Outstanding chain-extension effect and high UV resistance of polybutylene succinate containing amino-acid-modified layered double hydroxides

• Adam A. Marek,
• Vincent Verney,
• Christine Taviot-Gueho,
• Grazia Totaro,
• Laura Sisti,
• Annamaria Celli and
• Fabrice Leroux

Beilstein J. Nanotechnol. 2019, 10, 684–695, doi:10.3762/bjnano.10.68

• the organic anions (determined using ChemBio 3D ultra 13.0 suite software) leads us to propose a monolayer arrangement for LDH/HIS where the main plane of the molecule is oriented nearly parallel to the hydroxide layer (Figure 2). From the point of charge density, Mg2Al hydroxide layers display an

Commercial polycarbonate track-etched membranes as substrates for low-cost optical sensors

• Paula Martínez-Pérez and
• Jaime García-Rupérez

Beilstein J. Nanotechnol. 2019, 10, 677–683, doi:10.3762/bjnano.10.67

• the development of optical sensors: polycarbonate track-etched (PCTE) membranes. PCTE membranes, which are typically used for size-based filtration [9][10], are reminiscent of the porous structure of a monolayer of porous silicon, a material that has an optical response of a Fabry–Pérot (FP

Ultrathin hydrophobic films based on the metal organic framework UiO-66-COOH(Zr)

• Miguel A. Andrés,
• Clemence Sicard,
• Christian Serre,
• Olivier Roubeau and
• Ignacio Gascón

Beilstein J. Nanotechnol. 2019, 10, 654–665, doi:10.3762/bjnano.10.65

• /surfactant films containing 10 wt % octadecylphoshonic acid (ODP) have been deposited on substrates of different nature by Langmuir–Blodgett (LB) and Langmuir–Schaefer (LS) methods, showing that the presence of even only one MOF/ODP monolayer can increase the water contact angle of highly hydrophilic

• [24] and spray methods [25]. Compared to other methodologies that allow the deposition of MOF thin films, the Langmuir–Blodgett (LB) technique presents some advantages. Previous functionalization of the surface is not necessary and the film obtained can be as thin as one monolayer of MOF particles

• ODP amount contained on the monolayer MOF/ODP film. In addition, a broad feature at 5.7° is present in the MOF/ODP drop-cast sample that corresponds to pure ODP (Supporting Information File 1, Figure S7). Therefore, the crystalline structure of the MOF is preserved upon incorporation of the ODP and

Biomimetic synthesis of Ag-coated glasswing butterfly arrays as ultra-sensitive SERS substrates for efficient trace detection of pesticides

• Guochao Shi,
• Mingli Wang,
• Yanying Zhu,
• Yuhong Wang,
• Xiaoya Yan,
• Xin Sun,
• Haijun Xu and
• Wanli Ma

Beilstein J. Nanotechnol. 2019, 10, 578–588, doi:10.3762/bjnano.10.59

• layer of molecules (submonolayer to monolayer thickness) is adsorbed on the surface of the Ag-G.b.-20 substrate [33]. In the range of relatively low concentration, because all the probe molecules of CV are directly (or closely) adsorbed on the Ag-G.b.-20 substrate surface and SERS exhibits a proximity

• diameter of the illumination spot was ca. 1 µm and the penetration depth was ca. 3 mm. Hence, the value of Nbulk was ca. 1.42 × 1010. According to the above analysis, when the concentration of the CV was 10−6 M, the CV molecules were absorbed as a monolayer on the surface of the Ag-G.b.-20 substrate. The

• points. As plotted in Figure S2b, the RSD values for 915, 1172 and 1532 cm−1 were estimated to be 10.78%, 8.91% and 9.25%. Based on above results, both substrate-by-substrate and point-by-point reproducibility can be achieved with Ag-G.b.-20 substrates, which is likely connected to the monolayer

Hydrophilicity and carbon chain length effects on the gas sensing properties of chemoresistive, self-assembled monolayer carbon nanotube sensors

• Juan Casanova-Cháfer,
• Carla Bittencourt and
• Eduard Llobet

Beilstein J. Nanotechnol. 2019, 10, 565–577, doi:10.3762/bjnano.10.58

• ); self-assembled monolayer (SAM); thiol; Introduction Carbon nanotubes were first observed by Sumio Iijima in 1991 [1] and since then, this nanostructure has been widely used in chemoresistive gas sensors [2][3][4][5] due to the possibility to engineer its sensitivity towards chemicals present in a

Direct observation of the CVD growth of monolayer MoS₂ using in situ optical spectroscopy

