Extended iron phthalocyanine islands self-assembled on a Ge(001):H surface

• Rafal Zuzak,
• Marek Szymonski and
• Szymon Godlewski

Beilstein J. Nanotechnol. 2021, 12, 232–241, doi:10.3762/bjnano.12.19

• bond dimer (DBD) is formed. A typical STM appearance of the Ge(001):H surface with the above atomic-scale defects is shown in Figure 1. Molecular islands of FePc on Ge(001):H After deposition of FePc molecules onto a Ge(001):H surface at room temperature, we observe single molecules distributed over

• or the ligands are recorded [24]. The above findings indicate that the FePc molecules stay intact upon deposition on the Ge(001):H surface and that they are decoupled from the germanium substrate by the passivating hydrogen layer. Moreover, the manipulation event allows for the identification of the

• crystals, n-type, 45 Ω·cm). After insertion into the UHV system the samples were sputtered and annealed for 15 min (Ar+, 600 eV, 1020 K). The Ge sample was hydrogenated using a custom-built hydrogen cracker following the procedure described in [61]. Deposition of the FePc molecules (Sigma-Aldrich, purity

TiO_x/Pt₃Ti(111) surface-directed formation of electronically responsive supramolecular assemblies of tungsten oxide clusters

• Marco Moors,
• Yun An,
• Agnieszka Kuc and
• Kirill Yu. Monakhov

Beilstein J. Nanotechnol. 2021, 12, 203–212, doi:10.3762/bjnano.12.16

• . However, the resulting formation of W3O9 by thermal WO3 evaporation under UHV conditions differs significantly from other WO3 deposition techniques. For example, the formation of hydrated tungsten acid species could be demonstrated by electrochemical evaporation of tungsten oxide on rutile surfaces under

• with a constant distance between them. The DFT calculations of a very similar oxide phase, grown by a reactive Ti deposition on Pt(111) [25], showed that the brightest spots belong to fourfold oxygen-coordinated titanium atoms, whereas threefold coordinated Ti atoms are depicted with less contrast. The

• control in ultrathin film growth is usually challenging by classical deposition methods. Conclusion We showcased the ordered growth of W3O9 nanoclusters on different ultrathin films of titanium oxide formed by a controlled oxidation of the bimetallic Pt3Ti(111) alloy surface. Depending on the

Imaging of SARS-CoV-2 infected Vero E6 cells by helium ion microscopy

• Natalie Frese,
• Patrick Schmerer,
• Martin Wortmann,
• Matthias Schürmann,
• Matthias König,
• Michael Westphal,
• Friedemann Weber,
• Holger Sudhoff and
• Armin Gölzhäuser

Beilstein J. Nanotechnol. 2021, 12, 172–179, doi:10.3762/bjnano.12.13

• virus particles lying on top of the membrane. After prolonged imaging, it was found that ion-induced deposition of hydrocarbons from the vacuum renders the sample sufficiently conductive to allow for imaging even without charge compensation. The presented images demonstrate the potential of the HIM in

• addition to the improved conductivity of the specimen, the deposited layer may contribute to the electron density of the surface, thus increasing secondary electron yield. This effect, commonly referred to as electron- and/or ion beam-induced deposition, is commonly observed in charged-particle microscopes

• . In electron microscopes, deposition rates of up to 3 Å/s at high current densities have been reported. As the deposition rate quickly reaches an equilibrium with rising current density, it can be assumed that the limiting factor is the density of residual hydrocarbons in the vacuum [31]. In the HIM

Paper-based triboelectric nanogenerators and their applications: a review

• Jing Han,
• Nuo Xu,
• Yuchen Liang,
• Mei Ding,
• Junyi Zhai,
• Qijun Sun and
• Zhong Lin Wang

Beilstein J. Nanotechnol. 2021, 12, 151–171, doi:10.3762/bjnano.12.12

• . Therefore, corresponding treatment processes (e.g., deposition of conductive materials by laser patterning, screen printing, spray coating, thermal deposition, surface morphology engineering, and chemical modification [46][92][93][94][95][96][97][98]) are often applied to convert paper into a conductive

