GPa [7]). However, the mass production of graphene with high quality at a low cost is still challenging

• the GnPs had only a slight effect on the reflection peaks of the HDPE/GnP nanocomposites, but the peak’s intensity was influenced stronger. Electrical conductivity Figure 4a–c demonstrate the AC conductivity (σ´AC) of all HDPE/GnP nanocomposites, measured at room temperature as a function of frequency

Molecular architectonics of DNA for functional nanoarchitectures

• Debasis Ghosh,
• Lakshmi P. Datta and
• Thimmaiah Govindaraju

Beilstein J. Nanotechnol. 2020, 11, 124–140, doi:10.3762/bjnano.11.11

• improve the detection sensitivity for mercury, which involved the thermodynamically and entropically favored displacement of BNA owing to the formation of metallo-DNA duplexes (dT–Hg–dT)n (Figure 5a). The displacement of BNA caused significant changes in the morphological, chiroptical, and electrical

• conductivity properties of the system, which was used for the dual-responsive detection of ultralow concentrations (subnanomolar level) of mercury. The BNAn–dTn coassembly material was used to fabricate a field-effect transistor (FET) for the detection of mercury (Figure 5c). Remarkably, both chiroptical and

Simple synthesis of nanosheets of rGO and nitrogenated rGO

• Pallellappa Chithaiah,
• Madhan Mohan Raju,
• Giridhar U. Kulkarni and
• C. N. R. Rao

Beilstein J. Nanotechnol. 2020, 11, 68–75, doi:10.3762/bjnano.11.7

• electrical conductivity obtained for H-rGO is ca. 0.068 S/m. Conclusion In conclusion, we present a very simple and efficient method for the successful synthesis of nanosheets of rGO and of rGO with high nitrogen content by the thermal decomposition of sucrose and glycine. We measured the specific

Synthesis of amorphous and graphitized porous nitrogen-doped carbon spheres as oxygen reduction reaction catalysts

• Maximilian Wassner,
• Markus Eckardt,
• Andreas Reyer,
• Thomas Diemant,
• Michael S. Elsaesser,
• R. Jürgen Behm and
• Nicola Hüsing

Beilstein J. Nanotechnol. 2020, 11, 1–15, doi:10.3762/bjnano.11.1

• meso- and macropores is beneficial for the ORR activity [11]. Finally, a higher degree of graphitization generally leads to an improved electrical conductivity, which should improve the overall ORR activity. On the other hand, it may alter also the properties of the active sites, which may be either

Mobility of charge carriers in self-assembled monolayers

• Zhihua Fu,
• Tatjana Ladnorg,
• Hartmut Gliemann,
• Alexander Welle,
• Asif Bashir,
• Michael Rohwerder,
• Qiang Zhang,
• Björn Schüpbach,
• Andreas Terfort and
• Christof Wöll

Beilstein J. Nanotechnol. 2019, 10, 2449–2458, doi:10.3762/bjnano.10.235

• a top electrode. We were able to determine a relationship between island size and electrical conductivity, and from this dependence, we could obtain information on the lateral charge transport and charge carrier mobility within the thin OSC layers. Our study demonstrates that AFM nanografting of

• length of the two SAM-forming molecules (1.68 nm for PAT, according to van der Waals structures [39] and 2.3 nm for the HDT [40]). The electrical conductivity as determined from the I–V-curves measured with the conductive probe AFM increases with the calculated diameter of the PAT islands (Figure 2d

Multiwalled carbon nanotube based aromatic volatile organic compound sensor: sensitivity enhancement through 1-hexadecanethiol functionalisation

• Nadra Bohli,
• Meryem Belkilani,
• Juan Casanova-Chafer,
• Eduard Llobet and
• Adnane Abdelghani