• Claudia Beatriz López-Posadas,
• Yaxu Wei,
• Wanfu Shen,
• Daniel Kahr,
• Michael Hohage and
• Lidong Sun

Beilstein J. Nanotechnol. 2019, 10, 557–564, doi:10.3762/bjnano.10.57

• dichalcogenide (2D TMDC) materials. However, it is very challenging to carry out such studies during chemical vapor deposition (CVD). Here, we report the first, real time, in situ study of the CVD growth of 2D TMDCs. More specifically, the CVD growth of a molybdenum disulfide (MoS2) monolayer on sapphire

• substrates has been monitored in situ using differential transmittance spectroscopy (DTS). The growth of the MoS2 monolayer can be precisely followed by observation of the evolution of the characteristic optical features. Consequently, a strong correlation between the growth rate of the MoS2 monolayer and

• spectroscopy; molybdenum disulfide (MoS2) monolayer; two-dimensional transition-metal dichalcogenides (2D TMDC); Introduction Two-dimensional transition metal dichalcogenide (2D TMDC) materials have drawn wide attention because of their fascinating physical and chemical properties [1][2][3][4][5][6]. Given

Mo-doped boron nitride monolayer as a promising single-atom electrocatalyst for CO₂ conversion

• Qianyi Cui,
• Gangqiang Qin,
• Weihua Wang,
• Lixiang Sun,
• Aijun Du and
• Qiao Sun

Beilstein J. Nanotechnol. 2019, 10, 540–548, doi:10.3762/bjnano.10.55

• ), including Sc to Zn, Mo, Ru, Rh, Pd and Ag, supported on a boron nitride (BN) monolayer with boron vacancies, were investigated as electrocatalysts for the CO2 reduction reaction (CRR) using comprehensive density functional theory (DFT) calculations. The results demonstrate that a single-Mo-atom-doped boron

• nitride (Mo-doped BN) monolayer possesses excellent performance for converting CO2 to CH4 with a relatively low limiting potential of −0.45 V, which is lower than most catalysts for the selective production of CH4 as found in both theoretical and experimental studies. In addition, the formation of OCHO on

• the Mo-doped BN monolayer in the early hydrogenation steps is found to be spontaneous, which is distinct from the conventional catalysts. Mo, as a non-noble element, presents excellent catalytic performance with coordination to the BN monolayer, and is thus a promising transition metal for catalyzing

Choosing a substrate for the ion irradiation of two-dimensional materials

• Egor A. Kolesov

Beilstein J. Nanotechnol. 2019, 10, 531–539, doi:10.3762/bjnano.10.54

• irradiation of 2D materials is usually carried out on substrates [1]. However, the substrate choice is known to play a significant (and sometimes crucial) role in the irradiation process [1][2][3][4][5][6][7]. On one hand, it can increase the stability of a monolayer under irradiation, leading to reduction of

• a resultant defect yield [3]; on the other, it can participate in defect formation in the 2D material through energy transfer from sputtered substrate atoms moving through the monolayer [1][4]. When the energy is suitable, these atoms can become embedded into the 2D material crystal lattice, leading

• to a peculiar doping effect, as it was shown for graphene in [1]. Besides, one cannot exclude participation of displaced recoil atoms [8] that reach the interface but remain within the substrate. Moreover, since there is a charge transfer between the substrate and the monolayer [9][10][11][12], the

Polymorphic self-assembly of pyrazine-based tectons at the solution–solid interface

• Achintya Jana,
• Puneet Mishra and
• Neeladri Das

Beilstein J. Nanotechnol. 2019, 10, 494–499, doi:10.3762/bjnano.10.50

• topographic image of the 2,5-bis(pyridin-4-ylethynyl)pyrazine molecular monolayer at the 1-phenyloctane–HOPG interface. Molecules of 1 self-assemble to form ordered structures on a very large scale up to 500 nm × 500 nm. As clearly discernible in Figure 2a, these molecules undergo polymorphic self-assembly

Temperature-dependent Raman spectroscopy and sensor applications of PtSe₂ nanosheets synthesized by wet chemistry

• Mahendra S. Pawar and
• Dattatray J. Late

Beilstein J. Nanotechnol. 2019, 10, 467–474, doi:10.3762/bjnano.10.46

• , etc. from group IV–V and X represents the chalcogenides family, X = S, Se, Te, etc. The metal atom M is sandwiched between layers of chalcogenide (X) atoms in the structure X–M–X. The TMDCs show diverse functional properties at the monolayer level in contrast to bulk due to the quantum confinement

