Interaction of Te and Se interlayers with Ag or Au nanofilms in sandwich structures

• Arkadiusz Ciesielski,
• Lukasz Skowronski,
• Marek Trzcinski,
• Ewa Górecka,
• Wojciech Pacuski and
• Tomasz Szoplik

Beilstein J. Nanotechnol. 2019, 10, 238–246, doi:10.3762/bjnano.10.22

• the crystallinity, atomic concentration profile and optical parameters of ≈35 nm-thick silver and gold layers deposited on glass substrates with 2 nm-thick tellurium or selenium interlayers. Our study, based on X-ray reflectometry (XRR), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS

• ) and ellipsometric measurements, showed that using either of these interlayers introduces strain in nanocrystals of both plasmonic films. This, in turn, influences the migration of Se and Te into the metal layers. Selenium atoms migrate both in the silver and gold nanolayers, while tellurium atoms

• migrate only in silver. The Te concentration curve clearly suggests that this migration is an effect of the segregation of Te atoms in the silver structure. The differences in crystallinity, as well as the migration process, strongly influence the optical parameters of Ag and Au. In the permittivity of Ag

Mechanism of silica–lysozyme composite formation unravelled by in situ fast SAXS

• Tomasz M. Stawski,
• Daniela B. van den Heuvel,
• Rogier Besselink,
• Dominique J. Tobler and
• Liane G. Benning

Beilstein J. Nanotechnol. 2019, 10, 182–197, doi:10.3762/bjnano.10.17

• -range at small angles was calibrated against silver behenate, and the intensity was calibrated to absolute units against water. For the in situ experiment, first, the starting silica NP solution was continuously circulated between the reactor (where the suspension was stirred at 500 rpm) and the flow

Nanoporous water oxidation electrodes with a low loading of laser-deposited Ru/C exhibit enhanced corrosion stability

• Sandra Haschke,
• Dmitrii Pankin,
• Vladimir Mikhailovskii,
• Maïssa K. S. Barr,
• Adriana Both-Engel,
• Alina Manshina and
• Julien Bachmann

Beilstein J. Nanotechnol. 2019, 10, 157–167, doi:10.3762/bjnano.10.15

• plate connected to a closed-circuit cooler by Haake. The PVC beaker was filled with the electrolyte and closed with a lid equipped with a mechanical stirrer and silver wire mesh as counter-electrode. The whole setup was thermally insulated laterally. Electropolishing of the aluminum plates in a cooled

Wet chemistry route for the decoration of carbon nanotubes with iron oxide nanoparticles for gas sensing

• Hussam M. Elnabawy,
• Juan Casanova-Chafer,
• Badawi Anis,
• Mostafa Fedawy,
• Mattia Scardamaglia,
• Carla Bittencourt,
• Ahmed S. G. Khalil,
• Eduard Llobet and
• Xavier Vilanova

Beilstein J. Nanotechnol. 2019, 10, 105–118, doi:10.3762/bjnano.10.10

• %) Sulfuric acid, J. T. Baker (H2SO4 95–97%) Conductive silver paste, Sigma-Aldrich Methanol, Scharlau (CH3OH 99.9%) Ethanol, Scharlau (C2H5OH 96% extra pure and 99.5% absolute) Acetone, Scharlau (C3H6O 99.5%) Dimethylformamide (DMF), Alfa Aesar (C3H7NO 99.8%) Iron(III) nitrate nonahydrate, Sigma-Aldrich (Fe

• at 1100 °C for 6 hours, were used as substrate. Heaters were attached to the back side of the sensor substrate using silver paste from Sigma-Aldrich. The substrates were heated in the oven at 120 °C for 30 minutes to cure the silver paste. A dispersion in DMF was prepared with a concentration of 0.1

• layer were connected to a printed circuit board (PCB) using platinum wires. Those wires were attached to the heaters and CNT layers using silver paste that was cured in an oven at 120 °C for 30 minutes. To connect the Pt wires to the PCB we used tin wire and a soldering iron. Wire bonded sensors ready

Surface plasmon resonance enhancement of photoluminescence intensity and bioimaging application of gold nanorod@CdSe/ZnS quantum dots

• Siyi Hu,
• Yu Ren,
• Yue Wang,
• Jinhua Li,
• Junle Qu,
• Liwei Liu,
• Hanbin Ma and
• Yuguo Tang