• process or to rotary screen printing, which enables a facile and high-throughput printing on curved surfaces. The deposition process assisted with soft stencils is another “bottom-up” method for the preparation of functional materials on flexible and irregular surfaces. Even though P-TENGs require

• stencils by thermal/e-beam evaporation, sputter deposition, or spray deposition. When the stencils are peeled off they can readily leave the metallic patterns on the paper substrate [102] (Figure 5a). In comparison to the conventional printing techniques, vacuum evaporation and vacuum deposition techniques

A review on the green and sustainable synthesis of silver nanoparticles and one-dimensional silver nanostructures

• Sina Kaabipour and
• Shohreh Hemmati

Beilstein J. Nanotechnol. 2021, 12, 102–136, doi:10.3762/bjnano.12.9

• processes [143][144][145][146], conventional chemical reduction [147][148][149][150][151], reverse micelle [152][153][154], co-precipitation [155], chemical vapor deposition [156][157][158], solvothermal [159][160][161], and electrochemical reduction [162][163][164][165]. Chemical synthesis methods are

• deposition process. Chemical vapor deposition (CVD) and atomic layer deposition (ALD) are among other chemical methods for nanoparticle synthesis. CVD is a method that allows production of nanoparticles on a substrate [241]. The process consists of three steps. First, the addition of a volatile precursor in

• AgNPs include the precursor introduction method, reactor pressure, gas flow properties, deposition rate, deposition duration, and substrate surface temperature [157][241]. The type of precursor appears to be the most significant factor in the process [241]. Silver nitrate is the most widely used

Fusion of purple membranes triggered by immobilization on carbon nanomembranes

• René Riedel,
• Natalie Frese,
• Fang Yang,
• Martin Wortmann,
• Raphael Dalpke,
• Daniel Rhinow,
• Norbert Hampp and
• Armin Gölzhäuser

Beilstein J. Nanotechnol. 2021, 12, 93–101, doi:10.3762/bjnano.12.8

• reflection absorption spectroscopy (IRRAS). Experimental Preparation of SAMs and CNMs NBPT was purchased from Taros Chemicals (Dortmund, Germany). Thermally evaporated Au films (300 nm) on mica supports (Georg Albert physical vapor deposition coatings) were used as substrates for the SAM preparation

• using OriginPro 8 SR0 v8.0724 (OriginLab Corporation, Wellesley Hills, MA, USA). Results and Discussion Improving substrate coverage and PM orientation An oriented deposition of the PM patches is required to take advantage of the unidirectional proton transferability of PM. Preliminary experiments were

• synthesis route is well established and the resulting CNM has reactive amino head groups that can be functionalized in subsequent experiments. The functionalization of the CNM is necessary to immobilize the PM patches by chemical complex formation after deposition. In a first step, simple drop-casting

The role of gold atom concentration in the formation of Cu–Au nanoparticles from the gas phase

• Yuri Ya. Gafner,
• Svetlana L. Gafner,
• Darya A. Ryzkova and
• Andrey V. Nomoev

Beilstein J. Nanotechnol. 2021, 12, 72–81, doi:10.3762/bjnano.12.6

• –Au clusters are formed with chemical compositions corresponding to the composition of the evaporated material [14]. In the case of cluster deposition onto amorphous carbon, various cluster morphologies were observed, such as cuboctahedral and decahedral. For clusters supported on a MgO substrate

• and internal structure, and the main mechanisms involved in the formation of binary Cu–Au nanoparticles upon deposition from a gaseous medium. Computer Model Synthesis from the gas phase is one of the main physical methods used for producing nanopowders. However, since particle formation reactions

• simulation and the data on the size distribution of Cu3Au clusters obtained by laser deposition [3]. An analysis of the shape and distribution of the Cu3Au clusters on the substrate indicates that the agglomeration processes were suppressed in this case [3]. The reason for that may be the wide spatial

Atomic layer deposited films of Al₂O₃ on fluorine-doped tin oxide electrodes: stability and barrier properties

• Hana Krýsová,
• Michael Neumann-Spallart,
• Hana Tarábková,
• Pavel Janda,
• Ladislav Kavan and
• Josef Krýsa