• semimetallic nature and single-layer PtSe2 has a semiconducting nature with a bandgap of 1.2 eV. Bilayer PtSe2 is also a semiconducting material but with a slightly smaller band gap than the monolayer material [19]. This layer-dependent conversion of semimetal-to-semiconductor transition has potential for

Removal of toxic heavy metals from river water samples using a porous silica surface modified with a new β-ketoenolic host

• Said Tighadouini,
• Smaail Radi,
• Abderrahman Elidrissi,
• Khadija Haboubi,
• Maryse Bacquet,
• Stéphanie Degoutin,
• Mustapha Zaghrioui and
• Yann Garcia

Beilstein J. Nanotechnol. 2019, 10, 262–273, doi:10.3762/bjnano.10.25

• ). This indicates that the adsorption of metal ions occurs by a monolayer formation in the same limited number of adsorption sites on a homogeneous adsorbent surface. Thermodynamic modeling. The influence of temperature on the adsorption of Zn(II), Pb(II), Cd(II) and Cu(II) ions onto SiNL was evaluated

Scanning probe microscopy for energy-related materials

• Rüdiger Berger,
• Benjamin Grévin,
• Philippe Leclère and
• Yi Zhang

Beilstein J. Nanotechnol. 2019, 10, 132–134, doi:10.3762/bjnano.10.12

• covalently grafted with a monolayer of poly(3-hexylthiophene) functionalized with carboxylic groups [8]. Their study unravels the physical mechanisms taking place locally during the photovoltaic process and its correlation to the nanoscale morphology. Electrochemical energy storage (i.e., in a battery) is a

Pull-off and friction forces of micropatterned elastomers on soft substrates: the effects of pattern length scale and stiffness

• Peter van Assenbergh,
• Marike Fokker,
• Julian Langowski,
• Jan van Esch,
• Marleen Kamperman and
• Dimitra Dodou

Beilstein J. Nanotechnol. 2019, 10, 79–94, doi:10.3762/bjnano.10.8

• this method is that it requires complex instrumentation [28]. Akerboom et al. recently demonstrated a fast and cost-effective alternative method to fabricate micropatterns, in which a colloidal monolayer acts as a three-dimensional template to shape a curable resin [29][30], resulting in arrays of sub

• without a terminal layer on friction. The fabricated sub-microscale dimples had a lower depth than the particle radius. Considering that the time between casting the monolayer with PDMS, degassing and subsequent curing at 68 °C was in the order of 15 min, the uncured PDMS does not fully flow through the

• colloidal monolayer on this timescale, resulting in a limited dimple depth. A strategy to increase the PDMS penetration into the monolayer would be to cure the PDMS at room temperature for 48 h, in which case PDMS remains in a liquid state for much longer. Indeed, we did observe larger dimples and thinner

Apparent tunneling barrier height and local work function of atomic arrays

• Neda Noei,
• Alexander Weismann and
• Richard Berndt

Beilstein J. Nanotechnol. 2018, 9, 3048–3052, doi:10.3762/bjnano.9.283

• ) terrace, a Cu adatom, a monatomic chain, a wide chain, and grooves of monolayer depth with single-atom or wider width. There are systematic differences between the slopes of the terrace data (black line) and the other data sets (colors). On asperities such as adatoms and narrow chains the current varies

• chains and trenches of monolayer height. (a) A Cu chain approximately two atoms wide and a parallel trench. (b) Two wide trenches (approx. 2 and 3 atoms) with deposited single Cu atoms. (c) Monatomic chains and trenches. The images were acquired at (a) V = 20 mV and I = 3 nA and (b, c) V = 100 mV and I

• monolayer depth with single-atom and wider width (approx. 2 atoms) are displayed. The curves are arbitrarily offset along the ordinate for clarity. The terrace data are shown with each curve for comparison. Small undulations of the data are due to low-frequency vibration of the microscope. Apparent barrier

Size limits of magnetic-domain engineering in continuous in-plane exchange-bias prototype films

• Alexander Gaul,
• Daniel Emmrich,
• Timo Ueltzhöffer,
• Henning Huckfeldt,
• Hatice Doğanay,
• Johanna Hackl,
• Muhammad Imtiaz Khan,
• Daniel M. Gottlob,
• Gregor Hartmann,
• André Beyer,
• Dennis Holzinger,
• Slavomír Nemšák,
• Claus M. Schneider,
• Armin Gölzhäuser,
• Günter Reiss and
• Arno Ehresmann

Beilstein J. Nanotechnol. 2018, 9, 2968–2979, doi:10.3762/bjnano.9.276

• were approximated from the density values of pure metals using with x being the mole fraction, x = n/100. The SRIM compound correction was deactivated for all layers except SiO2. Simulations were performed using the monolayer collision mode for 2 × 106 helium ions with a kinetic energy of 15 keV