Beilstein J. Nanotechnol. 2019, 10, 22–31, doi:10.3762/bjnano.10.3

• and biophotonics applications. Experimental Materials and instrumentation Hexadecyltrimethylammonium bromide (CTAB, >98.0%), L-ascorbic acid (BioUltra, ≥99.5%), silver nitrate (AgNO3, >99%), gold(III) chloride trihydrate (HAuCl4·3H2O, 99%), 3-mercaptopropionic acid (MPA, ≥99%), N-ethyl-N'-(3

Colloidal chemistry with patchy silica nanoparticles

• Pierre-Etienne Rouet,
• Cyril Chomette,
• Laurent Adumeau,
• Etienne Duguet and
• Serge Ravaine

Beilstein J. Nanotechnol. 2018, 9, 2989–2998, doi:10.3762/bjnano.9.278

• and composition. These new colloidal analogues of molecules could serve as building blocks for the assembly of the next generation (meta-)materials. For example, attaching four different satellites (such as one gold, one silver, one iron oxide and one semiconductor nanoparticle) around a central sp3

Hybrid Au@alendronate nanoparticles as dual chemo-photothermal agent for combined cancer treatment

• Anouchka Plan Sangnier,
• Romain Aufaure,
• Laurence Motte,
• Claire Wilhelm,
• Erwann Guenin and
• Yoann Lalatonne

Beilstein J. Nanotechnol. 2018, 9, 2947–2952, doi:10.3762/bjnano.9.273

• ]. More recently, synthesis of gold and silver NPs have been developed using HMPB molecules [16][17][18]. For gold NPs, HMBPs act as both Au chelating and reducing agent comparable to citrates in the well-known Turkevich–Frens synthesis [19][20]. Besides, gold NPs exhibit a unique surface plasmonic

Controlling surface morphology and sensitivity of granular and porous silver films for surface-enhanced Raman scattering, SERS

• Sherif Okeil and
• Jörg J. Schneider

Beilstein J. Nanotechnol. 2018, 9, 2813–2831, doi:10.3762/bjnano.9.263

• plasmas on the surface morphology of thin silver films. It was found that different surface structures and different degrees of surface roughness could be obtained by a systematic variation of the plasma type and condition as well as plasma power and treatment time. The differently roughened silver

• surfaces act as efficient SERS substrates showing greater enhancement factors compared to as prepared, sputtered, but untreated silver films when using rhodamine B as Raman probe molecule. The obtained roughened silver films were fully characterized by scanning electron microscopy (SEM), atomic force

• conditions. These silver films show a broad range of tunable SERS enhancement factors ranging from 1.93 × 102 to 2.35 × 105 using rhodamine B as probe molecule. The main factors that control the enhancement are the plasma gas used and the plasma conditions, i.e., pressure, power and treatment time

Comparative biological effects of spherical noble metal nanoparticles (Rh, Pd, Ag, Pt, Au) with 4–8 nm diameter

• Alexander Rostek,
• Marina Breisch,
• Kevin Pappert,
• Kateryna Loza,
• Marc Heggen,
• Manfred Köller,
• Christina Sengstock and
• Matthias Epple

Beilstein J. Nanotechnol. 2018, 9, 2763–2774, doi:10.3762/bjnano.9.258

• determine the effect of particle exposure on the viability of human mesenchymal stem cells (hMSCs). Except for silver, no adverse effect of any of the metal nanoparticles was observed for concentrations up to 50 ppm (50 mg L−1) incubated for 24 h, indicating that noble metal nanoparticles (rhodium

• , and nanomedicine [1][2][3]. Noble metal nanoparticles are of particular importance due to their diverse properties such as surface plasmon resonance, chemical inertness, and antibacterial action (silver) [4][5][6][7][8][9]. However, concerns have been raised with respect to their biological effect

• biological effects of rhodium nanoparticles except that these nanoparticles can penetrate into human skin [32]. Silver nanoparticles are applied in various fields including healthcare and biomedicine due to their antimicrobial, antifungal and antiviral effect [33][34][35][36][37]. This is based on the

Low cost tips for tip-enhanced Raman spectroscopy fabricated by two-step electrochemical etching of 125 µm diameter gold wires

• Antonino Foti,
• Francesco Barreca,
• Enza Fazio,
• Cristiano D’Andrea,
• Paolo Matteini,
• Onofrio Maria Maragò and
• Pietro Giuseppe Gucciardi