Beilstein J. Nanotechnol. 2021, 12, 24–34, doi:10.3762/bjnano.12.2

• , Technická 5, 166 28 Prague 6, Czech Republic 10.3762/bjnano.12.2 Abstract Al2O3 layers were deposited onto electrodes by atomic layer deposition. Solubility and electron-transport blocking were tested. Films deposited onto fluorine-doped tin oxide (FTO, F:SnO2/glass) substrates blocked electron transfer to

• found up to 24 h and even after 168 h of exposure the changes in the blocking behaviour were still minimal. This behaviour was also observed for protection against direct reduction of FTO. Keywords: Al2O3; atomic layer deposition (ALD); barrier properties; corrosion; electrochemistry; FTO

• the topic of the present work, in which atomic layer deposition (ALD) is used as the coating technique [1]. This method is a gas-phase process which relies on a molecular approach. Therefore, a conformal coating, which reaches the pores and crevasses of the sample, can be obtained. Protective coating

Bio-imaging with the helium-ion microscope: A review

• Matthias Schmidt,
• James M. Byrne and
• Ilari J. Maasilta

Beilstein J. Nanotechnol. 2021, 12, 1–23, doi:10.3762/bjnano.12.1

Towards 3D self-assembled rolled multiwall carbon nanotube structures by spontaneous peel off

• Jonathan Quinson

Beilstein J. Nanotechnol. 2020, 11, 1865–1872, doi:10.3762/bjnano.11.168

• nanotube forests. The multiwall carbon nanotube structures are comprised of nitrogen-doped and undoped sections, and are obtained via a detailed peel off and roll mechanism. These results open new doors for the development of increasingly complex nanostructures. Keywords: chemical vapor deposition

• change within CNTs and to optimize the formation of complex CNT structures, the possibility to couple aerosol-assisted chemical vapor deposition (AACVD) [20] and chemical vapor deposition (CVD) was explored [16]. For detailed synthesis and characterization protocols, including control experiments, please

Piezotronic effect in AlGaN/AlN/GaN heterojunction nanowires used as a flexible strain sensor

• Jianqi Dong,
• Liang Chen,
• Yuqing Yang and
• Xingfu Wang

Beilstein J. Nanotechnol. 2020, 11, 1847–1853, doi:10.3762/bjnano.11.166

• structures used in this study were synthesized by metal-organic chemical vapor deposition (MOCVD), as shown in Figure 1a. First, 1 μm of an unintentionally doped GaN layer was deposited onto a sapphire substrate. Then, 500 nm of n-type GaN, as a current-spreading layer, was deposited to increase the lateral

Unravelling the interfacial interaction in mesoporous SiO₂@nickel phyllosilicate/TiO₂ core–shell nanostructures for photocatalytic activity

• Bridget K. Mutuma,
• Xiluva Mathebula,
• Isaac Nongwe,
• Bonakele P. Mtolo,
• Boitumelo J. Matsoso,
• Rudolph Erasmus,
• Zikhona Tetana and
• Neil J. Coville

Beilstein J. Nanotechnol. 2020, 11, 1834–1846, doi:10.3762/bjnano.11.165

• phyllosilicate can be obtained either by a hydrothermal method or a deposition-precipitation method, the 2:1 nickel phyllosilicate is only formed under hydrothermal conditions [32][33][34]. Recently, several researchers have reported on the generation of nickel phyllosilicate catalysts for hydrogenation

• . Therefore, in this study we report on the growth of mesoporous SiO2@NiPS and titania-coated mSiO2@NiPS (mSiO2@NiPS/TiO2) core–shell nanostructures using a simple deposition-precipitation method. Transmission electron microscopy (TEM), N2 physisorption analysis, diffuse reflectance UV–visible spectroscopy

• NiPS nickel phyllosilicate structure Si2Ni3O5(OH)4 [42][43]. Basically, NiPS is formed upon the precipitation of nickel species onto a silica surface after basification of a nickel(II) solution [44]. Depending on the deposition-precipitation time, the molar ratio between urea and nickel precursor, and

Nanomechanics of few-layer materials: do individual layers slide upon folding?