Ternary nanocomposites of reduced graphene oxide, polyaniline and hexaniobate: hierarchical architecture and high polaron formation

• Claudio H. B. Silva,
• Maria Iliut,
• Christopher Muryn,
• Christian Berger,
• Zachary Coldrick,
• Vera R. L. Constantino,
• Marcia L. A. Temperini and
• Aravind Vijayaraghavan

Beilstein J. Nanotechnol. 2018, 9, 2936–2946, doi:10.3762/bjnano.9.272

• smooth monolayer rGO particles, which are partially restacked when deposited on the Si/SiO2 substrate. The AFM images of the rGO/PANI nanocomposite show similar flake dimensions (ca. 25 μm) as the rGO-25 sample, and no granular particles were observed, as reported for PANI aggregates [36]. On the other

Low cost tips for tip-enhanced Raman spectroscopy fabricated by two-step electrochemical etching of 125 µm diameter gold wires

• Antonino Foti,
• Francesco Barreca,
• Enza Fazio,
• Cristiano D’Andrea,
• Paolo Matteini,
• Onofrio Maria Maragò and
• Pietro Giuseppe Gucciardi

Beilstein J. Nanotechnol. 2018, 9, 2718–2729, doi:10.3762/bjnano.9.254

• bound) in gap-mode. TERS maps of sub-monolayer films of R6G on Au(111) are shown with optical resolution better than 5 nm. The procedure can in principle be applied to thinner wires to further reduce costs and production times, although issues related to the fragility of the tip and difficulties in the

Size-selected Fe₃O₄–Au hybrid nanoparticles for improved magnetism-based theranostics

• Maria V. Efremova,
• Yulia A. Nalench,
• Eirini Myrovali,
• Anastasiia S. Garanina,
• Ivan S. Grebennikov,
• Polina K. Gifer,
• Maxim A. Abakumov,
• Marina Spasova,
• Makis Angelakeris,
• Alexander G. Savchenko,
• Michael Farle,
• Natalia L. Klyachko,
• Alexander G. Majouga and
• Ulf Wiedwald

Beilstein J. Nanotechnol. 2018, 9, 2684–2699, doi:10.3762/bjnano.9.251

• positive staining of 4T1 cells is found only on the periphery of the cell monolayer. However, ROS activation is observed at this point of time – as indicated by an increased number of H2DCFDA-positive cells in the culture (Figure S5C, Supporting Information File 1). Exposure to AMF for 30 min is sufficient

Two-dimensional semiconductors pave the way towards dopant-based quantum computing

• José Carlos Abadillo-Uriel,
• Belita Koiller and
• María José Calderón

Beilstein J. Nanotechnol. 2018, 9, 2668–2673, doi:10.3762/bjnano.9.249

• instance, MoS2[32] or h-BN [33]) and the experimentally reported values lie in a wide range [32]. Typically, the dielectric constant of monolayer materials is expected to be smaller than their 3D counterparts, as their screening capabilities are reduced at low dimensionality [29][33]. All this variability

Nanoantenna structures for the detection of phonons in nanocrystals

• Alexander G. Milekhin,
• Sergei A. Kuznetsov,
• Ilya A. Milekhin,
• Larisa L. Sveshnikova,
• Tatyana A. Duda,
• Ekaterina E. Rodyakina,
• Alexander V. Latyshev,
• Volodymyr M. Dzhagan and
• Dietrich R. T. Zahn

Beilstein J. Nanotechnol. 2018, 9, 2646–2656, doi:10.3762/bjnano.9.246

• been extensively examined to date. Recently, A. Toma et al. [21] published the first report on SEIRA for detection of an optical phonon mode (so-called Froehlich mode) from a monolayer of CdSe NCs deposited on Au nanoantenna arrays. The SEIRA enhancement induced by the nanoantennas was estimated to be

• -shaped nanoantennas, were used for further SEIRA investigations. These arrays with appropriate structural parameters were also used for depositing CdSe, CdS, and PbS NCs in the Langmuir–Blodgett experiments. As it is seen from representative SEM images in Figure 7, a homogeneous monolayer of CdSe NCs is

Characterization of the microscopic tribological properties of sandfish (Scincus scincus) scales by atomic force microscopy

• Weibin Wu,
• Christian Lutz,
• Simon Mersch,
• Richard Thelen,
• Christian Greiner,
• Guillaume Gomard and
• Hendrik Hölscher

