Comparing the performance of single and multifrequency Kelvin probe force microscopy techniques in air and water

• Jason I. Kilpatrick,
• Emrullah Kargin and
• Brian J. Rodriguez

Beilstein J. Nanotechnol. 2022, 13, 922–943, doi:10.3762/bjnano.13.82

• liquid environments whilst needing the smallest AC bias for operation. Keywords: AFM; atomic force microscopy; closed loop; Kelvin probe force microscope; KPFM; open loop; performance; signal-to-noise ratio; Introduction Atomic force microscopy (AFM) is an enabling technique for the nanoscale mapping

Temperature and chemical effects on the interfacial energy between a Ga–In–Sn eutectic liquid alloy and nanoscopic asperities

• Yujin Han,
• Pierre-Marie Thebault,
• Corentin Audes,
• Xuelin Wang,
• Haiwoong Park,
• Jian-Zhong Jiang and
• Arnaud Caron

Beilstein J. Nanotechnol. 2022, 13, 817–827, doi:10.3762/bjnano.13.72

• increase of the interfacial energy as a function of the temperature, which can be explained by the reactivity between SiOx and Ga and the occurrence of chemical segregation at the liquid alloy surface. Keywords: atomic force microscopy (AFM); interfacial energy; liquid alloy; Introduction Recently, room

• atomic force microscopy (AFM) tips of different chemistries as a function of the temperature (T = 21–90 °C) by AFM force spectroscopy using an XE100 AFM equipped with a heating stage (manufactured by Park Instruments, Republic of Korea). We recorded force–distance curves with PtSi-coated Si cantilevers

Efficient liquid exfoliation of KP₁₅ nanowires aided by Hansen's empirical theory

• Zhaoxuan Huang,
• Zhikang Jiang,
• Nan Tian,
• Disheng Yao,
• Fei Long,
• Yanhan Yang and
• Danmin Liu

Beilstein J. Nanotechnol. 2022, 13, 788–795, doi:10.3762/bjnano.13.69

• concentration, centrifugation was not used. Measurement equipment UV−visible spectrophotometry was performed by using a Shimadzu UV-3101PC system. Atomic force microscopy (AFM) tests were performed in a Multimode 8 system. The Raman tests were performed on a WITec alpha300 RA confocal Raman microscopy system

Direct measurement of surface photovoltage by AC bias Kelvin probe force microscopy

• Masato Miyazaki,
• Yasuhiro Sugawara and
• Yan Jun Li

Beilstein J. Nanotechnol. 2022, 13, 712–720, doi:10.3762/bjnano.13.63

• features as band bending [3][4], the lifetimes of excited carriers [5][6][7], the minority carrier diffusion length [8][9], and the plasmonic effect [10][11][12]. The local SPV is usually measured by Kelvin probe force microscopy (KPFM) [13][14][15][16][17][18][19][20][21], which is based on atomic force

• microscopy (AFM) [22]. KPFM measures the contact potential difference (CPD), which corresponds to the difference in work function between the tip and the sample, consecutively in darkness and under illumination, to determine the SPV values: SPV = CPDlight − CPDdark. In this method, the thermal drift between

Reliable fabrication of transparent conducting films by cascade centrifugation and Langmuir–Blodgett deposition of electrochemically exfoliated graphene

• Teodora Vićentić,
• Stevan Andrić,
• Vladimir Rajić and
• Marko Spasenović

Beilstein J. Nanotechnol. 2022, 13, 666–674, doi:10.3762/bjnano.13.58

• wavelength of 660 nm and the number of graphene layers was calculated for each sample, taking into account an absorption of 2.3% for each layer of graphene, as in the work by Bonaccorso and co-workers [43]. Although atomic force microscopy (AFM) is often employed to characterize graphene films [2][12][14][44

Quantitative dynamic force microscopy with inclined tip oscillation

• Philipp Rahe,
• Daniel Heile,
• Reinhard Olbrich and
• Michael Reichling

Beilstein J. Nanotechnol. 2022, 13, 610–619, doi:10.3762/bjnano.13.53

• Philipp Rahe Daniel Heile Reinhard Olbrich Michael Reichling Fachbereich Physik, Universität Osnabrück, Barbarastrasse 7, 49076 Osnabrück, Germany 10.3762/bjnano.13.53 Abstract In the mathematical description of dynamic atomic force microscopy (AFM), the relation between the tip–surface normal