• Ronaldo J. C. Batista,
• Rafael F. Dias,
• Ana P. M. Barboza,
• Alan B. de Oliveira,
• Taise M. Manhabosco,
• Thiago R. Gomes-Silva,
• Matheus J. S. Matos,
• Andreij C. Gadelha,
• Cassiano Rabelo,
• Luiz G. L. Cançado,
• Ado Jorio,
• Hélio Chacham and
• Bernardo R. A. Neves

Beilstein J. Nanotechnol. 2020, 11, 1801–1808, doi:10.3762/bjnano.11.162

• exfoliated onto a silicon oxide substrate (blue shades). During the exfoliation/deposition processes, such a talc flake folds over itself, creating a well-defined folded edge, shown in orange shades. Figure 1b shows a schematic drawing of the morphology of the fold in Figure 1a. This is the morphology of the

Electron beam-induced deposition of platinum from Pt(CO)₂Cl₂ and Pt(CO)₂Br₂

• Aya Mahgoub,
• Hang Lu,
• Rachel M. Thorman,
• Konstantin Preradovic,
• Titel Jurca,
• Lisa McElwee-White,
• Howard Fairbrother and
• Cornelis W. Hagen

Beilstein J. Nanotechnol. 2020, 11, 1789–1800, doi:10.3762/bjnano.11.161

• platinum precursors, Pt(CO)2Cl2 and Pt(CO)2Br2, were designed for focused electron beam-induced deposition (FEBID) with the aim of producing platinum deposits of higher purity than those deposited from commercially available precursors. In this work, we present the first deposition experiments in a

• deposits contained halogen species and little or no carbon, while the SEM deposits contained only small amounts of halogen species but high carbon content. Results from this study highlight the effect that deposition conditions can have on the composition of deposits created by FEBID. Keywords: energy

• -dispersive X-ray spectroscopy (EDX); focused electron beam-induced deposition (FEBID); nanofabrication; platinum precursors; scanning electron microscopy (SEM); thermogravimetric analysis (TGA); Introduction Focused electron beam-induced deposition (FEBID) is a direct-write nanopatterning technique. FEBID

Molecular dynamics modeling of the influence forming process parameters on the structure and morphology of a superconducting spin valve

• Alexander Vakhrushev,
• Aleksey Fedotov,
• Vladimir Boian,
• Roman Morari and
• Anatolie Sidorenko

Beilstein J. Nanotechnol. 2020, 11, 1776–1788, doi:10.3762/bjnano.11.160

• molecular dynamics method using the many-particle potential of the modified embedded-atom method. In the calculation process the temperature was controlled using the Nose–Hoover thermostat. The simulation of the atomic nanolayer formation was performed by alternating the directional deposition of different

• atomic structures depending on the main parameters of the deposition process. Keywords: hybrid nanostructure; mathematical modeling; modified embedded-atom method; molecular dynamics; spintronics; spin valve; vacuum deposition; Introduction Multilayer superconductor/ferromagnetic (S/F) hybrid

• films. For highly mutually soluble metals, such as vanadium and iron (solubility of about 30% at room temperature), the quantum-mechanical transparency parameter is many times higher, TF ≈ 1.6. However, if the structural quality of the films requires deposition on a substrate heated to 100–300 °C, there

Mapping of integrated PIN diodes with a 3D architecture by scanning microwave impedance microscopy and dynamic spectroscopy

• Rosine Coq Germanicus,
• Peter De Wolf,
• Florent Lallemand,
• Catherine Bunel,
• Serge Bardy,
• Hugues Murray and
• Ulrike Lüders

Beilstein J. Nanotechnol. 2020, 11, 1764–1775, doi:10.3762/bjnano.11.159

• lightly doped n-type epitaxial silicon layer is, then, grown on top of the buried layer using chemical vapour deposition. The targeted epitaxial layer thickness is 7.5 µm with a resistivity of 12 Ω·cm. The anode of the diode is formed by a 30 µm diameter p+ layer, also made by the implantation and