Beilstein J. Nanotechnol. 2019, 10, 2364–2373, doi:10.3762/bjnano.10.227

• toluene for various vapour concentrations injected at room temperature. The results show an increasing resistance with increasing concentration of the injected vapours. The adsorption of these vapours on the Au-MWCNT films leads to a reduction of the global sensor electrical conductivity. The lowest

• VOCs Figure 5 shows the response of the HDT/Au-MWCNT sensor to the varying benzene and toluene vapour concentrations injected at room temperature. The detection results of the various injected vapours show a considerable decrease in the electrical conductivity of the HDT/Au-MWCNT sensor compared with

Ultrathin Ni_1−xCo_xS₂ nanoflakes as high energy density electrode materials for asymmetric supercapacitors

• Xiaoxiang Wang,
• Teng Wang,
• Rusen Zhou,
• Lijuan Fan,
• Shengli Zhang,
• Feng Yu,
• Tuquabo Tesfamichael,
• Liwei Su and
• Hongxia Wang

Beilstein J. Nanotechnol. 2019, 10, 2207–2216, doi:10.3762/bjnano.10.213

• electrical conductivity. Developing ultrathin nanostructured materials is critical to achieving high electrochemical performance, because they possess rich active sites for electrochemical reactions, shortening the transport path of ions in the electrolyte during the charge/discharge processes. This paper

• from both nickel and cobalt ions in the bimetallic sulfides can provide relatively affluent redox reactions, resulting in higher specific capacitance and electrical conductivity [6][7]. Moreover, layered ultrathin nanoflakes in the synthesised nanomaterials, derived from metal oxides/dichalcogenides

• (TMDs), are attractive as energy-storage electrode materials. This is because the ultrathin structures are fully exposed to the active sites, leading to high electrical conductivity [8][9][10]. In previous reports, Ni–Co chalcogenides have always been combined with carbon-based materials such as

Improvement of the thermoelectric properties of a MoO₃ monolayer through oxygen vacancies

• Wenwen Zheng,
• Wei Cao,
• Ziyu Wang,
• Huixiong Deng,
• Jing Shi and
• Rui Xiong

Beilstein J. Nanotechnol. 2019, 10, 2031–2038, doi:10.3762/bjnano.10.199

• measured by a figure of merit (ZT) defined as ZT = S2σT/κ, where S, σ, T and κ represent the Seebeck coefficient, electrical conductivity, temperature and thermal conductivity, respectively [2][3]. In the past decade, great efforts have been made to boost the capabilities of thermoelectric materials

• [7] and Li-ion batteries [8][9][10][11]. Like most TMOs, bulk MoO3 has a wide band gap (about 3.0 eV) and low electrical conductivity, which seems inappropriate for thermoelectric devices. However, the electrical properties (including band gap and conductivity) of MoO3 are strongly dependent on the

• concentration of O vacancy concentrations. Hydrogen-ion intercalation [12] and solar-light irradiation [13] can turn MoO3 into MoO3−x and hence increase the electrical conductivity. Understanding the effect of O vacancies in MoO3 is very beneficial for its thermoelectric applications. Moreover, low-dimensional

Nanostructured and oriented metal–organic framework films enabling extreme surface wetting properties

• Andre Mähringer,
• Julian M. Rotter and
• Dana D. Medina

Beilstein J. Nanotechnol. 2019, 10, 1994–2003, doi:10.3762/bjnano.10.196

• properties and functions, MOFs are intriguing candidates for the design and synthesis of coatings combining a superhydrophilic, superhydrophobic, superoleophilic or superoleophobic character with desired features such as light filtering, hosting cavities, electrical conductivity, etc. In the literature, the

• -CAT-1 crystallites exhibit a hexagonally faceted, needle-like morphology with crystal cross-sections of 30–40 nm and several micrometers in length (Figure 1). In addition, the M-CAT-1 materials are electroactive featuring electrical conductivity values of up to 10−2–10−3 S cm−1 for pressed powder