• Atomic force microscopy (AFM) is a quantitative technique that allows for probing the force field above a surface in one, two, or three dimensions. While imaging in a plane parallel to the surface provides nanoscale and atomic structural information [1], force curves, usually acquired along a recording

Revealing local structural properties of an atomically thin MoSe₂ surface using optical microscopy

• Lin Pan,
• Peng Miao,
• Anke Horneber,
• Alfred J. Meixner,
• Pierre-Michel Adam and
• Dai Zhang

Beilstein J. Nanotechnol. 2022, 13, 572–581, doi:10.3762/bjnano.13.49

• the optical contrast, one can estimate that the thickness of the more transparent areas of the MoSe2 flake is smaller than that of other regions. To visualize the CuPc molecule distribution on the MoSe2 flake, atomic force microscopy (AFM) was used, and the results are shown in Figure 1b. The insets

Effects of substrate stiffness on the viscoelasticity and migration of prostate cancer cells examined by atomic force microscopy

• Xiaoqiong Tang,
• Yan Zhang,
• Jiangbing Mao,
• Yuhua Wang,
• Zhenghong Zhang,
• Zhengchao Wang and
• Hongqin Yang

Beilstein J. Nanotechnol. 2022, 13, 560–569, doi:10.3762/bjnano.13.47

• unclear how mechanical properties regulate the cellular response to the environmental matrix. In this study, atomic force microscopy (AFM) and laser confocal imaging were used to qualitatively evaluate the relationship between substrate stiffness and migration of prostate cancer (PCa) cells. Cells

• functions have not been well appreciated [16]. In recent years, alterations in the physical properties of cells have been considered as a marker of malignant transformation of cancer cells [17][18][19]. Based on atomic force microscopy (AFM) measurements, our group found that the progression of prostate

Relationship between corrosion and nanoscale friction on a metallic glass

• Haoran Ma and
• Roland Bennewitz

Beilstein J. Nanotechnol. 2022, 13, 236–244, doi:10.3762/bjnano.13.18

• surface dissolution at the interface of the two layers. The findings contribute to the understanding of mechanical contacts with metallic glasses under corrosive conditions by exploring the interrelation of microscopic corrosion mechanisms and nanoscale friction. Keywords: atomic force microscopy (AFM

Topographic signatures and manipulations of Fe atoms, CO molecules and NaCl islands on superconducting Pb(111)

• Carl Drechsel,
• Philipp D’Astolfo,
• Jung-Ching Liu,
• Thilo Glatzel,
• Rémy Pawlak and
• Ernst Meyer

Beilstein J. Nanotechnol. 2022, 13, 1–9, doi:10.3762/bjnano.13.1

• microscopy (STM) and atomic force microscopy (AFM) are required to accurately disentangle structural and electronic properties of atomic or molecular structures on these superconducting platforms. STM/AFM generally allows for a controlled repositioning of adsorbates, both by lateral and vertical

Measurement of polarization effects in dual-phase ceria-based oxygen permeation membranes using Kelvin probe force microscopy

• Kerstin Neuhaus,
• Christina Schmidt,
• Liudmila Fischer,
• Wilhelm Albert Meulenberg,
• Ke Ran,
• Joachim Mayer and
• Stefan Baumann

Beilstein J. Nanotechnol. 2021, 12, 1380–1391, doi:10.3762/bjnano.12.102

• |ceria, ceria|electron conductor, and electron conductor|electron conductor). Kelvin probe force microscopy (KPFM) is an atomic force microscopy (AFM)-based measurement method that can measure the local surface potential (or Volta potential) of the sample [18][19]. The surface potential is a sensitive

Alteration of nanomechanical properties of pancreatic cancer cells through anticancer drug treatment revealed by atomic force microscopy