• polysilicon layer, both deposited by low-pressure chemical vapour deposition (LPCVD). Figure 6 shows the mappings obtained on the cross section of the bottom of a deep trench, showing the ∂C/∂V phase, ∂C/∂V amplitude, sMIM-R, and sMIM-C responses. The signature of the ∂C/∂V phase (Figure 6a) clearly reveals

PEG/PEI-functionalized single-walled carbon nanotubes as delivery carriers for doxorubicin: synthesis, characterization, and in vitro evaluation

• Shuoye Yang,
• Zhenwei Wang,
• Yahong Ping,
• Yuying Miao,
• Yongmei Xiao,
• Lingbo Qu,
• Lu Zhang,
• Yuansen Hu and
• Jinshui Wang

Beilstein J. Nanotechnol. 2020, 11, 1728–1741, doi:10.3762/bjnano.11.155

• diffraction patterns of the CNTs remain the same after conjugation with PEG and PEI, which indicate that the surface modification will not change the atomic structure of CNTs. The morphology of the different nanocarriers was observed using AFM after deposition on a mica substrate. The raw SWCNTs exhibit large

Functional nanostructures for electronics, spintronics and sensors

• Anatolie S. Sidorenko

Beilstein J. Nanotechnol. 2020, 11, 1704–1706, doi:10.3762/bjnano.11.152

• technology including lift-off electron-beam lithography followed by ultra-high-vacuum deposition of materials that was used for fabrication of nanostructured quasi-1D chains of Josephson junctions. This was followed by the work of Mohammed et al. [12] who presented a smart vacuum technology for the design of

Out-of-plane surface patterning by subsurface processing of polymer substrates with focused ion beams

• Serguei Chiriaev,
• Luciana Tavares,
• Vadzim Adashkevich,
• Arkadiusz J. Goszczak and
• Horst-Günter Rubahn

Beilstein J. Nanotechnol. 2020, 11, 1693–1703, doi:10.3762/bjnano.11.151

• -assisted chemical etching and ion-beam-assisted chemical vapor deposition [1][2][3]. All these methods are based on processes that either add or remove atoms on the surface or in the subsurface atomic layers. The ion beams deposit their energy and, therefore, affect the structure and properties of

• strain accumulation followed by the relaxation of this strain at a certain critical value. Experimental Materials and samples The PMMA and PDMS substrates used in this study were deposited onto the surface of blank silicon wafers. The deposition of PMMA was performed by spin coating in an RRT Lanz EBS 11

• spin coater, in the same manner described in [4]. After the deposition, the samples were annealed at 200 °C for 90 s to remove solvent residuals. The PDMS polymer used was a two-component Dow Sylgard™184 silicone elastomer with a hardness value of 43 in the Durometer Shore scale. After mixing the

The influence of an interfacial hBN layer on the fluorescence of an organic molecule

• Christine Brülke,
• Oliver Bauer and
• Moritz M. Sokolowski

Beilstein J. Nanotechnol. 2020, 11, 1663–1684, doi:10.3762/bjnano.11.149

• directly on metal substrates by chemical vapor deposition [2]. This is, for example, exploited when a 2DM interfacial layer is inserted between the metallic electrode and a functional organic layer of an organic electronic device, such as an organic light emitting diode [3]. The purpose of the interfacial

• ) surface, the hBN layers, and the PTCDA layers was checked by LEED. We used a SPA-LEED instrument as described in [30]. An additional annealing step between the last sputter cycle and the borazine deposition was omitted here in order to prevent segregation of chemical impurities from the Cu bulk to the

• minute. During deposition, the sample was held at a constant temperature. PTCDA layers on Cu(111) were prepared by keeping the sample at a temperature of either 20 or 300 K during deposition. PTCDA layers on hBN/Cu(111) were prepared by deposition at a sample temperature of 20 K and subsequent annealing

Amorphized length and variability in phase-change memory line cells

• Nafisa Noor,
• Sadid Muneer,
• Raihan Sayeed Khan,
• Anna Gorbenko and
• Helena Silva

Beilstein J. Nanotechnol. 2020, 11, 1644–1654, doi:10.3762/bjnano.11.147

• voltage depends on the device geometry [17]. As-deposited amorphous cells of known dimensions were used in the measurements, instead of melt-quenched cells, to avoid the difficulty in determining the dimensions of the amorphized regions. However, the drift time since deposition, which is a critical