Beilstein J. Nanotechnol. 2018, 9, 2718–2729, doi:10.3762/bjnano.9.254

• addition, all the above-cited methods require very expensive lab equipment and skilled operators. Electrochemical etching, although suffering from surface roughness issues (mainly for silver), reproducibility issues and lack of tip dimension control, is a technique that is easy to implement, accessible to

Optimization of Mo/Cr bilayer back contacts for thin-film solar cells

• Nima Khoshsirat,
• Fawad Ali,
• Vincent Tiing Tiong,
• Mojtaba Amjadipour,
• Hongxia Wang,
• Mahnaz Shafiei and
• Nunzio Motta

Beilstein J. Nanotechnol. 2018, 9, 2700–2707, doi:10.3762/bjnano.9.252

• silver collection grid was deposited on top using electron-beam evaporation. It is worth mentioning that the fabrication of a cell on a single-layer Mo-coated glass also has been tried. However, the Mo films were peeled-off from the substrate during CdS CBD. Thus, herein only the performance of a cell

Silicene, germanene and other group IV 2D materials

• Patrick Vogt

Beilstein J. Nanotechnol. 2018, 9, 2665–2667, doi:10.3762/bjnano.9.248

• concepts exploiting their topological properties. In recent years this search has lead to the discovery of other members of this family of 2D materials based on other group IV elements. In 2012 silicene was first synthesized under ultrahigh vacuum conditions on a silver(111) single crystal by Si molecular

Polarization-dependent strong coupling between silver nanorods and photochromic molecules

• Gwénaëlle Lamri,
• Alessandro Veltri,
• Jean Aubard,
• Pierre-Michel Adam,
• Nordin Felidj and
• Anne-Laure Baudrion

Beilstein J. Nanotechnol. 2018, 9, 2657–2664, doi:10.3762/bjnano.9.247

• Abstract Active plasmonics is a key focus for the development of advanced plasmonic applications. By selectively exciting the localized surface plasmon resonance sustained by the short or the long axis of silver nanorods, we demonstrate a polarization-dependent strong coupling between the plasmonic

• latter is always observed when the plasmon or the molecular exciton presents a large oscillator strength and leads to the splitting of the main resonance. We previously demonstrated a reversible, strong coupling between silver cylindrical nanoparticles and photochromic molecules, both considered as

• lithography to fabricate large arrays of silver nanorods on a glass substrate. The pitch of the arrays has been varied to keep the filling factor approximately equal to 10% and to avoid any lattice mode contribution in the optical spectra. For three different nanorod widths (70, 90 and 110 nm), the nanorod

Characterization of the microscopic tribological properties of sandfish (Scincus scincus) scales by atomic force microscopy

• Weibin Wu,
• Christian Lutz,
• Simon Mersch,
• Richard Thelen,
• Christian Greiner,
• Guillaume Gomard and
• Hendrik Hölscher

Beilstein J. Nanotechnol. 2018, 9, 2618–2627, doi:10.3762/bjnano.9.243

• ). Sandfish scales were sputtered with 20 nm of silver before imaging while the probes were not sputtered in order to prevent unwanted changes of the surface properties for the adhesion measurements. Therefore, a low working distance between probes and SEM detector and a low acceleration voltage between 1 and

Enhancement of X-ray emission from nanocolloidal gold suspensions under double-pulse excitation

• Wei-Hung Hsu,
• Frances Camille P. Masim,
• Armandas Balčytis,
• Hsin-Hui Huang,
• Tetsu Yonezawa,
• Aleksandr A. Kuchmizhak,
• Saulius Juodkazis and
• Koji Hatanaka

Beilstein J. Nanotechnol. 2018, 9, 2609–2617, doi:10.3762/bjnano.9.242

• with different sizes was applied for the efficient X-ray generation in an aqueous phase [17][18], and plasmonic silver nanoparticles were excited to accelerate electrons in vaccum [19]. In addition, there is another new theoretical approach on X-ray sources using plasmonic graphene [20]. Nanoparticles

• of silver [21] or aluminum [22] could be also considered. However, experimental approaches have been limited to flat samples [23] so far. Gold, with the higher atomic number and a high stability even in aqueous environments, should be considered a main target for fs-laser-induced X-ray experiments