• Xiaoteng Liang,
• Shuai Liu,
• Xiuchao Wang,
• Dan Xia and
• Qiang Li

Beilstein J. Nanotechnol. 2021, 12, 1372–1379, doi:10.3762/bjnano.12.101

• from measuring the alteration of cellular mechanics, which provides a guide for the innovation and development of anticancer drugs [11]. Atomic force microscopy (AFM) has matured into a forceful nanoscale platform for imaging biological samples and quantifying biomechanical properties of living cells

Cantilever signature of tip detachment during contact resonance AFM

• Devin Kalafut,
• Ryan Wagner,
• Maria Jose Cadena,
• Anil Bajaj and
• Arvind Raman

Beilstein J. Nanotechnol. 2021, 12, 1286–1296, doi:10.3762/bjnano.12.96

• connect the qualitative and quantitative behavior to experimental features. Keywords: atomic force microscopy (AFM); contact resonance; nonlinear normal mode (NNM); tip–sample detachment; photothermal excitation; Introduction Contact resonance atomic force microscopy (CR-AFM) [1][2], piezoresponse force

• microscopy (PFM) [3], and electrochemical strain microscopy (ESM) [4] are atomic force microscopy (AFM) [5] methods where the probe tip is held in contact with the sample at a constant average force while a small superimposed vibrational response is monitored. CR-AFM can measure the viscoelastic properties

A review on slip boundary conditions at the nanoscale: recent development and applications

• Ruifei Wang,
• Jin Chai,
• Bobo Luo,
• Xiong Liu,
• Jianting Zhang,
• Min Wu,
• Mingdan Wei and
• Zhuanyue Ma

Beilstein J. Nanotechnol. 2021, 12, 1237–1251, doi:10.3762/bjnano.12.91

• nanoscale systems [8][34][38][39]. For example, based on surface force apparatus (SFA) and atomic force microscopy (AFM) measurements, many researchers have investigated the slippage characteristics of nanoconfined liquid flows and derived the slip length according to its correlation with the hydrodynamic

Two dynamic modes to streamline challenging atomic force microscopy measurements

• Alexei G. Temiryazev,
• Andrey V. Krayev and
• Marina P. Temiryazeva

Beilstein J. Nanotechnol. 2021, 12, 1226–1236, doi:10.3762/bjnano.12.90

• ; Introduction More than 30 years have passed since the introduction of atomic force microscopy (AFM) [1]. This technique has established itself as an indispensable tool for characterization not only in physics and chemistry, but also in related fields of research including medicine, biology, and materials

Open-loop amplitude-modulation Kelvin probe force microscopy operated in single-pass PeakForce tapping mode

• Gheorghe Stan and
• Pradeep Namboodiri

Beilstein J. Nanotechnol. 2021, 12, 1115–1126, doi:10.3762/bjnano.12.83

• (OL) variant of Kelvin probe force microscopy (KPFM) provides access to the voltage response of the electrostatic interaction between a conductive atomic force microscopy (AFM) probe and the investigated sample. The measured response can be analyzed a posteriori, modeled, and interpreted to include

A new method for obtaining model-free viscoelastic material properties from atomic force microscopy experiments using discrete integral transform techniques

• Berkin Uluutku,
• Enrique A. López-Guerra and
• Santiago D. Solares

Beilstein J. Nanotechnol. 2021, 12, 1063–1077, doi:10.3762/bjnano.12.79

• at the micro- and the nanoscale is commonly performed with the aid of force–distance relationships acquired using atomic force microscopy (AFM). The general strategy for existing methods is to fit the observed material behavior to specific viscoelastic models, such as generalized viscoelastic models

• ; Introduction Atomic force microscopy (AFM) is a prominent technique for investigating material properties at the micro- and the nanoscale [1][2][3], within which a wide variety of instruments, probes, and analysis techniques have been developed to attempt meaningful material property extraction [4][5][6][7][8

Revealing the formation mechanism and band gap tuning of Sb₂S₃ nanoparticles

• Maximilian Joschko,
• Franck Yvan Fotue Wafo,
• Christina Malsi,
• Danilo Kisić,
• Ivana Validžić and
• Christina Graf

Beilstein J. Nanotechnol. 2021, 12, 1021–1033, doi:10.3762/bjnano.12.76

• . Atomic force microscopy (AFM) as an additional method of size determination was applied to confirm the TEM results of the sample obtained after 30 s reaction time. AFM enables imaging of the nanoparticles under milder conditions than TEM and at ambient conditions so that thermal damage of the