• use of a MOF allows for encoding further desired surface properties such as light absorption and electrical conductivity. This can be valuable for applications such as photo-electrocatalysis water splitting where a high textural surface area, water contact and light absorption are required. A

Facile synthesis of carbon nanotube-supported NiO//Fe₂O₃ for all-solid-state supercapacitors

• Shengming Zhang,
• Xuhui Wang,
• Yan Li,
• Xuemei Mu,
• Yaxiong Zhang,
• Jingwei Du,
• Guo Liu,
• Xiaohui Hua,
• Yingzhuo Sheng,
• Erqing Xie and
• Zhenxing Zhang

Beilstein J. Nanotechnol. 2019, 10, 1923–1932, doi:10.3762/bjnano.10.188

• carbon cloth–carbon nanotube@metal oxide (CC-CNT@MO) three-dimensional structures combine the high specific capacitance and rich redox sites of metal oxides with the large specific area and high electrical conductivity of carbon nanotubes. The prepared CC-CNT@Fe2O3 anode reaches a high capacity of 226

• high slope at low frequency indicates small capacitive resistance (0.465 Ω) and thus fast ion transport. Therefore, the EIS results prove that the good electrochemical performance of the CC-CNT@NiO electrode can be mainly attributed to its good electrical conductivity and low charge transfer resistance

Charge-transfer interactions between fullerenes and a mesoporous tetrathiafulvalene-based metal–organic framework

• Manuel Souto,
• Joaquín Calbo,
• Samuel Mañas-Valero,
• Aron Walsh and
• Guillermo Mínguez Espallargas

Beilstein J. Nanotechnol. 2019, 10, 1883–1893, doi:10.3762/bjnano.10.183

• electron-donor TTF ligand is studied in detail by means of different spectroscopic techniques and density functional theory (DFT) calculations. Importantly, gas sorption measurements demonstrate that sorption capacity is maintained after encapsulation of fullerenes, whereas the electrical conductivity is

• catalysis [3][4][5]. In addition, electroactive MOFs combining porosity and electrical conductivity [6][7][8] have also attracted much attention during the last years in view of their potential application, for example as chemiresistive sensors [9], field-effect transistors [10] or supercapacitors [11

• ]. Whereas most MOFs are electrical insulators, some have shown to exhibit excellent electrical conductivity and high charge mobility. This was achieved either by an appropriate choice of the building units to form electronically delocalised frameworks, or by incorporating electroactive guest molecules in

TiO₂/GO-coated functional separator to suppress polysulfide migration in lithium–sulfur batteries

• Ning Liu,
• Lu Wang,
• Taizhe Tan,
• Yan Zhao and
• Yongguang Zhang

Beilstein J. Nanotechnol. 2019, 10, 1726–1736, doi:10.3762/bjnano.10.168

• effect and the Li/S batteries with these functional interlayers deliver high gravimetric energy density and superior cyclic performance. Two-dimensional graphene oxide (GO) has excellent thermal stability, an ultrahigh specific surface area, and good electrical conductivity. The polysulfide shuttle can

Tuning the performance of vanadium redox flow batteries by modifying the structural defects of the carbon felt electrode

• Ditty Dixon,
• Deepu Joseph Babu,
• Aiswarya Bhaskar,
• Hans-Michael Bruns,
• Joerg J. Schneider,
• Frieder Scheiba and
• Helmut Ehrenberg

Beilstein J. Nanotechnol. 2019, 10, 1698–1706, doi:10.3762/bjnano.10.165

• the electrical conductivity, leading to performance loss. Furthermore, it has been proposed by Schweiss et al. that an increase in the amorphous content in the felt can increase the hydrogen evolution reaction [12]. In one way or the other, functionalization with heteroatoms will always reduce the

• increase in electrical conductivity as well as active sites [16]. In this work, a carbon felt electrode with minimum oxygen functional groups and a larger amount of defects in the form of N-doping and edge sites was prepared by employing the N2 plasma technique. The N2-plasma-treated sample showed enhanced