Enhanced antineoplastic/therapeutic efficacy using 5-fluorouracil-loaded calcium phosphate nanoparticles

• Shanid Mohiyuddin,
• Saba Naqvi and
• Gopinath Packirisamy

Beilstein J. Nanotechnol. 2018, 9, 2499–2515, doi:10.3762/bjnano.9.233

• nanomaterial was found to be toxic in some metal-based NPs (e.g., gold, silver, iron, and copper), while the bulk counterparts showed less toxicity [9]. The metal ions present at the surface of the particles were found to interact with biomolecules at a comparatively higher rate in nanoformulations compared to

• inhibit the cancer cells of an oral squamous cell carcinoma (OSCC) mouse xenograft model with increased blood retention time [20]. Furthermore, a poly(amidoamine) (PAMAM) dendrimer stabilized with a silver nanoparticle surface for the encapsulation of 5-FU showed synergistic growth inhibition in A549 and

Nanocellulose: Recent advances and its prospects in environmental remediation

• Katrina Pui Yee Shak,
• Yean Ling Pang and
• Shee Keat Mah

Beilstein J. Nanotechnol. 2018, 9, 2479–2498, doi:10.3762/bjnano.9.232

SERS active Ag–SiO₂ nanoparticles obtained by laser ablation of silver in colloidal silica

• Cristina Gellini,
• Francesco Muniz-Miranda,
• Alfonso Pedone and
• Maurizio Muniz-Miranda

Beilstein J. Nanotechnol. 2018, 9, 2396–2404, doi:10.3762/bjnano.9.224

• , 41125 Modena, Italy Center for Molecular Modeling, Ghent University, Technologiepark 903, 9052 Zwijnaarde, Belgium 10.3762/bjnano.9.224 Abstract Highly stable Ag–SiO2 nanoparticle composites were first obtained by laser ablation of a silver target in an aqueous colloidal dispersion of silica and

• computational DFT approach provided evidence of ligand adsorption on positively charged adatoms of the silver nanostructured surface, in a very similar way to the metal/molecule interaction occurring in the corresponding Ag(I) coordination compound. Keywords: 2,2’-bipyridine; DFT; laser ablation; silica

• ; silver; Introduction Silica nanoparticles in an aqueous suspension are known to be inert and dispersible – properties which can be quite useful in the preparation of colloidal nanocomposites with silver. For this reason, there are a significant number of studies in the literature on colloidal substrates

Hierarchical heterostructures of Bi₂MoO₆ microflowers decorated with Ag₂CO₃ nanoparticles for efficient visible-light-driven photocatalytic removal of toxic pollutants

• Shijie Li,
• Wei Jiang,
• Shiwei Hu,
• Yu Liu,
• Yanping Liu,
• Kaibing Xu and
• Jianshe Liu

Beilstein J. Nanotechnol. 2018, 9, 2297–2305, doi:10.3762/bjnano.9.214

• candidate for wastewater treatment. Keywords: antibiotic removal; Bi2MoO6; heterojunction; silver carbonate (Ag2CO3); Introduction Industrial pollutants, such as industrial dyes and antibiotics, in wastewaters pose a huge threat to the environment [1][2]. Thus, many methods for pollutant removal have been

Surface energy of nanoparticles – influence of particle size and structure

• Dieter Vollath,
• Franz Dieter Fischer and
• David Holec

Beilstein J. Nanotechnol. 2018, 9, 2265–2276, doi:10.3762/bjnano.9.211

• expectation of a reduced surface energy. Results for silver nanoparticles, shown by Alarifi et al. [46], demonstrate the existence of both an outer liquid layer and subsequent a quasi-liquid transition layer at the surface of nanoparticles. Even when both the quasi-liquid and the liquid layer are not

• crystallized, they can be distinguished by their energy. Figure 9 displays the thickness of these two kinds of surface layers for 18 nm gold particles as function of the temperature. These layers, with reduced order, are observed (at least for silver particles) at temperatures not too much below the melting

• application of this computational strategy can be found in papers from Medasani et al. [49][58][59]. Figure 16 displays the results for calculations of the surface energy of silver particles [49][58]. (The abbreviation DFT-GGA stands for density functional theory using a generalized gradient approximation

The role of adatoms in chloride-activated colloidal silver nanoparticles for surface-enhanced Raman scattering enhancement