Molecular assemblies on surfaces: towards physical and electronic decoupling of organic molecules

• Sabine Maier and
• Meike Stöhr

Beilstein J. Nanotechnol. 2021, 12, 950–956, doi:10.3762/bjnano.12.71

• . To a lesser extent, metal oxides have also been used, for which defects and charging often pose additional challenges [44][45][46]. On electronically insulating surfaces, non-contact atomic force microscopy (AFM) is the method of choice to study molecular assemblies and individual molecules in real

Self-assembly of Eucalyptus gunnii wax tubules and pure ß-diketone on HOPG and glass

• Miriam Anna Huth,
• Axel Huth and
• Kerstin Koch

Beilstein J. Nanotechnol. 2021, 12, 939–949, doi:10.3762/bjnano.12.70

• is unknown. In this study, extracted wax of E. gunnii leaves and pure ß-diketone were recrystallized on two different artificial materials and analyzed by scanning electron microscopy (SEM) and atomic force microscopy (AFM) to study their formation process. Both the wax mixture and pure ß-diketone

• formation of the tubules [26]. Atomic force microscopy (AFM) investigations further showed that the elongation of secondary alcohol tubules is based on a helical growth mechanism [27]. Recrystallization experiments with nonacosan-10-ol on non-biological substrates showed that the chemical and physical

The role of convolutional neural networks in scanning probe microscopy: a review

• Ido Azuri,
• Irit Rosenhek-Goldian,
• Neta Regev-Rudzki,
• Georg Fantner and
• Sidney R. Cohen

Beilstein J. Nanotechnol. 2021, 12, 878–901, doi:10.3762/bjnano.12.66

• , convolutional neural networks, and how it is transforming the acquisition and analysis of scanning probe data. Keywords: atomic force microscopy (AFM); deep learning; machine learning; neural networks; scanning probe microscopy (SPM); Review Introduction: traditional machine learning vs deep learning Machine

Reducing molecular simulation time for AFM images based on super-resolution methods

• Zhipeng Dou,
• Jianqiang Qian,
• Yingzi Li,
• Rui Lin,
• Jianhai Wang,
• Peng Cheng and
• Zeyu Xu

Beilstein J. Nanotechnol. 2021, 12, 775–785, doi:10.3762/bjnano.12.61

• Zhipeng Dou Jianqiang Qian Yingzi Li Rui Lin Jianhai Wang Peng Cheng Zeyu Xu School of Physics, Beihang University, Beijing 100083, China 10.3762/bjnano.12.61 Abstract Atomic force microscopy (AFM) has been an important tool for nanoscale imaging and characterization with atomic and subatomic

9.1% efficient zinc oxide/silicon solar cells on a 50 μm thick Si absorber

• Rafal Pietruszka,
• Bartlomiej S. Witkowski,
• Monika Ozga,
• Katarzyna Gwozdz,
• Ewa Placzek-Popko and
• Marek Godlewski

Beilstein J. Nanotechnol. 2021, 12, 766–774, doi:10.3762/bjnano.12.60

• the tested PV cells, as measured with atomic force microscopy (AFM). The results for the photovoltaic cell modified with zinc oxide nanorods are shown in Figure 4a and Figure 4c. The results for the planar cell are shown in Figure 4b and Figure 4d. There are significant differences in the roughness

Physical constraints lead to parallel evolution of micro- and nanostructures of animal adhesive pads: a review

• Thies H. Büscher and
• Stanislav N. Gorb

Beilstein J. Nanotechnol. 2021, 12, 725–743, doi:10.3762/bjnano.12.57

• CC BY 4.0). (D–G) Atomic force microscopy (AFM) height images of the footprint droplets of the beetle Coccinella septempunctata (D,F) and the fly Calliphora vicina (E,G). (D) and (E) share the same colour scale. Brighter pixels correspond to higher z values. (F,G) Three-dimensional impressions of the

A review of defect engineering, ion implantation, and nanofabrication using the helium ion microscope

• Frances I. Allen

Beilstein J. Nanotechnol. 2021, 12, 633–664, doi:10.3762/bjnano.12.52