Beilstein J. Nanotechnol. 2018, 9, 2618–2627, doi:10.3762/bjnano.9.243

• . [13] sedated animals, put them on a tilted flat covered with a monolayer of granular particles, and determined the angle at which the animal started to slide in forward direction on its ventral scales. The static friction coefficient µst, determined in this more classical way, was higher for sandfish

Non-agglomerated silicon–organic nanoparticles and their nanocomplexes with oligonucleotides: synthesis and properties

• Asya S. Levina,
• Marina N. Repkova,
• Nadezhda V. Shikina,
• Zinfer R. Ismagilov,
• Svetlana A. Yashnik,
• Dmitrii V. Semenov,
• Yulia I. Savinovskaya,
• Natalia A. Mazurkova,
• Inna A. Pyshnaya and
• Valentina F. Zarytova

Beilstein J. Nanotechnol. 2018, 9, 2516–2525, doi:10.3762/bjnano.9.234

• blue) and 488 nm (for fluorescein-labeled samples, green) were used. The results are shown in Figure 5. Cell viability assays The experiments were carried out similarly as described in [20]. In short: Two days after the formation of a continuous monolayer of MDCK cells at 37 °C and 5% CO2, the cells

ZnO-nanostructure-based electrochemical sensor: Effect of nanostructure morphology on the sensing of heavy metal ions

• Marina Krasovska,
• Vjaceslavs Gerbreders,
• Irena Mihailova,
• Andrejs Ogurcovs,
• Eriks Sledevskis,
• Andrejs Gerbreders and
• Pavels Sarajevs

Beilstein J. Nanotechnol. 2018, 9, 2421–2431, doi:10.3762/bjnano.9.227

• in the substitution reaction and forms stronger bonds with the ZnO surface. The Freundlich (multilayered) adsorption model is the result of a very strong interaction [26]. By contrast, Cd–O bonds are much weaker than Pb–O bonds, so in the case of cadmium, the Langmuir (monolayer) adsorption model is

• effectiveness of sedimentation is directly related to the electronegativity of the adsorbate: substances with higher electronegativity form stronger bonds with the ZnO surface and exceed the monolayer range. This was supported by the fact that a significantly better adsorption of lead ions was observed compared

Phosphorus monolayer doping (MLD) of silicon on insulator (SOI) substrates

• Noel Kennedy,
• Ray Duffy,
• Luke Eaton,
• Dan O’Connell,
• Scott Monaghan,
• Shane Garvey,
• James Connolly,
• Chris Hatem,
• Justin D. Holmes and
• Brenda Long

Beilstein J. Nanotechnol. 2018, 9, 2106–2113, doi:10.3762/bjnano.9.199

• Applied Materials, Gloucester, Massachusetts, USA CRANN@AMBER, Trinity College Dublin, Dublin 2, Ireland 10.3762/bjnano.9.199 Abstract This paper details the application of phosphorus monolayer doping of silicon on insulator substrates. There have been no previous publications dedicated to the topic of

• and will be problematic when attempting to reach doping levels achieved by rival techniques. Keywords: CMOS; doping; monolayer; silicon; silicon on insulator (SOI); Introduction Aggressive device scaling in the sub-20 nm region has resulted in a number of techniques that were previously essential

• future device scaling that a means of damage-free, conformal doping is established, and this is where monolayer doping (MLD) appears to have potential to succeed. MLD was pioneered by Javey and co-workers [5] in 2008 and has subsequently been used to dope multiple substrate types such as silicon [5][6][7

A scanning probe microscopy study of nanostructured TiO₂/poly(3-hexylthiophene) hybrid heterojunctions for photovoltaic applications

• Laurie Letertre,
• Roland Roche,
• Olivier Douhéret,
• Hailu G. Kassa,
• Denis Mariolle,
• Nicolas Chevalier,
• Łukasz Borowik,
• Philippe Dumas,
• Benjamin Grévin,
• Roberto Lazzaroni and
• Philippe Leclère

Beilstein J. Nanotechnol. 2018, 9, 2087–2096, doi:10.3762/bjnano.9.197

• monolayer of poly(3-hexylthiophene) (P3HT) functionalized with carboxylic groups (–COOH). Through a joint analysis of the photovoltaic properties at the nanoscale by photoconductive-AFM (PC-AFM) and surface photovoltage imaging, we investigated the physical mechanisms taking place locally during the

• composed of arrays of nanoscale columns, covalently sensitized with a P3HT-COOH monolayer to form hybrid bulk heterojunctions. The grafting of P3HT on the surface of TiO2, ensured by the COOH groups, was demonstrated to be beneficial for the photoconversion efficiency of the system [16][17][18]. The