• Nicolae Leopold,
• Andrei Stefancu,
• Krisztian Herman,
• István Sz. Tódor,
• Stefania D. Iancu,
• Vlad Moisoiu and
• Loredana F. Leopold

Beilstein J. Nanotechnol. 2018, 9, 2236–2247, doi:10.3762/bjnano.9.208

• Medicine, Manastur 3-5, 400372 Cluj-Napoca, Romania 10.3762/bjnano.9.208 Abstract Chloride-capped silver nanoparticles (Cl-AgNPs) allow for high-intensity surface-enhanced Raman scattering (SERS) spectra of cationic molecules to be obtained (even at nanomolar concentration) and may also play a key role in

• understanding some fundamental principles behind SERS. In this study, we describe a fast (<10 min) and simple protocol for obtaining highly SERS-active colloidal silver nanoparticles (AgNPs) with a mean diameter of 36 nm by photoconversion from AgCl precursor microparticles in the absence of any organic

• silver metal surface. Moreover, the SERS effect is switched on only after the electronic coupling of the adsorbate to the silver surface at SERS-active sites. The experiments presented in this study highlight the SERS-activating role played by ions such as Cl−, Ag+, Mg2+ or Ca2+, which is a process that

Lead-free hybrid perovskites for photovoltaics

• Oleksandr Stroyuk

Beilstein J. Nanotechnol. 2018, 9, 2209–2235, doi:10.3762/bjnano.9.207

Fabrication of photothermally active poly(vinyl alcohol) films with gold nanostars for antibacterial applications

• Mykola Borzenkov,
• Maria Moros,
• Claudia Tortiglione,
• Serena Bertoldi,
• Nicola Contessi,
• Silvia Faré,
• Angelo Taglietti,
• Agnese D’Agostino,
• Piersandro Pallavicini,
• Maddalena Collini and
• Giuseppe Chirico

Beilstein J. Nanotechnol. 2018, 9, 2040–2048, doi:10.3762/bjnano.9.193

• studies have reported the preparation and the antibacterial efficacy of PVA films containing plant extracts, silver nanoparticles or zinc oxide nanoparticles [17][18][19][20][21][22]. However, when bacteria start to form biofilms they become resistant and conventional antibiotics do not eradicate biofilms

• from the surfaces where they formed [8]. Silver nanoparticles prevent biofilm formation but with a controversial results – Ag nanoparticles are effective towards Gram-negative bacterial strains but much less so towards Gram-positive [8][23]. There is a strong need for novel lightweight antibacterial

• ) were commercially available from Fluka. Poly(ethylene glycol) thiols ( = 5000 g/mol; SH-PEG5000–OCH3 and SH-PEG5000–COOH), polyethylene glycol tert-octylphenyl ether (Triton X-100), chloroauric acid, ascorbic acid, silver nitrate, and sodium borohydride were purchased from Sigma-Aldrich and used as

Synthesis of rare-earth metal and rare-earth metal-fluoride nanoparticles in ionic liquids and propylene carbonate

• Marvin Siebels,
• Lukas Mai,
• Laura Schmolke,
• Kai Schütte,
• Juri Barthel,
• Junpei Yue,
• Jörg Thomas,
• Bernd M. Smarsly,
• Anjana Devi,
• Roland A. Fischer and
• Christoph Janiak

Beilstein J. Nanotechnol. 2018, 9, 1881–1894, doi:10.3762/bjnano.9.180

• and a sample angle of 33°. Spectra were recorded using polychromatic Al Kα excitation (11 kV, 20 mA) and an emission angle of 0°. Calibration of the XPS was carried out by recording spectra with Al Kα X-rays from clean samples of copper, silver and gold at 50 eV and 10 eV pass energy and comparison

Synthesis of hafnium nanoparticles and hafnium nanoparticle films by gas condensation and energetic deposition

• Irini Michelakaki,
• Nikos Boukos,
• Dimitrios A. Dragatogiannis,
• Spyros Stathopoulos,
• Costas A. Charitidis and
• Dimitris Tsoukalas

Beilstein J. Nanotechnol. 2018, 9, 1868–1880, doi:10.3762/bjnano.9.179

• the sensitivity of gas sensors [12], twinned silver NPs show important different chemical activity compared to their single crystalline counterparts [13]. These and many other examples illustrate that investigating the morphology and structure of metal NPs is essential for their efficient utilization