PTCDA adsorption on CaF₂ thin films

• Philipp Rahe

Beilstein J. Nanotechnol. 2020, 11, 1615–1622, doi:10.3762/bjnano.11.144

• (111) surface with deposition on thicker CaF2/CaF1/Si(111) films. The identification of mostly single molecules on the CaF1/Si(111) interface layer is explained by the presence of atomic-size defects within this layer. Geometry-optimisation calculations using density functional theory reveal a geometry

• of 3,4,9,10-perylene tetracarboxylic dianhydride (PTCDA) on metal [6][7][8][9][10][11][12], semiconductor [13], and insulator surfaces [14][15][16][17][18][19], as well as the deposition on conducting surfaces covered by insulating thin films [20][21][22][23][24] or two-dimensional materials [25]. It

• [27][28][29]. PTCDA molecules were deposited from custom-built Knudsen cells heated to 290–300 °C. Samples were held at room temperature during deposition unless noted otherwise. STM data were acquired at 77 or 5 K using a ScientaOmicron qPlus LT AFM/STM operated by a MATRIX controller and an atom

Oxidation of Au/Ag films by oxygen plasma: phase separation and generation of nanoporosity

• Abdel-Aziz El Mel,
• Said A. Mansour,
• Mujaheed Pasha,
• Atef Zekri,
• Janarthanan Ponraj,
• Akshath Shetty and
• Yousef Haik

Beilstein J. Nanotechnol. 2020, 11, 1608–1614, doi:10.3762/bjnano.11.143

• % of silver and gold, respectively, as determined by EDS. The deposition time was 15 min, the deposition pressure was fixed at 10 mTorr and the distance between the substrate and the targets was ≈10 cm. All deposition processes were carried out on single crystal silicon wafers at a 30 rpm rotation

• speed and no intentional heating was applied to the substrate during the procedure. To ensure a proper adhesion of the Au/Ag alloy films, prior to each deposition a ≈100 nm thick chromium layer was deposited by sputtering of a chromium target (99.99% in purity), under pure argon atmosphere at 10 mT, for

High-responsivity hybrid α-Ag₂S/Si photodetector prepared by pulsed laser ablation in liquid

• Raid A. Ismail,
• Hanan A. Rawdhan and
• Duha S. Ahmed

Beilstein J. Nanotechnol. 2020, 11, 1596–1607, doi:10.3762/bjnano.11.142

• hydrothermal methods, chemical bath deposition, laser ablation in liquid reverse microemulsion, electrospinning, sol–gel, electrochemical method, template method, sonochemical method, and hydrochemical bath deposition [10][11][12][13]. The size of Ag2S NPs depends on the preparation conditions [14]. Ag2S NPs

• , a SiO2 thin film was grown on the silicon substrate before Ag2S deposition through rapid thermal oxidation (RTO) at a temperature of 950 °C for 25 s, and then HF etchant was used to open a Si window on SiO2. The experimental details regarding the RTO process are presented elsewhere [20]. To

• the Ag2S NP surfaces. The reason for the formation of monodisperse Ag2S NPs when CTAB was used as a surfactant can be ascribed to the deposition of CTAB on the Ag2S NP surface, which resulted in a certain repulsive force to other Ag2S NPs. This force may have prevented the agglomeration of the Ag2S

Fabrication of nano/microstructures for SERS substrates using an electrochemical method

• Jingran Zhang,
• Tianqi Jia,
• Xiaoping Li,
• Junjie Yang,
• Zhengkai Li,
• Guangfeng Shi,
• Xinming Zhang and
• Zuobin Wang

Beilstein J. Nanotechnol. 2020, 11, 1568–1576, doi:10.3762/bjnano.11.139

• Pt substrates using a sonoelectrochemical ORC method with different ratios between the time periods of deposition and dissolution. The detection level of R6G molecules was 2 × 10−13 mol·L−1 and the highest enhancement factor achieved was 2.3 × 108. Yang et al. [36] used ORC treatments in KCl solution